M.J. Arcos-Martínez

CYP450 2B4 covalently attached to carbon and gold screen printed electrodes by diazonium salt and thiols monolayers.

An easy covalent immobilization method used to develop enzyme biosensors based on carbon and gold screen printed electrodes (SPCEs and gold SPEs) is described. The linkage of biomolecules through 4-nitrobenzenediazonium tetrafluoroborate, mercaptopropionic acid and thioctic acid monolayers has been attempted using bare SPCEs and gold SPEs, as well as gold nanoparticles (AuNPs) modified SPCEs and gold SPEs. Direct covalent attachment of Cytochrome P450 2B4 (CYP450 2B4) to the transducer has been carried out by carbodiimide and hydroxysuccinimide. Experimental variables in the immobilization process and in the chronoamperometric determination of Phenobarbital (PB) have been optimized by the experimental design methodology. Reproducibility of the different biosensors has been checked under the optimum conditions, yielding values lower than 6%. Their performances have been shown by the determination of PB in pharmaceutical drugs.

Immobilization of Acetylcholinesterase on Screen-Printed Electrodes. Application to the Determination of Arsenic(III)

Enzymatic amperometric procedures for measuring arsenic, based on the inhibitive action of this metal on acetylcholinesterase enzyme activity, have been developed. Screen-printed carbon electrodes (SPCEs) were used with acetylcholinesterase covalently bonded directly to its surface. The amperometric response of acetylcholinesterase was affected by the presence of arsenic ions, which caused a decrease in the current intensity. The experimental optimum working conditions of pH, substrate concentration and potential applied, were established. Under these conditions, repeatability and reproducibility of biosensors were determined, reaching values below 4% in terms of relative standard deviation. The detection limit obtained for arsenic was 1.1 × 10−8 M for Ach/SPCE biosensor. Analysis of the possible effect of the presence of foreign ions in the solution was performed. The method was applied to determine levels of arsenic in spiked tap water samples.

Development of urease based amperometric biosensors for the inhibitive determination of Hg (II).

Enzymatic amperometric procedures for measurement of Hg (II), based on the inhibitive action of this metal on urease enzyme activity, were developed. Screen-printed carbon electrodes (SPCEs) and gold nanoparticles modified screen-printed carbon electrodes (AuNPs/SPCEs) were used as supports for the cross-linking inmobilization of the enzyme urease. The amperometric response of urea was affected by the presence of Hg (II) ions which caused a decreasing in the current intensity. The optimum working conditions were found using experimental design methodology. Under these conditions, repeatability and reproducibility for both types of biosensors were determined, reaching values below 6% in terms of residual standard deviation. The detection limit obtained for Hg (II) was 4.2x10(-6)M for urease/SPCE biosensor and 5.6x10(-8)M for urease/AuNPs/SPCE biosensor. Analysis of the possible effect of the presence of foreign ions in the solution was performed. The method was applied to determine levels of Hg (II) in spiked human plasma samples.

CYP450 biosensors based on gold chips for antiepileptic drugs determination

Three-electrode configuration chips containing a Pt, Au and a screen-printed Ag/AgCl as counter, working and reference electrode, respectively, have been developed. Selective determination of Phenobarbital (PB) has been carried out by Cytochrome P450 2B4 (CYP450) immobilization into a polypyrrole matrix onto the gold working electrode. Chronoamperometric experiments show a PB diffusion coefficient of 2.42x10(-6)cm(2)s(-1), a reproducibility and repeatability in terms of residual standard deviation (RSD) of 13% and 5.51%, respectively, and a limit of detection (LOD) of 0.289 micromol dm(-3) (alpha=beta=0.05) for the developed CYP450-biosensor chip. Its performance has been showed by the determination of PB in pharmaceutical drugs. HPLC has been used as reference technique.

Development of acid phosphatase based amperometric biosensors for the inhibitive determination of As(V)

An enzymatic amperometric procedure for the direct measurement of As(V) in the presence of As(III) was developed. The method is based on the inhibitive action of this species on acid phosphatase enzyme (AcP) activity. Screen-printed carbon electrodes (SPCEs) were used as support for the cross-linking immobilization of the enzyme AcP. 2-Phospho-l-ascorbic acid was used as a novel substrate, in arsenic determination, which amperometric response decreased by the presence of As(V) ions. The optimum working conditions were found using experimental design methodology. Under these conditions, repeatability and reproducibility of the constructed biosensors were determined, reaching values below 8% in terms of residual standard deviation. The capability of detection obtained for As(V) was 0.11 μM for AcP/SPCE biosensors. Analysis of the possible effect of the presence of foreign ions in the solution was performed. The method was successfully applied to the determination of the As(V) content in a ground water sample.

Resolution of quaternary mixtures of cadaverine, histamine, putrescine and tyramine by the square wave voltammetry and partial least squares method.

This work presents the simultaneous determination of cadaverine, histamine, putrescine and tyramine by square wave voltammetry using a boron-doped diamond electrode. A multivariate calibration method based on partial least square regressions has allowed the resolution of the very high overlapped voltammetric signals obtained for the analyzed biogenic amines. Prediction errors lower than 9% have been obtained when concentration of quaternary mixtures were calculated. The developed procedure has been applied in the analysis of ham samples, which results are in good agreement with those obtained using the standard HPLC method.

Thick-film voltammetric pH-sensors with internal indicator and reference species.

The following paper describes the development of a screen-printed voltammetric pH-sensor based on graphite electrodes incorporating both internal indicator (i.e., phenanthraquinone) and reference species (i.e., dimethylferrocene). The key advantages of this type of system stem from its simplicity, low cost and ease of fabrication. More importantly, as opposed to conventional voltammetric systems where the height of the voltammetric peaks is taken into account to quantify the amount of a species of interest, here, the difference between the peak potential of the indicator species and the peak potential of the reference species is used. Thus, this measurement principle makes the electrochemical system presented here less dependent on the potential of the reference electrode (RE), as is often the case in other electrochemical systems. The developed system displays very promising performances, with a reproducible Super Nernstian response to pH changes and a lifetime of at least nine days.

Disposable immunosensor for human cytomegalovirus glycoprotein B detection

Combining the advantages of the biosensor field with the problem of detecting Human Cytomegalovirus (HCMV) in human samples, an inexpensive, simple and disposable electrochemical immunosensor for glycoprotein B detection in urine is proposed. Glycoprotein B has been chosen once is the dominant antigen of HCMV. The approach is based on a sandwich-type immunoassay, with the HCMV glycoprotein B sandwiched between the Anti-HCMV antibody adsorbed onto the working electrode, and the Anti-HCMV labeled with gold nanoparticles. Glycoprotein B detection was carried out through electrochemical stripping analysis of silver nanoparticles quantitatively deposited on the immunosensor through catalysis by the nanogold labels. The influence of different steps in the immunosensor construction, namely the silver deposition time, silver enhancer concentration, antibody concentration, BSA concentration and glycoprotein B incubation time, were examined and optimized. The method showed a linear dependence between glycoprotein B concentration and the corresponding anodic stripping peak current, resulting in detection limits of 3.3±1.7ng/mL for samples prepared in buffer and 3.2±0.2ng/mL for urine samples, suggesting that the biological matrix does not interfere with the immunosensor detection capability. Given its mode of preparation, by physical adsorption of the capture antibody in the working electrode, the immunosensor also exhibited an acceptable reproducibility, with a residual standard deviation of 13.5% for samples prepared in buffer and 11.2% for urine samples, thereby presenting a promising development potential for clinical applications.

Determination of halides using Ag nanoparticles-modified disposable electrodes. A first approach to a wearable sensor for quantification of chloride ions

This work reports a simple voltammetric method for the determination of chloride, bromide, and iodide ions using screen-printed carbon electrodes modified with silver nanoparticles electrochemically deposited on the working electrode surface. UV/Vis absorption spectroelectrochemistry was used to study the electrodeposition of silver nanoparticles on the working carbon electrode on PET or Gore-Tex® supports, and their subsequent oxidation in the presence of halide ions. The main figures of merit of the developed sensors, such as reproducibility and detection limit, have been calculated. Reproducibility values of 2.22%, 2.83% and 3.23% were obtained for chloride, bromide and iodide determinations, respectively. Additionally, the lowest detected amount of chloride, bromide and iodide ions were 3.0·10-6 M, 5.0·10-6 M and 5.0·10-6 M, respectively. Taking into account the relevance of the determination of chloride ion concentration in sweat, the voltammetric method for the determination of halides has been successfully transferred to a Gore-Tex® support to build a first approach to a wearable sensor that facilitates the quantification of this ion in sweat samples. The Gore-Tex® sensor provides a good reproducibility (RSD = 1.61%).

Effect of Nanoparticles on Modified Screen Printed Inhibition Superoxide Dismutase Electrodes for Aluminum

A novel amperometric biosensor for the determination of Al(III) based on the inhibition of the enzyme superoxide dismutase has been developed. The oxidation signal of epinephrine substrate was affected by the presence of Al(III) ions leading to a decrease in its amperometric current. The immobilization of the enzyme was performed with glutaraldehyde on screen-printed carbon electrodes modifiedwith tetrathiofulvalene (TTF) and different types ofnanoparticles. Nanoparticles of gold, platinum, rhodium and palladium were deposited on screen printed carbon electrodes by means of two electrochemical procedures. Nanoparticles were characterized trough scanning electronic microscopy, X-rays fluorescence, and atomic force microscopy. Palladium nanoparticles showed lower atomic force microscopy parameters and higher slope of aluminum calibration curves and were selected to perform sensor validation. The developed biosensor has a detection limit of 2.0 ± 0.2 μM for Al(III), with a reproducibility of 7.9% (n = 5). Recovery of standard reference material spiked to buffer solution was 103.8% with a relative standard deviation of 4.8% (n = 5). Recovery of tap water spiked with the standard reference material was 100.5 with a relative standard deviation of 3.4% (n = 3). The study of interfering ions has also been carried out.