Muhanad M. Hatamleh

Fracture resistance of teeth restored with different post systems: in vitro study

OBJECTIVESnThe objective of this study was to investigate fracture resistance and mode of failure of teeth restored with different prefabricated post systems.nnnSTUDY DESIGNnThirty teeth were collected, sectioned 15 mm from the apex, root canal prepared, and randomly allocated into 3 groups as follows: glass fiber posts (group 1), carbon fiber posts (group 2), and Radix-Anchor titanium posts (group 3). Teeth were then restored with a composite core and tested using a universal testing machine at 10 mm/min cross-head speed. Mode of failure was identified as either reparable or irreparable (catastrophic).nnnRESULTSnMean values of fracture forces (N) for teeth restored with Radix posts (571.6) were statistically significantly higher than teeth restored with either carbon fiber (420.6) or glass fiber posts (393.9). There were 86.67% of fractures that were catastrophic in nature.nnnCONCLUSIONSnTeeth restored with Radix-titanium posts were more resistant to fracture than those restored with either carbon or glass fiber posts. Most of the fracture modes were catastrophic in nature.

Correction of facial and mandibular asymmetry using a computer aided design/computer aided manufacturing prefabricated titanium implant.

AbstractPatients with significant craniofacial asymmetry may have functional problems associated with their occlusion and aesthetic concerns related to the imbalance in soft and hard tissue profiles. This report details a case of facial asymmetry secondary to left mandible angle deficiency due to undergoing previous radiotherapy. We describe the correction of the bony deformity using computer aided design/computer aided manufacturing custom-made titanium onlay using novel direct metal laser sintering. The direct metal laser sintering onlay proved a very accurate operative fit and showed a good aesthetic correction of the bony defect with no reported complications postoperatively. It is a useful low-morbidity technique, and there is no resorption or associated donor-site complications.

Simultaneous Computer-Aided Design/Computer-Aided Manufacture Bimaxillary Orthognathic Surgery and Mandibular Reconstruction Using Selective-Laser Sintered Titanium Implant.

This patient report describes simultaneous bimaxillary orthognathic surgery and mandibular reconstruction by means of three-dimensional (3D) planning, 3D printed biocompatible surgical wafers, and 3D selective-laser sintered titanium implant. A 26-year-old male patient presented with a left mandibular defect secondary to trauma. The whole body of the mandible on the left hand side was deficient with a narrow connection with the remaining left condyle. He had undergone orthodontic treatment for 18 months and was ready to undergo bimaxillary orthognathic surgery. Advanced cranio-maxillofacial software was used in processing his cone beam computer tomography scan data, and e-casts of his upper and lower dental arches. Bimaxillary surgery was planned with Le Fort 1 maxillary impaction and mandibular advancement to achieve a class 1 incisor relationship. Intermediate and final surgical wafers were designed following the planned movements and printed using biocompatible resin. The deficient left side of the mandible was reconstructed by means of mirror imaging the contra-lateral right side into the deficient left side with the aim of restoring normal facial symmetry. Biomedical software was then used in designing a reconstruction plate that connected the condylar head and the mandible following the planned bimaxillary surgery and mandibular continuity symmetry reconstruction. The plate was printed in titanium following state-of the-art selective laser sintering technology. The bimaxillary surgery and mandibular reconstruction were done simultaneously as planned along with an iliac-crest bone graft. This patient confirms the advantages of 3D computer-aided design/computer-aided manufacture technologies in optimizing clinical outcomes for cranio-maxillofacial reconstruction, especially when conducting two simultaneous clinical procedures.

Improved Construction of Auricular Prosthesis by Digital Technologies.

Abstract Implant-retained auricular prostheses are a successful prosthetic treatment option for patients who are missing their ear(s) due to trauma, oncology, or birth defects. The prosthetic ear is aesthetically pleasing, composed of natural looking anatomical contours, shape, and texture along with good color that blends with surrounding existing skin. These outcomes can be optimized by the integration of digital technologies in the construction process. This report describes a sequential process of reconstructing a missing left ear by digital technologies. Two implants were planned for placement in the left mastoid region utilizing specialist biomedical software (Materialise, Belgium). The implant positions were determined underneath the thickest portion (of anti-helix area) left ear that is virtually simulated by means of mirror imaging of the right ear. A surgical stent recording the implant positions was constructed and used in implant fixtures placement. Implants were left for eight weeks, after which they were loaded with abutments and an irreversible silicone impression was taken to record their positions. The right existing ear was virtually segmented using the patient CT scan and then mirror imaged to produce a left ear, which was then printed using 3D printer (Z Corp, USA). The left ear was then duplicated in wax which was fitted over the defect side. Then, it was conventionally flasked. Skin color was digitalized using spectromatch skin color system (London, UK). The resultant silicone color was mixed as prescribed and then packed into the mold. The silicone was cured conventionally. Ear was trimmed and fitted and there was no need for any extrinsic coloring. The prosthetic ear was an exact match to the existing right ear in shape, skin color, and orientation due to the great advantages of technologies employed. Additionally, these technologies saved time and provided a base for reproducible results regardless of operator.

Shear bond strength of self-adhesive resin cements to base metal alloy

STATEMENT OF PROBLEMnMany self-adhesive cements have been introduced in the past few years, with little or no data regarding their clinical performance. This study investigated the shear bond strength of some recently introduced self-adhesive resin cements.nnnPURPOSEnThe purpose of this study was to evaluate the shear bond strength of self-adhesive and conventional resin-based cements to a base metal alloy.nnnMATERIAL AND METHODSnFour groups (10-12 each) that comprised 3 self-adhesive cements (SmartCem2; RelyX Unicem; seT SDI) and a conventional resin-based cement (RelyX ARC) were tested. Cylindrical cement specimens (diameter, 3 mm; height, 3 mm) were applied to nickel-free base metal alloy (Sheradent) disks with a diameter of 12 mm, and the surface was treated with airborne-particle abrasion of 50 μm aluminum oxide. The metal disks were fixed in brass molds specifically designed for the shear bond test device. Test specimens were incubated at 37°C for 24 hours and then the shear bond was tested with a Zwick Roll testing machine at a 0.8 mm/min cross-head speed. In addition, bond failures were investigated and categorized as adhesive, cohesive, or mixed. Shear bond strengths were calculated by dividing the maximum debonding force over the cross-sectional area of each specimen. One-way ANOVA and the Tukey (honestly significant difference) post hoc test were used to test statistical significant differences among the groups (α=.05).nnnRESULTSnStatistical analysis showed significant differences among different resin cements (F=14.34, P<.001). The highest mean shear bond strength was observed for SmartCem2 (14.18 MPa), and the lowest was reported for seT (3.52 MPa). The observed failure mode in all the materials was adhesive in nature, which occurred at the resin-metal interface.nnnCONCLUSIONSnThe early bond strength of self-adhesive resin cements varied significantly among the tested materials. SmartCem2 showed the highest bond strength, which was 4 times the strength observed for seT SDI.

Improved Virtual Planning for Bimaxillary Orthognathic Surgery.

Conventional model surgery planning for bimaxillary orthognathic surgery can be laborious, time-consuming and may contain potential errors; hence three-dimensional (3D) virtual orthognathic planning has been proven to be an efficient, reliable, and cost-effective alternative. In this report, the 3D planning is described for a patient presenting with a Class III incisor relationship on a Skeletal III base with pan facial asymmetry complicated by reverse overjet and anterior open bite. A combined scan data of direct cone beam computer tomography and indirect dental scan were used in the planning. Additionally, a new method of establishing optimum intercuspation by scanning dental casts in final occlusion and positioning it to the composite-scans model was shown. Furthermore, conventional model surgery planning was carried out following in-house protocol. Intermediate and final intermaxillary splints were produced following the conventional method and 3D printing. Three-dimensional planning showed great accuracy and treatment outcome and reduced laboratory time in comparison with the conventional method. Establishing the final dental occlusion on casts and integrating it in final 3D planning enabled us to achieve the best possible intercuspation.

Novel Treatment Planning of Hemimandibular Hyperplasia by the Use of Three-Dimensional Computer-Aided-Design and Computer-Aided-Manufacturing Technologies

RATIONALE AND AIMnHemimandibular hyperplasia is characterized by an obvious overgrowth in the size of the mandible on one side, which can extend up to the midline causing facial asymmetry. Surgical resection of the overgrowth depends heavily on the skill and experience of the surgeon. This report describes a novel methodology of applying three-dimensional computer-aided-design and computer-aided-manufacturing principles in improving the outcome of surgery in 2 mandibular hyperplasia patients.nnnMETHODOLOGYnBoth patients had their cone beam computer tomography (CBCT) scan performed. CMF Pro Plan software (v. 2.1) was used to process the scan data into virtual 3-dimensional models of the maxilla and mandible. Head tilt was adjusted manually by following horizontal reference. Facial asymmetry secondary to mandibular hypertrophy was obvious on frontal and lateral views. Simulation functions were followed including mirror imaging of the unaffected mandibular side into the hyperplastic side and position was optimized by translation and orientation functions. Reconstruction of virtual symmetry was assessed and checked by running 3-dimensional measurements. Then, subtraction functions were used to create a 3-dimensional template defining the outline of the lower mandibular osteotomy needed. Precision of mandibular teeth was enhanced by amalgamating the CBCT scan with e-cast scan of the patient lower teeth. 3-Matic software (v. 10.0) was used in designing cutting guide(s) that define the amount of overgrowth to be resected. The top section of the guide was resting on the teeth hence ensuring stability and accuracy while positioning it. The guide design was exported as an .stl file and printed using in-house 3-dimensional printer in biocompatible resin.nnnCONCLUSIONnThree-dimensional technologies of both softwares (CMF Pro Plan and 3-Matic) are accurate and reliable methods in the diagnosis, treatment planning, and designing of cutting guides that optimize surgical correction of hemimandibular hyperplasia at timely and cost-effect manner.Rationale and Aim: Hemimandibular hyperplasia is characterized by an obvious overgrowth in the size of the mandible on one side, which can extend up to the midline causing facial asymmetry. Surgical resection of the overgrowth depends heavily on the skill and experience of the surgeon. This report describes a novel methodology of applying three-dimensional computer-aided-design and computer-aided-manufacturing principles in improving the outcome of surgery in 2 mandibular hyperplasia patients. Methodology: Both patients had their cone beam computer tomography (CBCT) scan performed. CMF Pro Plan software (v. 2.1) was used to process the scan data into virtual 3-dimensional models of the maxilla and mandible. Head tilt was adjusted manually by following horizontal reference. Facial asymmetry secondary to mandibular hypertrophy was obvious on frontal and lateral views. Simulation functions were followed including mirror imaging of the unaffected mandibular side into the hyperplastic side and position was optimized by translation and orientation functions. Reconstruction of virtual symmetry was assessed and checked by running 3-dimensional measurements. Then, subtraction functions were used to create a 3-dimensional template defining the outline of the lower mandibular osteotomy needed. Precision of mandibular teeth was enhanced by amalgamating the CBCT scan with e-cast scan of the patient lower teeth. 3-Matic software (v. 10.0) was used in designing cutting guide(s) that define the amount of overgrowth to be resected. The top section of the guide was resting on the teeth hence ensuring stability and accuracy while positioning it. The guide design was exported as an .stl file and printed using in-house 3-dimensional printer in biocompatible resin. Conclusion: Three-dimensional technologies of both softwares (CMF Pro Plan and 3-Matic) are accurate and reliable methods in the diagnosis, treatment planning, and designing of cutting guides that optimize surgical correction of hemimandibular hyperplasia at timely and cost-effect manner.

Survey of Ocular Prosthetics Rehabilitation in the United Kingdom, Part 1: Anophthalmic Patients’ Aetiology, Opinions, and Attitudes

Purpose: Ocular prostheses are constructed to aid cosmetic, functional, and psychological rehabilitation of anophthalmic patients. Part-1 of this study aimed to evaluate anophthalmic patients’ opinions, attitudes, and experience about aspects related to their postfit ocular prostheses. Methods: One hundred sixty questionnaires were delivered to anophthalmic patients inquiring about different information such as age, gender, occupation, eye-loss cause, prosthesis type, prosthesis-wearing frequency, prosthesis-cleaning frequency, and problems encountered. A total of 126 questionnaires were returned (response rate was 78.8%). Data was analyzed using SPSS software (Pu200a<0.05). Results: The patients were 74 males and 52 females (57.55 yearsu200a±u200a17.57). Almost 50% of the patients lost their eye due to trauma that was the highest among other causes (Pu200a<0.05). High proportion clean their prosthesis daily (37.4%) which was the highest among other cleaning regimes (Pu200a<0.05). Almost 30.3% experienced having problems with their prosthetic eye. Patients who clean their prosthetic eye every 6 months have experienced more problems (Pu200a<0.05). Majority of patients wear their prosthetic eyes 24 hours (92%) (Pu200a<0.05). Half of patients who received a prosthetic eye for the first time experienced problems with it (Pu200a<0.05) such as excess discharge (45%), infection (25%), and soreness (20%). However, the problems were independent of prosthesis-type (Pu200a>0.05). Conclusions: Trauma is the most common cause of anophthalmic patients in the North-West of England. Anophthalmic patients are likely to experience problems with their prosthetic eye if they have lost their natural eye due to disease; it is their first prosthesis; or if they clean it once every 6 months.

Survey of Ocular Prosthetics Rehabilitation in the United Kingdom, Part 2: Anophthalmic Patients’ Satisfaction and Acceptance

Aim: Ocular prostheses are integral for anophthalmic patients. Part 1 of this study reported that patients’ aetiology, opinions, and attitudes significantly affected their prosthetic eyes experience. Part 2 investigates the patient satisfaction and acceptance in light of some of the aetiological demographics reported in Part 1. Methodology: One hundred sixty questionnaires were delivered to anophthalmic patients attending oculoplastic clinic. Etiological aspects presented in the questionnaire were disseminated in part 1. Patient satisfaction was assessed through 8 closed-end statements reflecting aspects concerning patients views on prosthesis comfort and appearance; patients expectations, self-esteem, and perception; and cooperation with ocularist. Each statement had 3 categories as agree, moderately agree, and disagree. A total of 126 questionnaires were returned (response rate was 78.8%). Data was analyzed using SPSS software. Association coefficients and correlations between variables were also analyzed. Results: Total number of responses for the 8 statements was 888, averaging of 111 (expected 126) respondent per statement. Overall, 95.4% of our patients agreed with all satisfaction statements presented echoing very high satisfaction rate with their ocular prosthetics. Having an eye replacement that covers the defect is associated with high satisfaction among patients regardless of ocular prosthetic type. Patient acceptance of prosthesis in relation to employment status was high but not the same among the different categories (Pu200a>u200a0.05). High satisfaction with ocular prosthetics was prevalent among both genders, but there were no statistically significant differences in percentages of agreement in all statements (Pu200a>u200a0.05). Satisfaction and acceptance with ocular prosthetics was the same among all age groups of 12 to 85 years old (Pu200a>u200a0.05). Conclusions: The patient satisfaction is associated with the interplay of different variables that is related to ocular prosthesis design and its ability to disguise disfigurement (ie, prosthesis shape, resemblance to existing contra-lateral eye, etc.); patients themselves (ie, gender, age, occupation, marital status, etc); and psychological well-being and social support provided. Anophthalmic patients of the north west of England are significantly happy with their ocular prosthetic rehabilitation and support they receive from their regional hospital. Ocular prosthetics enhances their psychological well-being and social interaction and factors like patients’ sex, age, employment status, and type of ocular prosthesis have no effect on their acceptance and satisfaction.