Mingde Du

High Detectivity Graphene-Silicon Heterojunction Photodetector.

A graphene/n-type silicon (n-Si) heterojunction has been demonstrated to exhibit strong rectifying behavior and high photoresponsivity, which can be utilized for the development of high-performance photodetectors. However, graphene/n-Si heterojunction photodetectors reported previously suffer from relatively low specific detectivity due to large dark current. Here, by introducing a thin interfacial oxide layer, the dark current of graphene/n-Si heterojunction has been reduced by two orders of magnitude at zero bias. At room temperature, the graphene/n-Si photodetector with interfacial oxide exhibits a specific detectivity up to 5.77 × 10(13) cm Hz(1/2) W(-1) at the peak wavelength of 890 nm in vacuum, which is highest reported detectivity at room temperature for planar graphene/Si heterojunction photodetectors. In addition, the improved graphene/n-Si heterojunction photodetectors possess high responsivity of 0.73 A W(-1) and high photo-to-dark current ratio of ≈10(7) . The current noise spectral density of the graphene/n-Si photodetector has been characterized under ambient and vacuum conditions, which shows that the dark current can be further suppressed in vacuum. These results demonstrate that graphene/Si heterojunction with interfacial oxide is promising for the development of high detectivity photodetectors.

Highly Narrowband Photomultiplication Type Organic Photodetectors

Filterless narrowband response organic photodetectors (OPDs) present a great challenge due to the broad absorption range of organic semiconducting materials. The reported narrowband response OPDs also suffer from low external quantum efficiency (EQE) in the desired response window and low rejection ratio. Here, we report highly narrowband photomultiplication (PM) type OPDs based on P3HT:PC71BM (100:1, wt/wt) as active layer without an optical filter. The full width at half-maximum (fwhm) of the PM-type OPDs can be well retained less than 30 nm under different biases. Meanwhile, the champion EQE and rejection ratio approach 53 500% and 2020 at -60 V bias, respectively. The small fwhm should be attributed to the sharp absorption edge of active layer with small amount of PC71BM. The PM phenomenon is attributed to hole tunneling injection from the external circuit assisted by trapped electron in PC71BM near the Al electrode under light illumination. These highly narrowband PM-type OPDs should have great potential applications in sensitively detecting specific wavelength light and be blind to light outside of the desired response window.

Templated synthesis of TiO2 nanotube macrostructures and their photocatalytic properties

Controlled synthesis of hierarchically assembled titanium dioxide (TiO2) nanostructures is important for practical applications in environmental purification and solar energy conversion. We present here the fabrication of interconnected TiO2 nanotubes as a macroscopic bulk material by using a porous carbon nanotube (CNT) sponge as a template. The basic idea is to uniformly coat an amorphous titania layer onto the CNT surface by the infiltration of a TiO2 precursor into the sponge followed by a subsequent hydrolysis process. After calcination, the CNTs are completely removed and the titania is simultaneously crystallized, which results in a porous macrostructure composed of interconnected anatase TiO2 nanotubes. The TiO2 nanotube macrostructures show comparable photocatalytic activities to commercial products (AEROXIDE TiO2 P25) for the degradation of rhodamine B (RhB). Moreover, the TiO2 nanotube macrostructures can be settled and separated from water within 12 h after photocatalysis, whereas P25 remains suspended in solution after weeks. Thus the TiO2 nanotube macrostructures offer the advantage of easy catalyst separation and recycle and can be a promising candidate for wastewater treatment.

Blown-Bubble Assembly and in Situ Fabrication of Sausage-like Graphene Nanotubes Containing Copper Nanoblocks.

We use a blown-bubble method to assemble Cu nanowires and in situ fabricate graphene-based one-dimensional heterostructures, including versatile sausage-like configurations consisting of multilayer graphene nanotubes (GNTs) filled by single or periodically arranged Cu nanoblocks (CuNBs). This is done by first assembling Cu nanowires among a polymer-based blown-bubble film (BBF) and then growing graphene onto the nanowire substrate using the polymer matrix as a solid carbon source by chemical-vapor deposition. The formation of sausage-like GNT@CuNB nanostructures is due to the partial melting and breaking of embedded Cu nanowires during graphene growth, which is uniquely related to our BBF process. We show that the GNT skin significantly slows the oxidation process of CuNBs compared with that of bare Cu nanowires, and the presence of stuffed CuNBs also reduces the linear resistance along the GNTs. The large-scale assembled graphene-based heterostructures achieved by our BBF method may have potential applications in heterojunction electronic devices and high-stability transparent conductive electrodes.

Multiscale Hierarchical Design of a Flexible Piezoresistive Pressure Sensor with High Sensitivity and Wide Linearity Range

Flexible piezoresistive pressure sensors have been attracting wide attention for applications in health monitoring and human-machine interfaces because of their simple device structure and easy-readout signals. For practical applications, flexible pressure sensors with both high sensitivity and wide linearity range are highly desirable. Herein, a simple and low-cost method for the fabrication of a flexible piezoresistive pressure sensor with a hierarchical structure over large areas is presented. The piezoresistive pressure sensor consists of arrays of microscale papillae with nanoscale roughness produced by replicating the lotus leafs surface and spray-coating of graphene ink. Finite element analysis (FEA) shows that the hierarchical structure governs the deformation behavior and pressure distribution at the contact interface, leading to a quick and steady increase in contact area with loads. As a result, the piezoresistive pressure sensor demonstrates a high sensitivity of 1.2 kPa-1 and a wide linearity range from 0 to 25 kPa. The flexible pressure sensor is applied for sensitive monitoring of small vibrations, including wrist pulse and acoustic waves. Moreover, a piezoresistive pressure sensor array is fabricated for mapping the spatial distribution of pressure. These results highlight the potential applications of the flexible piezoresistive pressure sensor for health monitoring and electronic skin.

Flexible and biocompatible nanopaper-based electrode arrays for neural activity recording

Advances in neural electrode technologies can have a significant impact on both fundamental and applied neuroscience. Here, we report the development of flexible and biocompatible neural electrode arrays based on a nanopaper substrate. Nanopaper has important advantages with respect to polymers such as hydrophilicity and water wettability, which result in significantly enhanced biocompatibility, as confirmed by both in vitro viability assays and in vivo histological analysis. In addition, nanopaper exhibits high flexibility and good shape stability. Hence, nanopaper-based neural electrode arrays can conform to the convoluted cortical surface of a rat brain and allow stable multisite recording of epileptiform activity in vivo. Our results show that nanopaper-based electrode arrays represent promising candidates for the flexible and biocompatible recording of the neural activity.

Simultaneous surface and depth neural activity recording with graphene transistor-based dual-modality probes

Subdural surface and penetrating depth probes are widely applied to record neural activities from the cortical surface and intracortical locations of the brain, respectively. Simultaneous surface and depth neural activity recording is essential to understand the linkage between the two modalities. Here, we develop flexible dual-modality neural probes based on graphene transistors. The neural probes exhibit stable electrical performance even under 90° bending because of the excellent mechanical properties of graphene, and thus allow multi-site recording from the subdural surface of rat cortex. In addition, finite element analysis was carried out to investigate the mechanical interactions between probe and cortex tissue during intracortical implantation. Based on the simulation results, a sharp tip angle of π/6 was chosen to facilitate tissue penetration of the neural probes. Accordingly, the graphene transistor-based dual-modality neural probes have been successfully applied for simultaneous surface and depth recording of epileptiform activity of rat brain in vivo. Our results show that graphene transistor-based dual-modality neural probes can serve as a facile and versatile tool to study tempo-spatial patterns of neural activities.