M. Jesionek

Sonochemical growth of antimony sulfoiodide in multiwalled carbon nanotube.

This paper presents for the first time the nanocrystalline, semiconducting ferroelectrics antimony sulfoiodide (SbSI) grown in multiwalled carbon nanotubes (CNTs). It was prepared sonochemically using elemental Sb, S and I in the presence of methanol under ultrasonic irradiation (35kHz, 2.6W/cm(2)) at 323K for 3h. The CNTs filled with SbSI were characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, and optical diffuse reflection spectroscopy. These investigations exhibit that the SbSI filling the CNTs is single crystalline in nature and in the form of nanowires. It has indirect forbidden energy band gap E(gIf)=1.871(1)eV.

Sonochemical preparation of SbSeI gel

A novel sonochemical method for direct preparation of nanocrystalline antimony selenoiodide (SbSeI) has been established. The SbSeI gel was synthesized using elemental Sb, Se, and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2W/cm(2)) at 50 degrees C for 2h. The product was characterized by using techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and optical diffuse reflection spectroscopy (DRS). The SEM and HRTEM investigations exhibit that the as-prepared samples are made up of large quantity nanowires with lateral dimensions of about 20-50 nm and lengths reaching up to several micrometers and single crystalline in nature.

Influence of the solvent on ultrasonically produced SbSI nanowires

The influence of the substitution of methanol in place of ethanol during the ultrasonic production of antimony sulfoiodide (SbSI) nanowires is presented. The new technology is faster and more efficient at temperatures greater than 314 K. The products were characterized by using techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDXA), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), optical diffuse reflection spectroscopy (DRS) and IR spectroscopy. The coexistence of Pna2(1) (ferroelectric) and Pnam (paraelectric) phases at 298 K was observed in the SbSI nanowires produced in methanol. The methanol decomposes during the sonication or due to the adsorption process on SbSI nanowires.

Sonochemical growth of nanomaterials in carbon nanotube

HighlightsParameters of sonochemical encapsulation of SbSI and SbSeI in CNTs.SbSI@CNTs and SbSeI@CNTs bonded ultrasonically with microelectrodes.200% increase of conductance due to ultrasonic bonding of filled CNTs to Au.SbSI@CNTs and SbSeI@CNTs gas sensors do not require heating system for recovery.SbSI@CNTs structures applied to detect carbon dioxide. ABSTRACT Recent achievements in investigations of carbon nanotubes (CNTs) filled with ternary chalcohalides (antimony sulfoiodide (SbSI) and antimony selenoiodide (SbSeI)) are presented. Parameters of sonochemical encapsulation of nanocrystalline semiconducting ferroelectric SbSI‐type materials in CNTs are reported. This low temperature technology is convenient, fast, efficient and environmentally friendly route for producing novel type of hybrid materials useful for nanodevices. Structure as well as optical and electrical properties of SbSI@CNTs and SbSeI@CNTs are described. Advantages of ultrasonic joining of such filled CNTs with metal microelectrodes are emphasized. The possible applications of these nanomaterials as gas sensors are shown.

Addition of a small amount of multiwalled carbon nanotubes and flaked graphene to epoxy resin

The paper presents an attempt to evaluate the technically important properties of epoxy resin modified alternatively with multi-walled carbon nanotubes and flaked graphene. It is a presentation of experimental results supported by extensive referring to the professional literature. The nano-components were added in the amount which was economically justified and provides hope for a significant improvement of some of the properties of pure resin. Flowability, glass wettability, curing process and gelation time and curing shrinkage of the resin were evaluated. After the resin was cured, inner and outer hardness, thermal conductivity, flexural strength and impact resistance were measured. Glass fibre-reinforced laminates were also prepared with use of the nano-modified resin. The mechanical properties, interlaminar shear strength and flexural strength of the laminates, were evaluated for them. The obtained results showed either no effect or only technically slight effect of the nano-modification on the evaluated properties. Noticeable improvement in interlaminar shear strength and impact resistance for laminates containing resin filled with graphene can predestine this kind of modification as a method of increasing the delamination resistance of laminates.

Using of sonochemically prepared components for vapor phase growing of SbI3·3S8

The using of sonochemically prepared components for growth of SbI(3).3S(8) single crystals from the vapor phase is presented for the first time. The good optical quality of the obtained crystals is important because this material is valuable for optoelectronics due to its non-linear optical properties. The products were characterized by using techniques such as X-ray crystallography, powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, optical diffuse reflection spectroscopy and optical transmittance spectroscopy. The direct and indirect forbidden energy gaps of SbI(3).3S(8) illuminated with plane polarized light with electric field parallel and perpendicular to the c-axis of the crystal have been determined. The second harmonic generation of light in the grown crystals was observed.

Structure of Antimony Sulfoiodide Ultrasonically Prepared in Carbon Nanotubes

This paper presents a brand new hybrid material on the nanometric scale: the antimony sulfoiodide (SbSI) within carbon nanotubes (CNTs). It was prepared in CNTs ultrasonically by using elemental antimony (Sb), sulfur (S) and iodide (I) in the presence of methanol under ultrasonic irradiation (34 kHz, 2.6 W/cm2). The sonochemical process was leaded for 3 hours at 323 K. The antimony sulfoiodide (SbSI) consisted in multiwalled carbon nanotubes (CNTs) were characterized high-resolution transmission electron microscopy (HRTEM). These investigations exhibit that the SbSI filling the CNTs has single-crystal structure in nature and in the form of multiwalled carbon nanotubes. The SbSI grown in CNTs are very promising materials for further investigations as well as for some industrial and medical applications.

Contactless photomagnetoelectric investigations of 2D semiconductors

Background: Applications of two-dimensional (2D) materials in electronic devices require the development of appropriate measuring methods for determining their typical semiconductor parameters, i.e., mobility and carrier lifetime. Among these methods, contactless techniques and mobility extraction methods based on field-effect measurements are of great importance. Results: Here we show a contactless method for determining these parameters in 2D semiconductors that is based on the photomagnetoelectric (PME) effect (also known as the photoelectromagnetic effect). We present calculated dependences of the PME magnetic moment, evoked in 2D Corbino configuration, on the magnetic field as well as on the intensity and spatial distribution of illumination. The theoretical predictions agree with the results of the contactless investigations performed on non-suspended single-layer graphene. We use the contactless PME method for determining the dependence of carrier mobility on the concentration of electrons and holes induced by a back-gate voltage. Conclusion: The presented contactless PME method, used in Corbino geometry, is complementary to the mobility extraction methods based on field-effect measurements. It can be used for determining the mobility and diffusion length of carriers in different 2D materials.