Miles A. Sakwa-Novak

Effect of Amine Surface Coverage on the Co-Adsorption of CO2 and Water: Spectral Deconvolution of Adsorbed Species

Three primary amine materials functionalized onto mesoporous silica with low, medium, and high surface amine coverages are prepared and evaluated for binary CO2/H2O adsorption under dilute conditions. Enhancement of amine efficiency due to humid adsorption is most pronounced for low surface amine coverage materials. In situ FT-IR spectra of adsorbed CO2 on these materials suggest this enhancement may be associated with the formation of bicarbonate species during adsorption on materials with low surface amine coverage, though such species are not observed on high surface coverage materials. On the materials with the lowest amine loading, bicarbonate is observed on longer time scales of adsorption, but only after spectral contributions from rapidly forming alkylammonium carbamate species are removed. This is the first time that direct evidence for bicarbonate formation, which is known to occur in liquid aqueous amine solutions, has been presented for CO2 adsorption on solid amine adsorbents.

Steam Induced Structural Changes of a Poly(ethylenimine) Impregnated γ-Alumina Sorbent for CO2 Extraction from Ambient Air

Poly(ethylenimine) (PEI) impregnated mesoporous γ-alumina sorbents are utilized for CO2 adsorption from dry and humid simulated ambient air, and the sorbents are regenerated under an environment of flowing steam for times ranging from 5 min to 24 h of continuous exposure. The sorbents are compared on the basis of equilibrium CO2 capacities from simulated air at 400 ppm of CO2, 50% relative humidity, and 30 °C as well as their physiochemical characterization by means of X-ray diffraction (XRD), (27)Al NMR spectroscopy, IR spectroscopy, Raman spectroscopy, N2 physisorption, and elemental analysis. The sorbents retain better than 90% of the initial equilibrium capacity of ∼1.7 mmol/g at steam exposure times up to 12 h; however, PEI leaching reduced the capacity of the sorbent to 0.66 mmol/g after 24 h of continuous treatment. It is demonstrated that the γ-alumina support partially hydrates to form a boehmite crystal phase at steam times of 90 min and longer but that this phase transition occurs predominately between 90 min and 12 h of steam treatment, slowing at longer times of 12 and 24 h of treatment. Evidence is presented to suggest that the presence of boehmite on the sorbent surface does not significantly alter the amine efficiency of impregnated PEI. The collected results suggest that γ-alumina/PEI composite materials are promising sorbents for CO2 capture from ambient air with regeneration in flowing steam.

Linking CO2 Sorption Performance to Polymer Morphology in Aminopolymer/Silica Composites through Neutron Scattering

Composites of poly(ethylenimine) (PEI) and mesoporous silica are effective, reversible adsorbents for CO2, both from flue gas and in direct air-capture applications. The morphology of the PEI within the silica can strongly impact the overall carbon capture efficiency and rate of saturation. Here, we directly probe the spatial distribution of the supported polymer through small-angle neutron scattering (SANS). Combined with textural characterization from physisorption analysis, the data indicate that PEI first forms a thin conformal coating on the pore walls, but all additional polymer aggregates into plug(s) that grow along the pore axis. This model is consistent with observed trends in amine-efficiency (CO2/N binding ratio) and pore size distributions, and points to a trade-off between achieving high chemical accessibility of the amine binding sites, which are inaccessible when they strongly interact with the silica, and high accessibility for mass transport, which can be hampered by diffusion through PEI plugs. We illustrate this design principle by demonstrating higher CO2 capacity and uptake rate for PEI supported in a hydrophobically modified silica, which exhibits repulsive interactions with the PEI, freeing up binding sites.

Role of Additives in Composite PEI/Oxide CO2 Adsorbents: Enhancement in the Amine Efficiency of Supported PEI by PEG in CO2 Capture from Simulated Ambient Air

Supported amines are promising candidate adsorbents for the removal of CO2 from flue gases and directly from ambient air. The incorporation of additives into polymeric amines such as poly(ethylenimine) (PEI) supported on mesoporous oxides is an effective strategy to improve the performance of the materials. Here, several practical aspects of this strategy are addressed with regards to direct air capture. The influence of three additives (CTAB, PEG200, PEG1000) was systematically explored under dry simulated air capture conditions (400 ppm of CO2, 30 °C). With SBA-15 as a model support for poly(ethylenimine) (PEI), the nature of the additive induced heterogeneities in the deposition of organic on the interior and exterior of the particles, an important consideration for future scale up to practical systems. The PEG200 additive increased the observed thermodynamic performance (∼60% increase in amine efficiency) of the adsorbents regardless of the PEI content, while the other molecules had less positive effects. A threshold PEG200/PEI value was identified at which the diffusional limitations of CO2 within the materials were nearly eliminated. The threshold PEG/PEI ratio may have physical origin in the interactions between PEI and PEG, as the optimal ratio corresponded to nearly equimolar OH/reactive (1°, 2°) amine ratios. The strategy is shown to be robust to the characteristics of the host support, as PEG200 improved the amine efficiency of PEI when supported on two varieties of mesoporous γ-alumina with PEI.

Poly(ethylenimine)-Functionalized Monolithic Alumina Honeycomb Adsorbents for CO2 Capture from Air.

The development of practical and effective gas-solid contactors is an important area in the development of CO2 capture technologies. Target CO2 capture applications, such as postcombustion carbon capture and sequestration (CCS) from power plant flue gases or CO2 extraction directly from ambient air (DAC), require high flow rates of gas to be processed at low cost. Extruded monolithic honeycomb structures, such as those employed in the catalytic converters of automobiles, have excellent potential as structured contactors for CO2 adsorption applications because of the low pressure drop imposed on fluid moving through the straight channels of such structures. Here, we report the impregnation of poly(ethylenimine) (PEI), an effective aminopolymer reported commonly for CO2 separation, into extruded monolithic alumina to form structured CO2 sorbents. These structured sorbents are first prepared on a small scale, characterized thoroughly, and compared with powder sorbents with a similar composition. Despite consistent differences observed in the filling of mesopores with PEI between the monolithic and powder sorbents, their performance in CO2 adsorption is similar across a range of PEI contents. A larger monolithic cylinder (1 inch diameter, 4 inch length) is evaluated under conditions closer to those that might be used in large-scale applications and shows a similar performance to the smaller monoliths and powders tested initially. This larger structure is evaluated over five cycles of CO2 adsorption and steam desorption and demonstrates a volumetric capacity of 350 molCO2  m-3monolith and an equilibration time of 350 min under a 0.4 m s(-1) linear flow velocity through the monolith channels using 400 ppm CO2 in N2 as the adsorption gas at 30 °C. This volumetric capacity surpasses that of a similar technology considered previously, which suggested that CO2 could be removed from air at an operating cost as low as

Post-grafting amination of alkyl halide-functionalized silica for applications in catalysis, adsorption, and 15N NMR spectroscopy.

100 per ton.

Design of Aminopolymer Structure to Enhance Performance and Stability of CO2 Sorbents: Poly(propylenimine) vs Poly(ethylenimine)

An anhydrous synthesis of aminosilica materials from alkyl halide-functionalized mesoporous SBA-15 silica by post-grafting amination is introduced for applications in CO2 adsorption, cooperative catalysis, and (15)N solid-state NMR spectroscopy. The synthesis is demonstrated to convert terminal alkyl halide-functionalized silica materials containing Cl, Br, and I to primary alkylamines using anhydrous ammonia in a high-pressure reactor. The benefits of the post-grafting amination procedure include (i) use of anhydrous isotopically labeled ammonia, (15)NH3, to create aminosilica materials that can be investigated using (15)N solid-state NMR to elucidate potential intermediates and surface species in CO2 adsorption processes and catalysis, (ii) similar CO2 uptake in experiments extracting CO2 from dry simulated air experiments, and (iii) improved activity in acid-base bifunctional catalysis compared to traditional amine-grafted materials. The effects of the type of halide, the initial halide loading, and the total reaction time on the conversion of the halides to primary amines are explored. Physical and chemical characterizations of the materials show that the textural properties of the silica are unaffected by the reaction conditions and that quantitative conversion to primary amines is achieved even at short reaction times and high initial alkyl halide loadings. Additionally, preliminary (15)N solid-state NMR experiments indicate formation of nitrogen-containing species and demonstrate that the synthesis can be used to create materials useful for investigating surface species by NMR spectroscopy. The differences between the materials prepared via post-grafting amination vs traditional aminosilane grafting are attributed to the slightly increased spacing of the amines synthesized by amination because the alkylhalosilanes are initially better spaced on the silica surface after grafting, whereas the aminosilanes likely cluster to a greater extent when grafted on the silica surface. A slight increase in amine spacing allows for more effective amine-silanol interactions in cooperative catalysis without reducing the amine efficiency in CO2 uptake under the conditions used here.

Interrogating the Carbon and Oxygen K-Edge NEXAFS of a CO2-Dosed Hyperbranched Aminosilica.

Studies on aminopolymer/oxide composite materials for direct CO2 capture from air have often focused on the prototypical poly(ethylenimine) (PEI) as the aminopolymer. However, it is known that PEI will oxidatively degrade at elevated temperatures. This degradation has been ascribed to the presence of secondary amines, which, when oxidized, lose their CO2 capture capacity. Here, we demonstrate the use of small molecule poly(propylenimine) (PPI) in linear and dendritic architectures supported in silica as adsorbent materials for direct CO2 capture from air. Regardless of amine loading or aminopolymer architecture, the PPI-based sorbents are found to be more efficient for CO2 capture than PEI-based sorbents. Moreover, PPI is found to be more resistant to oxidative degradation than PEI, even while containing secondary amines, as supported by FTIR, NMR, and ESI-MS studies. These results suggest that PPI-based CO2 sorbents may allow for longer sorbent working lifetimes due to an increased tolerance to sorbent regeneration conditions and suggest that the presence of secondary amines may not mean that all aminopolymers will oxidatively degrade.

Unraveling the Dynamics of Aminopolymer/Silica Composites.

Using near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, we shed light on the nature of the interaction between CO2 and the amine moieties in a hyperbranched aminosilica (HAS) material, a porous aminosilica composite with great potential for postcombustion carbon capture applications. We show that after dosing a pristine (annealed) HAS sample with CO2, the C K-edge NEXAFS spectrum presents a new π* resonance at 289.9 eV, which can be attributed to the formation of a C═O (carbonyl) bond. Additional analyses of the O K-edge using model samples containing carbamate, carbonate, and bicarbonate functional groups as reference demonstrate a carbamate bonding mechanism for the chemical adsorption of CO2 by the HAS material under the conditions employed. These findings show the capability of the C and O K-edge NEXAFS technique to identify CO2-adsorbate species despite the high concentration of C and O atoms inherently present in the sample (prior to CO2 dosing) and the significant similarities between the possible adsorbates.

Linking Silica Support Morphology to the Dynamics of Aminopolymers in Composites

The structure and dynamics of a model branched polymer was investigated through molecular dynamics simulations and neutron scattering experiments. The polymer confinement, monomer concentration, and solvent quality were varied in the simulations and detailed comparisons between the calculated structural and dynamical properties of the unconfined polymer and those confined within an adsorbing and nonadsorbing cylindrical pore, representing the silica based structural support of the composite, were made. The simulations show a direct relationship in the structure of the polymer and the nonmonotonic dynamics as a function of monomer concentration within an adsorbing cylindrical pore. However, the nonmonotonic behavior disappears for the case of the branched polymer within a nonadsorbing cylindrical pore. Overall, the simulation results are in good agreement with quasi-elastic neutron scattering (QENS) studies of branched poly(ethylenimine) in mesoporous silica (SBA-15) of comparable size, suggesting an approach that can be a useful guide for understanding how to tune porous polymer composites for enhancing desired dynamical and structural behavior targeting carbon dioxide adsorption.