Mike Pivnenko

Demonstration of Multi-Casting in a 1 × 9 LCOS Wavelength Selective Switch

A multi-functional 1 × 9 wavelength selective switch based on liquid crystal on silicon (LCOS) spatial light modulator technology and anamorphic optics was tested at a channel spacing of 100 and 200 GHz, including dynamic data measurements on both single beam deflection and multi-casting to two ports. The multi-casting holograms were optimized using a modified Gerchberg-Saxton routine to design the core hologram, followed by a simulated annealing routine to reduce crosstalk at non-switched ports. The effect of clamping the magnitude of phase changes between neighboring pixels during optimization was investigated, with experimental results for multi-casting to two ports resulting in a signal insertion loss of -7.6 dB normalized to single port deflection, a uniformity of ±0.6%, and a worst case crosstalk of -19.4 dB, which can all be improved further by using a better anti-reflection coating on the LCOS SLM coverplate and other measures.

High-birefringence nematic liquid crystal for broadband THz applications

ABSTRACT Liquid crystals (LCs) have been studied extensively in the visible range for their dielectric tunability, and the characterisation in the terahertz (THz) range has gained increasing interest due to the need for active THz modulation and switching devices. In this paper, we use THz time-domain spectroscopy to measure the frequency-dependent birefringence and the absorption coefficient of a number of commercial and non-commercial nematic LCs, including E7, BL037, MDA-98-1602, LCMS-107, GT3-23001 and 1825, over a range of bias voltages at room temperature. Furthermore, several basic components of LC mixture are analysed to establish their contributions to birefringence and theoretical model is used to fit the absorption spectra. The large tunability and low loss measured for a range of samples show that the LCs are useful tunable dielectrics for compact, efficient and broadband THz devices. GRAPHICAL ABSTRACT

Diffraction based phase compensation method for phase-only liquid crystal on silicon devices in operation

A method to measure the optical response across the surface of a phase-only liquid crystal on silicon device using binary phase gratings is described together with a procedure to compensate its spatial optical phase variation. As a result, the residual power between zero and the minima of the first diffraction order for a binary grating can be reduced by more than 10 dB, from -15.98 dB to -26.29 dB. This phase compensation method is also shown to be useful in nonbinary cases. A reduction in the worst crosstalk by 5.32 dB can be achieved when quantized blazed gratings are used.

High quality micro liquid crystal phase lenses for full resolution image steering in auto-stereoscopic displays

The use of pixel-level tunable liquid crystal (LC) lenses to steer the images shown on a flat panel display in full resolution for auto-stereoscopic applications was proposed. Micro lenticular LC lenses of different full widths ranging from 40 to 140 µm were designed and fabricated with laser patterned transparent ITO electrodes as narrow as 10 µm in width and two LC materials of high birefringence. Optical characterization of the lenses showed consistent parabolic phase profiles closely matched to that of ideal lenses. A proof-of-concept device with an array of tunable micro LC lenses each covers two sub-pixels of different colors was fabricated and applied on a standard computer monitor to confirm its capability of sub-pixel-level image steering.

Colorimetric-based detection of TNT explosives using functionalized silica nanoparticles.

This proof-of-concept study proposes a novel sensing mechanism for selective and label-free detection of 2,4,6-trinitrotoluene (TNT). It is realized by surface chemistry functionalization of silica nanoparticles (NPs) with 3-aminopropyl-triethoxysilane (APTES). The primary amine anchored to the surface of the silica nanoparticles (SiO2-NH2) acts as a capturing probe for TNT target binding to form Meisenheimer amine–TNT complexes. A colorimetric change of the self-assembled (SAM) NP samples from the initial green of a SiO2-NH2 nanoparticle film towards red was observed after successful attachment of TNT, which was confirmed as a result of the increased separation between the nanoparticles. The shift in the peak wavelength of the reflected light normal to the film surface (λpeak) and the associated change of the peak width were measured, and a merit function taking into account their combined effect was proposed for the detection of TNT concentrations from 10−12 to 10−4 molar. The selectivity of our sensing approach is confirmed by using TNT-bound nanoparticles incubated in AptamerX, with 2,4-dinitrotoluene (DNT) and toluene used as control and baseline, respectively. Our results show the repeatable systematic color change with the TNT concentration and the possibility to develop a robust, easy-to-use, and low-cost TNT detection method for performing a sensitive, reliable, and semi-quantitative detection in a wide detection range.

Uniform and fast switching of window-size smectic A liquid crystal panels utilising the field gradient generated at the fringes of patterned electrodes

ABSTRACT A method to enable smectic A (SmA) liquid crystal (LC) devices to switch uniformly and hence fast from the clear state to a scattered state is presented. It will allow the reduction of the switching time for a SmA LC panel of 1 × 1 m2 changing from a clear state to a fully scattered state by more than three orders to a few tens of milliseconds. Experimental results presented here reveal that SmA LC scattering initiates from the nucleated LC defects at the field gradient of the applied electric field usually along the edges of the panel electrode and grows laterally to spread over a panel, which takes a long time if the panel size is large. By patterning the electrodes in use, it is possible to create a large number of field gradient sites near the electrode discontinuities, resulting in a uniform and fast switching over the whole panel and the higher the pattern density the shorter the panel switching time. For the SmA LC panels used here, the ITO transparent electrodes are patterned by laser ablation and photolithography. It is shown that the defect nucleation time is much shorter than the growth time of the scattered region, hence it is possible to use the density of the field gradient sites to control the uniformity and switching time of a panel. Furthermore, the patterned SmA panels have a lower switching voltage than that of the non-patterned ones in general. Graphical Abstract

A compensation method for the full phase retardance nonuniformity in phase-only liquid crystal on silicon spatial light modulators

A simple and efficient compensation method for the full correction of both the anisotropic and isotropic nonuniformity of the light phase retardance in a liquid crystal (LC) layer is presented. This is achieved by accurate measurement of the spatial variation of the LC layers thickness with the help of a calibrated liquid crystal wedge, rather than solely relying on the light intensity profile recorded using two crossed polarizers. Local phase retardance as a function of the applied voltage is calculated with its LC thickness and a set of reference data measured from the intensity of the reflected light using two crossed polarizers. Compensation of the corresponding phase nonuniformity is realized by applying adjusted local voltage signals for different grey levels. To demonstrate its effectiveness, the proposed method is applied to improve the performance of a phase-only liquid crystal on silicon (LCOS) spatial light modulator (SLM). The power of the first diffraction order measured with the binary phase gratings compensated by this method is compared with that compensated by the conventional crossed-polarizer method. The results show that the phase compensation method proposed here can increase the dynamic range of the first order diffraction power significantly from 15~21 dB to over 38 dB, while the crossed-polarizer method can only increase it to 23 dB.

Advanced die-level assembly techniques and quality analysis for phase-only liquid crystal on silicon devices:

This work was supported by State Key Laboratory of Precision Measurement Technology and Instruments, Tsinghua University. It was also supported by National Natural Science Foundation of China (61307077), Beijing Natural Science Foundation (4144076), China Postdoctoral Science Foundation (2013M530613), the UK Engineering and Physical Sciences Research Council (EPSRC) through the Platform Grant in liquid crystal photonics (EP/F00897X/1) and the Cambridge Integrated Knowledge Centre (CIKC) through projects PASSBACK and PASSBACK3.

A tunable wideband microstrip bandstop filter based on liquid crystal materials

A compact liquid crystal (LC) based tunable wideband microstrip bandstop filter (BSF) is presented in this paper. To realize a compact size and wide stopband bandwidth, a double-stub bending structure was designed. The BSF stopbands can be tuned by applying a voltage between 0-20 V to regulate the LC dielectric permittivity. A tunability >7% and 3dB bandwidth > 3 GHz and 2.5 GHz for the first and second stopbands respectively were achieved. The rejection level was higher than 41 dB. Such a LC based BSF device with a high tunability, wide stopband bandwidth, low driving voltage and compact size are useful in a wide range of applications.