Marios Neophytou

Reducing the efficiency-stability-cost gap of organic photovoltaics with highly efficient and stable small molecule acceptor ternary solar cells

Technological deployment of organic photovoltaic modules requires improvements in device light-conversion efficiency and stability while keeping material costs low. Here we demonstrate highly efficient and stable solar cells using a ternary approach, wherein two non-fullerene acceptors are combined with both a scalable and affordable donor polymer, poly(3-hexylthiophene) (P3HT), and a high-efficiency, low-bandgap polymer in a single-layer bulk-heterojunction device. The addition of a strongly absorbing small molecule acceptor into a P3HT-based non-fullerene blend increases the device efficiency up to 7.7 ± 0.1% without any solvent additives. The improvement is assigned to changes in microstructure that reduce charge recombination and increase the photovoltage, and to improved light harvesting across the visible region. The stability of P3HT-based devices in ambient conditions is also significantly improved relative to polymer:fullerene devices. Combined with a low-bandgap donor polymer (PBDTTT-EFT, also known as PCE10), the two mixed acceptors also lead to solar cells with 11.0 ± 0.4% efficiency and a high open-circuit voltage of 1.03 ± 0.01u2009V.

Determination of gap defect states in organic bulk heterojunction solar cells from capacitance measurements

Energy distributions density-of-states DOS of defects in the effective band gap of organic bulk heterojunctions are determined by means of capacitance methods. The technique consists of calculating the junction capacitance derivative with respect to the angular frequency of the small voltage perturbation applied to thin film poly3-hexylthiopheneP3HT6,6-phenyl C61-butyric acid methyl ester PCBM solar cells. The analysis, which was performed on blends of different composition, reveals the presence of defect bands exhibiting Gaussian shape located at E 0.38 eV above the highest occupied molecular orbital level of the P3HT. The disorder parameter , which accounts for the broadening of the Gaussian DOS, lies within the range of 49‐66 meV. The total density of defects results of order 10 16 cm x7f3 .© 2009 American Institute of Physics.

Amorphous Tin Oxide as a Low-Temperature-Processed Electron-Transport Layer for Organic and Hybrid Perovskite Solar Cells

Chemical bath deposition (CBD) of tin oxide (SnO2) thin films as an electron-transport layer (ETL) in a planar-heterojunction n-i-p organohalide lead perovskite and organic bulk-heterojunction (BHJ) solar cells is reported. The amorphous SnO2 (a-SnO2) films are grown from a nontoxic aqueous bath of tin chloride at a very low temperature (55 °C) and do not require postannealing treatment to work very effectively as an ETL in a planar-heterojunction n-i-p organohalide lead perovskite or organic BHJ solar cells, in lieu of the commonly used ETL materials titanium oxide (TiO2) and zinc oxide (ZnO), respectively. Ultraviolet photoelectron spectroscopy measurements on the glass/indium-tin oxide (ITO)/SnO2/methylammonium lead iodide (MAPbI3)/2,2,7,7-tetrakis(N,N-di-p-methoxyphenylamine)-9,9-spirobifluorene device stack indicate that extraction of photogenerated electrons is facilitated by a perfect alignment of the conduction bands at the SnO2/MAPbI3 interface, while the deep valence band of SnO2 ensures strong hole-blocking properties. Despite exhibiting very low electron mobility, the excellent interfacial energetics combined with high transparency (Egap,optical > 4 eV) and uniform substrate coverage make the a-SnO2 ETL prepared by CBD an excellent candidate for the potentially low-cost and large-scale fabrication of organohalide lead perovskite and organic photovoltaics.

Highly efficient indium tin oxide-free organic photovoltaics using inkjet-printed silver nanoparticle current collecting grids

We report an in-depth investigation of an inkjet-printed silver (Ag) nanoparticle grid combined with poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) of different conductivities as an alternative to an indium tin oxide (ITO)-based transparent anode for organic solar cell applications. The reported measurements revealed higher transparency of the inkjet-printed Ag nanoparticle-based grid when compared to different thicknesses of ITO on glass substrates. Based on the proposed current collecting grid, a record power conversion efficiency of 2% is achieved for ITO-free organic solar cells.

Homo-Tandem Polymer Solar Cells with VOC >1.8 V for Efficient PV-Driven Water Splitting.

Efficient homo-tandem and triple-junction polymer solar cells are constructed by stacking identical subcells composed of the wide-bandgap polymer PBDTTPD, achieving power conversion efficiencies >8% paralleled by open-circuit voltages >1.8 V. The high-voltage homo-tandem is used to demonstrate PV-driven electrochemical water splitting with an estimated solar-to-hydrogen conversion efficiency of ≈6%.

Novel BODIPY-based conjugated polymers donors for organic photovoltaic applications

Five new polymers based on the 4,4′-difluoro-4-bora-3a,4a-diaza-s-indacene core (BODIPY) chromophore moiety have been synthesized as low bandgap polymers for optoelectronic applications. The polymers exhibited high solubility in common organic solvents and optical bandgaps ranging from 1.7–2 eV. The materials were characterized using NMR, UV-Vis, steady state and time-resolved photoluminescence and the energy levels were examined using electrochemistry and validated using quantum chemical calculations. Finally, a representative BODIPY derivativeu2006:u2006PCBM blend was examined in terms of photovoltaic properties. Preliminary device performance parameters as a function of photo-active layer thickness and composition are reported and discussed, relating to power conversion efficiency values.

High mobility, hole transport materials for highly efficient PEDOT:PSS replacement in inverted perovskite solar cells

Perovskite solar cells are one of the most promising photovoltaic technologies due to their rapid increase in power conversion efficiency (3.8% to 21.1%) in a very short period of time and the relative ease of their fabrication compared to traditional inorganic solar cells. One of the drawbacks of perovskite solar cells is their limited stability in non-inert atmospheres. In the inverted device configuration this lack of stability can be attributed to the inclusion of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) as the hole transporting layer. Herein we report the synthesis of two new triarylamine based hole transporting materials, synthesised from readily available starting materials. These new materials show increased power conversion efficiencies, of 13.0% and 12.1%, compared to PEDOT:PSS (10.9%) and exhibit increased stability achieving lifetimes in excess of 500 hours. Both molecules are solution processible at low temperatures and show potential for low cost, scalable production of large scale perovskite solar cells on flexible substrates.

Microwave-synthesized tin oxide nanocrystals for low-temperature solution-processed planar junction organo-halide perovskite solar cells

Tin oxide has been demonstrated to possess outstanding optoelectronic properties such as optical transparency and high electron mobility; therefore, it was successfully utilized as an electron transporting layer in various kinds of solar cells. In this study, for the first time, highly dispersible SnO2 nanoparticles were synthesized by a microwave-assisted non-aqueous sol–gel route in an organic medium. Ethanol dispersion of the as-prepared nanoparticles was used to cast a uniform thin layer of SnO2 without the aid of an aggregating agent and at low temperatures. Organohalide perovskite solar cells were fabricated using SnO2 as the electron transporting layer. Morphological and spectroscopic investigations, in addition to the good photoconversion efficiency obtained, evidenced that the nanoparticles synthesized by this route have optimal properties such as small size and crystallinity to form a continuous film. Furthermore, this method allows high reproducibility and scalability of the film deposition process.

2-(2,3,4,5,6-Pentafluorophenyl)-1H-benzo[d]imidazole, a fluorine-rich building block for the preparation of conjugated polymer donors for organic solar cell applications

We have introduced the pentafluorophenyl substituted benzimidazole as a building block of conjugated polymers for optoelectronic applications. We present the synthesis of a copolymer bearing fluorene as the comonomer. A detailed characterization of the novel material including structural, electrochemical and optical (using absorption, emission and time-resolved photoluminescence techniques) properties as well as computational modeling is described. The polymer exhibits highly efficient photoluminescence quenching when blended with fullerene derivatives (PCBM). The experimental results are compared with the alternating fluorene copolymer (APFO-3) in order to identify structure and property relations with the novel synthesized conjugated polymer. Early photovoltaic performance data are presented and compared with the well established APFO-3u2006:u2006PCBM material system.

Dithiopheneindenofluorene (TIF) Semiconducting Polymers with Very High Mobility in Field‐Effect Transistors

The charge-carrier mobility of organic semiconducting polymers is known to be enhanced when the energetic disorder of the polymer is minimized. Fused, planar aromatic ring structures contribute to reducing the polymer conformational disorder, as demonstrated by polymers containing the indacenodithiophene (IDT) repeat unit, which have both a low Urbach energy and a high mobility in thin-film-transistor (TFT) devices. Expanding on this design motif, copolymers containing the dithiopheneindenofluorene repeat unit are synthesized, which extends the fused aromatic structure with two additional phenyl rings, further rigidifying the polymer backbone. A range of copolymers are prepared and their electrical properties and thin-film morphology evaluated, with the co-benzothiadiazole polymer having a twofold increase in hole mobility when compared to the IDT analog, reaching values of almost 3 cm2 V-1 s-1 in bottom-gate top-contact organic field-effect transistors.