Meng-Qiang Zhao

Conductive two-dimensional titanium carbide ‘clay’ with high volumetric capacitance

Safe and powerful energy storage devices are becoming increasingly important. Charging times of seconds to minutes, with power densities exceeding those of batteries, can in principle be provided by electrochemical capacitors—in particular, pseudocapacitors. Recent research has focused mainly on improving the gravimetric performance of the electrodes of such systems, but for portable electronics and vehicles volume is at a premium. The best volumetric capacitances of carbon-based electrodes are around 300 farads per cubic centimetre; hydrated ruthenium oxide can reach capacitances of 1,000 to 1,500xa0farads per cubic centimetre with great cyclability, but only in thin films. Recently, electrodes made of two-dimensional titanium carbide (Ti3C2, a member of the ‘MXene’ family), produced by etching aluminium from titanium aluminium carbide (Ti3AlC2, a ‘MAX’ phase) in concentrated hydrofluoric acid, have been shown to have volumetric capacitances of over 300xa0farads per cubic centimetre. Here we report a method of producing this material using a solution of lithium fluoride and hydrochloric acid. The resulting hydrophilic material swells in volume when hydrated, and can be shaped like clay and dried into a highly conductive solid or rolled into films tens of micrometres thick. Additive-free films of this titanium carbide ‘clay’ have volumetric capacitances of up to 900xa0farads per cubic centimetre, with excellent cyclability and rate performances. This capacitance is almost twice that of our previous report, and our synthetic method also offers a much faster route to film production as well as the avoidance of handling hazardous concentrated hydrofluoric acid.

Flexible MXene/Carbon nanotube Composite Paper with High Volumetric Capacitance

Free-standing and flexible sandwich-like MXene/carbon nanotube (CNT) paper, composed of alternating MXene and CNT layers, is fabricated using a simple filtration method. These sandwich-like papers exhibit high volumetric capacitances, good rate performances, and excellent cycling stability when employed as electrodes in supercapacitors.

Flexible and conductive MXene films and nanocomposites with high capacitance

Significance Two-dimensional transition metal carbides (MXenes) offer a quite unique combination of excellent mechanical properties, hydrophilic surfaces, and metallic conductivity. In this first report (to our knowledge) on MXene composites of any kind, we show that adding polymer binders/spacers between atomically thin MXenes layers or reinforcing polymers with MXenes results in composite films that have excellent flexibility, good tensile and compressive strengths, and electrical conductivity that can be adjusted over a wide range. The volumetric capacitances of freestanding Ti3C2Tx MXene and its composite films exceed all previously published results. Owing to their mechanical strength and impressive capacitive performance, these films have the potential to be used for structural energy storage devices, electrochemical actuators, radiofrequency shielding, among other applications. MXenes, a new family of 2D materials, combine hydrophilic surfaces with metallic conductivity. Delamination of MXene produces single-layer nanosheets with thickness of about a nanometer and lateral size of the order of micrometers. The high aspect ratio of delaminated MXene renders it promising nanofiller in multifunctional polymer nanocomposites. Herein, Ti3C2Tx MXene was mixed with either a charged polydiallyldimethylammonium chloride (PDDA) or an electrically neutral polyvinyl alcohol (PVA) to produce Ti3C2Tx/polymer composites. The as-fabricated composites are flexible and have electrical conductivities as high as 2.2 × 104 S/m in the case of the Ti3C2Tx/PVA composite film and 2.4 × 105 S/m for pure Ti3C2Tx films. The tensile strength of the Ti3C2Tx/PVA composites was significantly enhanced compared with pure Ti3C2Tx or PVA films. The intercalation and confinement of the polymer between the MXene flakes not only increased flexibility but also enhanced cationic intercalation, offering an impressive volumetric capacitance of ∼530 F/cm3 for MXene/PVA-KOH composite film at 2 mV/s. To our knowledge, this study is a first, but crucial, step in exploring the potential of using MXenes in polymer-based multifunctional nanocomposites for a host of applications, such as structural components, energy storage devices, wearable electronics, electrochemical actuators, and radiofrequency shielding, to name a few.

Amine‐Assisted Delamination of Nb2C MXene for Li‐Ion Energy Storage Devices

2D Nb2CTx MXene flakes are produced using an amine-assisted delamination process. Upon mixing with carbon nanotubes and filtration, freestanding, flexible paper is produced. The latter exhibits high capacity and excellent stability when used as the electrode for Li-ion batteries and capacitors.

Pseudocapacitive Electrodes Produced by Oxidant-Free Polymerization of Pyrrole between the Layers of 2D Titanium Carbide (MXene)

Heterocyclic pyrrole molecules are in situ aligned and polymerized in the -absence of an oxidant between layers of the 2D Ti3C2Tx (MXene), resulting in high volumetric and gravimetric capacitances with capacitance retention of 92% after 25,000 cycles at a 100 mV s(-1) scan rate.

All-MXene (2D titanium carbide) solid-state microsupercapacitors for on-chip energy storage

On-chip energy storage is a rapidly evolving research topic, opening doors for the integration of batteries and supercapacitors at the microscale on rigid and flexible platforms. Recently, a new class of two-dimensional (2D) transition metal carbides and nitrides (so-called MXenes) has shown great promise in electrochemical energy storage applications. Here, we report the fabrication of all-MXene (Ti3C2Tx) solid-state interdigital microsupercapacitors by employing a solution spray-coating method, followed by a photoresist-free direct laser cutting method. Our prototype devices consisted of two layers of Ti3C2Tx with two different flake sizes. The bottom layer was stacked large-size MXene flakes (lateral dimensions of 3–6 μm) serving mainly as current collectors. The top layer was made of small-size MXene flakes (∼1 μm) with a large number of defects and edges as the electroactive layer responsible for energy storage. Compared to Ti3C2Tx micro-supercapacitors with platinum current collectors, the all-MXene devices exhibited a much lower contact resistance, higher capacitances and better rate-capabilities. Areal and volumetric capacitances of ∼27 mF cm−2 and ∼357 F cm−3, respectively, at a scan rate of 20 mV s−1 were achieved. The devices also demonstrated excellent cyclic stability, with 100% capacitance retention after 10u2006000 cycles at a scan rate of 50 mV s−1. This study opens up a plethora of possible designs for high-performance on-chip devices employing different chemistries, flake sizes and morphologies of MXenes and their heterostructures.

Synthesis of Carbon/Sulfur Nanolaminates by Electrochemical Extraction of Titanium from Ti 2 SC**

Herein we electrochemically and selectively extract Ti from the MAX phase Ti2SC to form carbon/sulfur (C/S) nanolaminates at room temperature. The products are composed of multi-layers of C/S flakes, with predominantly amorphous and some graphene-like structures. Covalent bonding between C and S is observed in the nanolaminates, which render the latter promising candidates as electrode materials for Li-S batteries. We also show that it is possible to extract Ti from other MAX phases, such as Ti3AlC2, Ti3SnC2, and Ti2GeC, suggesting that electrochemical etching can be a powerful method to selectively extract the M elements from the MAX phases, to produce AX layered structures, that cannot be made otherwise. The latter hold promise for a variety of applications, such as energy storage, catalysis, etc.

Hollow MXene Spheres and 3D Macroporous MXene Frameworks for Na‐Ion Storage

2D transition metal carbides and nitrides, named MXenes, are attracting increasing attentions and showing competitive performance in energy storage devices including electrochemical capacitors, lithium- and sodium-ion batteries, and lithium-sulfur batteries. However, similar to other 2D materials, MXene nanosheets are inclined to stack together, limiting the device performance. In order to fully utilize MXenes electrochemical energy storage capability, here, processing of 2D MXene flakes into hollow spheres and 3D architectures via a template method is reported. The MXene hollow spheres are stable and can be easily dispersed in solvents such as water and ethanol, demonstrating their potential applications in environmental and biomedical fields as well. The 3D macroporous MXene films are free-standing, flexible, and highly conductive due to good contacts between spheres and metallic conductivity of MXenes. When used as anodes for sodium-ion storage, these 3D MXene films exhibit much improved performances compared to multilayer MXenes and MXene/carbon nanotube hybrid architectures in terms of capacity, rate capability, and cycling stability. This work demonstrates the importance of MXene electrode architecture on the electrochemical performance and can guide future work on designing high-performance MXene-based materials for energy storage, catalysis, environmental, and biomedical applications.

Nanodiamonds suppress the growth of lithium dendrites

Lithium metal has been regarded as the future anode material for high-energy-density rechargeable batteries due to its favorable combination of negative electrochemical potential and high theoretical capacity. However, uncontrolled lithium deposition during lithium plating/stripping results in low Coulombic efficiency and severe safety hazards. Herein, we report that nanodiamonds work as an electrolyte additive to co-deposit with lithium ions and produce dendrite-free lithium deposits. First-principles calculations indicate that lithium prefers to adsorb onto nanodiamond surfaces with a low diffusion energy barrier, leading to uniformly deposited lithium arrays. The uniform lithium deposition morphology renders enhanced electrochemical cycling performance. The nanodiamond-modified electrolyte can lead to a stable cycling of lithium | lithium symmetrical cells up to 150 and 200u2009h at 2.0 and 1.0u2009mAu2009cm–2, respectively. The nanodiamond co-deposition can significantly alter the lithium plating behavior, affording a promising route to suppress lithium dendrite growth in lithium metal-based batteries.Lithium metal is an ideal anode material for rechargeable batteries but suffer from the growth of lithium dendrites and low Coulombic efficiency. Here the authors show that nanodiamonds serve as an electrolyte additive to co-deposit with lithium metal and suppress the formation of dendrites.

Enhanced Electrochemical Performance of Hydrous RuO2/Mesoporous Carbon Nanocomposites via Nitrogen Doping

Hydrous RuO2 nanoparticles have been uniformly deposited onto nitrogen-enriched mesoporous carbons (NMCs) via a facile hydrothermal method. The nitrogen doping in the carbon framework not only provides reversible pseudocapacitance but also guides uniform deposition of RuO2 nanoparticles. As a result, an extremely high specific capacitance of 1733 F/g per RuO2, comparable to the theoretic capacitance of RuO2, is reached when 4.3 wt % of RuO2·1.25H2O is loaded onto the NMCs. Systematic studies show that either nitrogen-free or excess nitrogen doping result in RuO2 clusters formation and worsen the electrochemical performances. With intermediate nitrogen and RuO2 content (8.1 wt % N, 29.6 wt % of RuO2·1.25H2O), the composites deliver excellent power performance and high specific capacitance (402 F/g) with reversible capacitive response at 500 mV/s. The unique properties of nitrogen in textual, morphological, and electrochemical aspects may also provide further understanding about the effects of nitrogen doping and metal oxide deposition on supercapacitor performance.