Meri J. Lundahl

Strength and Water Interactions of Cellulose I Filaments Wet-Spun from Cellulose Nanofibril Hydrogels.

Hydrogels comprising cellulose nanofibrils (CNF) were used in the synthesis of continuous filaments via wet-spinning. Hydrogel viscosity and spinnability, as well as orientation and strength of the spun filaments, were found to be strongly affected by the osmotic pressure as determined by CNF surface charge and solid fraction in the spinning dope. The tensile strength, Young’s modulus and degree of orientation (wide-angle X-ray scattering, WAXS) of filaments produced without drawing were 297 MPa, 21 GPa and 83%, respectively, which are remarkable values. A thorough investigation of the interactions with water using dynamic vapour sorption (DVS) experiments revealed the role of sorption sites in the stability of the filaments in wet conditions. DVS analysis during cycles of relative humidity (RH) between 0 and 95% revealed major differences in water uptake by the filaments spun from hydrogels of different charge density (CNF and TEMPO-oxidised CNF). It is concluded that the mechanical performance of filaments in the presence of water deteriorates drastically by the same factors that facilitate fibril alignment and, consequently, enhance dry strength. For the most oriented filaments, the maximum water vapour sorption at 95% RH was 39% based on dry weight.

Filaments with Affinity Binding and Wet Strength Can Be Achieved by Spinning Bifunctional Cellulose Nanofibrils

We demonstrate benzophenone (BP) conjugation via amine-reactive esters onto oxidized cellulosic fibers that were used as precursors, after microfluidization, of photoactive cellulose nanofibrils (CNF). From these fibrils, cellulose I filaments were synthesized by hydrogel spinning in an antisolvent followed by fast biradical UV cross-linking. As a result, the wet BP-CNF filaments retained extensively the original dry strength (a remarkable ∼80% retention). Thus, the principal limitation of these emerging materials was overcome (the wet tensile strength is typically <0.5% of the value measured in dry conditions). Subsequently, antihuman hemoglobin (anti-Hb) antibodies were conjugated onto residual surface carboxyl groups, making the filaments bifunctional for their active groups and properties (wet strength and bioactivity). Optical (surface plasmon resonance) and electroacoustic (quartz crystal microgravimetry) measurements conducted with the bifunctional CNF indicated effective anti-Hb conjugation (2.4 mg m-2), endowing an excellent sensitivity toward Hb targets (1.7 ± 0.12 mg m-2) and negligible nonspecific binding. Thus, the anti-Hb biointerface was deployed on filaments that captured Hb efficiently from aqueous matrices (confocal laser microscopy of FITC-labeled antibodies). Significantly, the anti-Hb biointerface was suitable for regeneration, while its sensitivity and selectivity in affinity binding can be tailored by application of blocking copolymers. The developed bifunctional filaments based on nanocellulose offer great promise in detection and affinity binding built upon 1D systems, which can be engineered into other structures for rational use of material and space.

Asymmetric cellulose nanocrystals: thiolation of reducing end groups via NHS–EDC coupling

Abstract Cellulose nanocrystals (CNC) were functionalized in aqueous media at the reducing, aldehyde ends of cellulose. CNC oxidation to produce carboxyl groups was followed by carbodiimide-mediated reaction to install thiol groups. The selectivity and extent of thiolation at the reducing ends was qualitatively confirmed by imaging (transmission electron microscopy) silver nanoparticles that tagged the CNC termini and by X-ray photoelectron spectroscopy, respectively. The adsorption of thiolated CNC onto gold surfaces as well as the viscoelastic property of the formed adlayer was investigated by using quartz crystal microgravimetry. The thiolated CNC chemisorbed on the surfaces were further analyzed for surface density and distribution by using atomic force microscopy. Overall we introduce a facile, mild asymmetric thiolation procedure as an efficient alternative to conventional reductive amination.

Surface Structuring and Water Interactions of Nanocellulose Filaments Modified with Organosilanes toward Wearable Materials

Colloidal dispersions of cellulose nanofibrils (CNFs) are viable alternatives to cellulose II dissolutions used for filament spinning. The porosity and water vapor affinity of CNF filaments make them suitable for controlled breathability. However, many textile applications also require water repellence. Here, we investigated the effects of postmodification of wet-spun CNF filaments via chemical vapor deposition (CVD). Two organosilanes with different numbers of methyl substituents were considered. Various surface structures were achieved, either as continuous, homogeneous coating layers or as three-dimensional, hairy-like assemblies. Such surface features reduced the surface energy, which significantly affected the interactions with water. Filaments with water contact angles of up to 116° were obtained, and surface energy measurements indicated the possibility of developing amphiphobicity. Dynamic vapor sorption and full immersion experiments were carried out to inquire about the interactions with water, whether in the liquid or gas forms. Mechanical tests revealed that the wet strength of the modified filaments were almost 3 times higher than that of the unmodified precursors. The hydrolytic and mechanical stabilities of the adsorbed layers were also revealed. Overall, our results shed light on the transformation of aqueous dispersions of CNFs into filaments that are suited for controlled interactions with water via concurrent hydrolysis and condensation reactions in CVD, while maintaining the moisture buffering capacity and breathability of related structures.

Absorbent Filaments from Cellulose Nanofibril Hydrogels through Continuous Coaxial Wet Spinning

A continuous and scalable method for the wet spinning of cellulose nanofibrils (CNFs) is introduced in a core/shell configuration. Control on the interfacial interactions was possible by the choice of the shell material and coagulant, as demonstrated here with guar gum (GG) and cellulose acetate (CA). Upon coagulation in acetone, ethanol, or water, GG and CA formed supporting polymer shells that interacted to different degrees with the CNF core. Coagulation rate was shown to markedly influence the CNF orientation in the filament and, as a result, its mechanical strength. The fastest coagulation noted for the CNF/GG core/shell system in acetone led to an orientation index of ∼0.55 (Herman’s orientation parameter of 0.40), Young’s modulus of ∼2.1 GPa, a tensile strength of ∼70 MPa, and a tenacity of ∼8 cN/tex. The system that underwent the slowest coagulation rate (CNF/GG in ethanol) displayed a limited CNF orientation but achieved an intermediate level of mechanical resistance, owing to the strong core/shell interfacial affinity. By using CA as the supporting shell, it was possible to spin CNF into filaments with high water absorption capacity (43 g water/g dry filament). This was explained by the fact that water (used as the coagulant for CA) limited the densification of the CNF core structure, yielding filaments with high accessible area and pore density.