Malte C. Kaluza

The generation of amplified spontaneous emission in high‐power CPA laser systems

Abstract An analytical model is presented describing the temporal intensity contrast determined by amplified spontaneous emission in high‐intensity laser systems which are based on the principle of chirped pulse amplification. The model describes both the generation and the amplification of the amplified spontaneous emission for each type of laser amplifier. This model is applied to different solid state laser materials which can support the amplification of pulse durations ≤350 fs . The results are compared to intensity and fluence thresholds, e.g. determined by damage thresholds of a certain target material to be used in high‐intensity applications. This allows determining if additional means for contrast improvement, e.g. plasma mirrors, are required for a certain type of laser system and application. Using this model, the requirements for an optimized high‐contrast front‐end design are derived regarding the necessary contrast improvement and the amplified “clean” output energy for a desired focussed peak intensity. Finally, the model is compared to measurements at three different high‐intensity laser systems based on Ti:Sapphire and Yb:glass. These measurements show an excellent agreement with the model.

High contrast, 86 fs, 35 mJ pulses from a diode-pumped, Yb:glass, double-chirped-pulse amplification laser system.

We demonstrate the generation of 86 fs, 35 mJ, high-contrast laser pulses at 1030 nm with a repetition rate of 1 Hz from a diode-pumped double chirped-pulse amplification setup. The pulses exhibit a spectral bandwidth exceeding 27 nm full width at half-maximum. This could be achieved by using a laser architecture comprising two stages of chirped pulse amplification with a cross-polarized wave generation filter in between, by applying spectral shaping and by increasing the spectral hard-clip of the second stretcher. These are, to the best of our knowledge, the shortest pulses at the mJ level with ultra-high contrast generated with a diode-pumped front end at 1030 nm.

Optimizing laser-driven proton acceleration from overdense targets.

We demonstrate how to tune the main ion acceleration mechanism in laser-plasma interactions to collisionless shock acceleration, thus achieving control over the final ion beam properties (e. g. maximum energy, divergence, number of accelerated ions). We investigate this technique with three-dimensional particle-in-cell simulations and illustrate a possible experimental realisation. The setup consists of an isolated solid density target, which is preheated by a first laser pulse to initiate target expansion, and a second one to trigger acceleration. The timing between the two laser pulses allows to access all ion acceleration regimes, ranging from target normal sheath acceleration, to hole boring and collisionless shock acceleration. We further demonstrate that the most energetic ions are produced by collisionless shock acceleration, if the target density is near-critical, ne ≈ 0.5 ncr. A scaling of the laser power shows that 100 MeV protons may be achieved in the PW range.

Tunable filters for precise spectral gain control in ultra-short-pulse laser systems

We present tunable spectral filters (TSFs) as a variable and precisely adjustable method to control the spectral gain of short-pulse laser systems. The TSFs provide a small residual spectral phase and a high damage threshold, and generate no pre- or post-pulses. The method is demonstrated for two different laser materials and can be applied as an intracavity compensation in regenerative amplifiers as well as a method for pre-compensation in high-energy multipass amplifiers. With this method, a full width at half-maximum bandwidth of 23.9 nm could be demonstrated in a diode-pumped, 50 J Yb:CaF2 amplifier.

Modeling ultrafast shadowgraphy in laser-plasma interaction experiments

Ultrafast shadowgraphy is a new experimental technique that uses few-cycle laser pulses to image density gradients in a rapidly evolving plasma. It enables structures that move at speeds close to the speed of light, such as laser driven wakes, to be visualized. Here we study the process of shadowgraphic image formation during the propagation of a few cycle probe pulse transversely through a laser-driven wake using three-dimensional particle-in-cell simulations. In order to construct synthetic shadowgrams a near-field snapshot of the ultrashort probe pulse is analyzed by means of Fourier optics, taking into account the effect of a typical imaging setup. By comparing synthetic and experimental shadowgrams we show that the generation of synthetic data is crucial for the correct interpretation of experiments. Moreover, we study the dependence of synthetic shadowgrams on various parameters such as the imaging system aperture, the position of the object plane and the probe pulse delay, duration and wavelength. Finally, we show that time-dependent information from the interaction can be recovered from a single shot by using a broadband, chirped probe pulse and subsequent spectral filtering.

Spatially and temporally resolved temperature measurement in laser media

A technique to measure the spatially resolved temperature distribution in a laser medium is presented. It is based on the temperature dependence of the absorption cross section close to the zero-phonon line of the active medium. Since other materials in the beam path exhibit a high (and constant) transmission at this wavelength, the method can easily be applied in realistic amplifier setups. The method was successfully tested on three different samples, which were pumped by a pulsed laser diode with up to 150 W average power: side-cooled Yb:YAG and Yb:fluoride-phosphate glass at room temperature and face-cooled Yb:CaF2 at 120 K.