Martin Sahlberg

A monolithic device for solar water splitting based on series interconnected thin film absorbers reaching over 10% solar-to-hydrogen efficiency

Efficient production of hydrogen from solar energy is anticipated to be an important component in a future sustainable post-carbon energy system. Here we demonstrate that series interconnected absorbers in a PV-electrolysis configuration based on the compound semiconductor CIGS, CuInxGa1−xSe2, are a highly interesting concept for solar water splitting applications. The band gap energy of CIGS can be adjusted to a value close to optimum for efficient absorption of the solar spectrum, but is too low to drive overall water splitting. Therefore we connect three cells in series, into a monolithic device, which provides sufficient driving force for the full reaction. Integrated with a catalyst this forms a stable PV/photo-electrochemical device, which when immersed in water reaches over 10% solar-to-hydrogen efficiency for unassisted water splitting. The results show that series interconnected device concepts, which enable use of a substantial part of the solar spectrum, provide a simple route towards highly efficient water splitting and could be used also for other solar absorbers with similar electro-optical properties. We discuss how the efficiency could be increased for this particular device, as well as the general applicability of the concepts used in this work. We also briefly discuss advantages and disadvantages of photo-electrochemical cells in relation to PV-electrolysis with respect to our results.

Magnetocrystalline anisotropy and the magnetocaloric effect in Fe2P

Magnetic and magnetocaloric properties of high-purity, giant magnetocaloric polycrystalline and single-crystalline Fe2P are investigated. Fe2P displays a moderate magnetic entropy change, which spans over 70 K and the presence of strong magnetization anisotropy proves this system is not fully itinerant but displays a mix of itinerant and localized magnetism. The properties of pure Fe2P are compared to those of giant magnetocaloric (Fe,Mn)2(P,A) (where A=As, Ge, Si) compounds helping understand the exceptional characteristics shown by the latter, which are so promising for heat pump and energy conversion applications.

Strongly enhanced magnetic moments in ferromagnetic FeMnP0.5Si0.5

The compound FeMnP(0.5)Si(0.5) has been studied by magnetic measurements, Mossbauer spectroscopy, and electronic structure and total energy calculations. An unexpectedly high magnetic hyperfine fie ...

Order–disorder induced magnetic structures of FeMnP0.75Si0.25

We report on the synthesis and structural characterization of the magnetocaloric FeMnP0.75Si0.25 compound. Two types of samples (as quenched and annealed) were synthesized and characterized structu ...

The crystal and magnetic structure of the magnetocaloric compound FeMnP0.5Si0.5

The crystal and magnetic structure of the magnetocaloric compound FeMnP0.5Si0.5 has been studied by means of neutron and X-ray powder diffraction. Single phase samples of nominal composition FeMnP0 ...

Superior hydrogen storage in high entropy alloys.

Metal hydrides (MHx) provide a promising solution for the requirement to store large amounts of hydrogen in a future hydrogen-based energy system. This requires the design of alloys which allow for a very high H/M ratio. Transition metal hydrides typically have a maximum H/M ratio of 2 and higher ratios can only be obtained in alloys based on rare-earth elements. In this study we demonstrate, for the first time to the best of our knowledge, that a high entropy alloy of TiVZrNbHf can absorb much higher amounts of hydrogen than its constituents and reach an H/M ratio of 2.5. We propose that the large hydrogen-storage capacity is due to the lattice strain in the alloy that makes it favourable to absorb hydrogen in both tetrahedral and octahedral interstitial sites. This observation suggests that high entropy alloys have future potential for use as hydrogen storage materials.

Electrochemical fabrication and characterization of Cu/Cu2O multi-layered micro and nanorods in Li-ion batteries

Electrodes composed of freestanding nano- and microrods composed of stacked layers of copper and cuprous oxide have been fabricated using a straightforward one-step template-assisted pulsed galvanostatic electrodeposition approach. The approach provided precise control of the thickness of each individual layer of the high-aspect-ratio rods as was verified by SEM, EDS, XRD, TEM and EELS measurements. Rods with diameters of 80, 200 and 1000 nm were deposited and the influence of the template pore size on the structure and electrochemical performance of the conversion reaction based electrodes in lithium-ion batteries was investigated. The multi-layered Cu2O/Cu nano- and microrod electrodes exhibited a potential window of more than 2 V, which was ascribed to the presence of a distribution of Cu2O (and Cu, respectively) nanoparticles with different sizes and redox potentials. As approximately the same areal capacity was obtained independent of the diameter of the multi-layered rods the results demonstrate the presence of an electroactive Cu2O layer with a thickness defined by the time domain of the measurements. It is also demonstrated that while the areal capacity of the electrodes decreased dramatically when the scan rate was increased from 0.1 to 2 mV s(-1), the capacity remained practically constant when the scan rate was further increased to 100 mV s(-1). This behaviour can be explained by assuming that the capacity is limited by the lithium ion diffusion rate though the Cu2O layer generated during the oxidation step. The electrochemical performance of present type of 3-D multi-layered rods provides new insights into the lithiation and delithiation reactions taking place for conversion reaction materials such as Cu2O.

Phase diagram, structures and magnetism of the FeMnP1-xSix-system

The magnetic properties of the (Fe,Mn)2(P,Si)-system have been shown to be readily manipulated by small changes in composition. This study surveys the FeMnP1−xSix-system (0.00 ≤ x ≤ 1.00) reporting sample syntheses and investigations of crystallographic and magnetic properties using X-ray powder diffraction and magnetic measurements. Two single phase regions exist: the orthorhombic Co2P-type structure (x < 0.15) and the Fe2P-type structure (0.24 ≤ x < 0.50). Certain compositions have potential for use in magnetocaloric applications.

AlM2B2 (M = Cr, Mn, Fe, Co, Ni): a group of nanolaminated materials

Combining theory with experiments, we study the phase stability, elastic properties, electronic structure and hardness of layered ternary borides AlCr2B2, AlMn2B2, AlFe2B2, AlCo2B2, and AlNi2B2. We find that the first three borides of this series are stable phases, while AlCo2B2 and AlNi2B2 are metastable. We show that the elasticity increases in the boride series, and predict that AlCr2B2, AlMn2B2, and AlFe2B2 are more brittle, while AlCo2B2 and AlNi2B2 are more ductile. We propose that the elasticity of AlFe2B2 can be improved by alloying it with cobalt or nickel, or a combination of them. We present evidence that these ternary borides represent nanolaminated systems. Based on SEM measurements, we demonstrate that they exhibit the delamination phenomena, which leads to a reduced hardness compared to transition metal mono- and diborides. We discuss the background of delamination by analyzing chemical bonding and theoretical work of separation in these borides.

Mössbauer study of the magnetocaloric compound AlFe2B2

Mössbauer spectroscopy in the ferromagnetic AlFe2B2 reveals Tc=299 K and shows good agreement with magnetic measurements. The crystals are plate-shaped. The flakes are found from X-ray diffraction to be in the crystallographic ac-plane in the orthorhombic system. The axes of the principle electric field gradient tensor are, by symmetry, colinear with the crystal a-, b- and c-axes. By using information about the quadrupole splitting and line asymmetry in the paramagnetic regime together with the quadrupole shift of the resonance lines in the ferromagnetic regime the magnetic hyperfine field direction is found to be in the ab-plane having an angle =40° to the b-axis.