Norio Ishizuka

Monolithic silica columns for high-efficiency chromatographic separations

Studies on the structural and chromatographic properties of monolithic silica columns were reviewed. Monolithic silica columns prepared from tetraalkoxysilane by a sol-gel method showed high efficiency and high permeability on the basis of the small-sized silica skeletons, large-sized through-pores, and resulting through-pore size/skeleton size ratios much larger than those found in a particle-packed column.

Monolithic silica columns for HPLC, micro-HPLC, and CEC

Two types of monolithic silica columns derivatized to form an ODS phase, one prepared in a fused silica capillary (SR-FS) and the other prepared in a mold and clad with an engineering plastic (poly-ether-ether-ketone) (SR-PEEK), were evaluated. The column efficiency and pressure drop were compared with those of a column packed with 5-μm ODS-silica particles and of an ODS-silica monolith prepared in a mold and wrapped with PTFE tubing (SR-PTFE). SR-FS gave a lower pressure drop than a column packed with 5-μm particles by a factor of 20, and a plate height of 20 μm at a linear velocity below 1 mm/s. SR-PEEK showed higher flow-resistance than the other monolithic silica columns, but they still showed a minimum plate height of 8-10 μm and a lower pressure drop than popular commercial columns packed with 5-μm particles. The evaluation of SR-FS columns in a CEC mode showed much higher efficiency than in a pressure-driven mode.

Monolithic silica columns with various skeleton sizes and through-pore sizes for capillary liquid chromatography

Reduction of through-pore size and skeleton size of a monolithic silica column was attempted to provide high separation efficiency in a short time. Monolithic silica columns were prepared to have various sizes of skeletons (approximately 1-2 microm) and through-pores (approximately 2-8 microm) in a fused-silica capillary (50-200 microm I.D.). The columns were evaluated in HPLC after derivatization to C18 phase. It was possible to prepare monolithic silica structures in capillaries of up to 200 microm I.D. from a mixture of tetramethoxysilane and methyltrimethoxysilane. As expected, a monolithic silica column with smaller domain size showed higher column efficiency and higher pressure drop. High external porosity (> 80%) and large through-pores resulted in high permeability (K = 8 x 10(-14) -1.3 x 10(-12) m2) that was 2-30 times higher than that of a column packed with 5-mirom silica particles. The monolithic silica columns prepared in capillaries produced a plate height of about 8-12 microm with an 80% aqueous acetonitrile mobile phase at a linear velocity of 1 mm/s. Separation impedance, E, was found to be as low as 100 under optimum conditions, a value about an order of magnitude lower than reported for conventional columns packed with 5-microm particles. Although a column with smaller domain size generally resulted in higher separation impedance and the lower total performance, the monolithic silica columns showed performance beyond the limit of conventional particle-packed columns under pressure-driven conditions.

Monolithic silica columns for high-efficiency separations by high-performance liquid chromatography.

Generation of a large number of theoretical plates was attempted by capillary HPLC. Monolithic silica columns having small skeletons (ca. 2 microm) and large through-pores (ca. 8 microm) were prepared by a sol-gel method in a fused-silica capillary (50 microm I.D.), and derivatized to C18 phase by on-column reaction. High external porosity (>80%) and large through-pores resulted in high permeability (K= 1.2 x 10(-2) m2). The monolithic silica column in the capillary produced a plate height of about 12 microm in 80% acetonitrile at a linear velocity of 1 mm/s. Separation impedance, E value, was found to be as low as 200, that was about an order of magnitude lower than reported values for conventional columns packed with 5 microm particles. Reproducibility of preparation within +/- 15% was obtained for column efficiency and for pressure drop. It was possible to generate 100,000 plates by using a 130-cm column at very low pressure (<7 kg/cm2). A considerable decrease in column efficiency was observed at high linear velocity, and for solutes with large retention factors due to the slow mobile-phase mass transfer in the large through-pores. The monolithic silica columns, however, showed performance beyond the limit of conventional particle-packed columns in HPLC under favorable conditions.

Tailoring Mesopores in Monolithic Macroporous Silica for HPLC

Mesopore formation in silica gels having continuous macropores has been investigated. The macroporous wet silica gel prepared by the sol-gel process including phase separation was aged in a basic solvent making use of hydrolysis of urea in a closed condition. The mesopore structure was finally obtained by subsequent evaporation drying of solvent and heat-treatment at 600°C for 2 h. The dissolution-reprecipitation kinetics at the interfaces between wet gel skeletons and an external solvent affected the size and volume of pores formed within the skeletons. Below 120°C, mesopores suitable for various chromatographic applications have been formed typically within 24 h. On the other hand, at 200°C, the pore size attained the macropore dimensions (>50 nm), and the whole macroporous morphology was significantly modified.

Performance of an octadecylsilylated continuous porous silica column in polypeptide separations

Abstract A continuous porous silica rod column prepared by an alkoxy-derived sol-gel method in the presence of a water-soluble organic polymer was tested in the reversed-phase acetonitrile–water linear gradient elution of polypeptides with molecular masses of up to 80 000. The silica rod having the through-pore size of 1.1 μm and silica skeleton size of 0.7 μm with mesopore size of 26 nm was used. The gradient time and the linear velocity of the mobile phase were varied and the resolution was examined in terms of peak capacity. The resolution with the silica rod was less affected by the gradient steepness and the mobile phase velocity. The results indicate that the silica rod column could reduce the separation time by a factor of 3 or more compared to the conventional column packed with 5 μm silica particles.

Chromatographic characterization of macroporous monolithic silica prepared via sol-gel process

Abstract A continuous porous silica monolith prepared by the sol-gel process including phase separation was aged in a basic solvent making use of hydrolysis of urea to prepare extended mesopore structures for chromatographic applications. The dissolution–reprecipitation kinetics at the interfaces between wet gel skeletons and an external solvent affected the size and volume of pores formed within the skeletons. At above 200°C, the pore size attained the macropore dimensions (>50 nm). The results of chromatography indicate that the monolithic silica column with wide mesopore could reduce the separation time compared to the conventional column packed with 5 μm silica particle.

New monolithic capillary columns with well-defined macropores based on poly(styrene-co-divinylbenzene).

Macroporous polymer monoliths based on poly(styrene-co-divinylbenzene) with varied styrene/divinylbenzene ratios have been prepared by organotellurium-mediated living radical polymerization. The well-defined cocontinuous macroporous structure can be obtained by polymerization-induced spinodal decomposition, and the pore structures are controlled by adjusting the starting composition. The separation efficiency of small molecules (alkylbenzenes) in the obtained monoliths has been evaluated in the capillary format by high-performance liquid chromatography (HPLC) under the isocratic reversed-phase mode. Baseline separations of these molecules with a low pressure drop (∼2 MPa) have been achieved because of the well-defined macropores and to the less-heterogeneous cross-linked networks.

Preparation and Chromatographic Application of Macroporous Silicate in a Capillary

Continuous macroporous silica gel networks were prepared in a fused silica capillary, and evaluated in reversed-phase liquid chromatography. Under pressure-driven conditions, considerable dependence of column efficiency on the linear velocity of the mobile phase was observed in spite of the small size of the silica skeletons. A major source of band broadening in the pressure-driven mode was found in the A-term of van Deemter equation. The performance of the continuous silica capillary column in the electro-driven mode was much better than that in the pressure-driven mode.

Enhanced Sequence Coverage in Tryptic Fragment Analysis by Two-Dimensional HPLC/MS Using a Monolithic Silica Capillary Column

The HPLC/MS system, in which a monolithic silica capillary column is directly connected to an electronspray-ionization mass spectrometer, showed superior performance at high mobile phase linear velocity. A two-dimensional (2D) HPLC/MS system was established, using an ion-exchange particle-packed capillary column at the first dimension and a monolithic silica capillary column at the second dimension. In an analysis of tryptic fragments from bovine serum albumin, an 81% sequence coverage, obtained by the 2D-HPLC/MS system, increased by 23% as compared to a 1D-HPLC/MS system. This 2D-HPLC/MS system using a monolithic silica capillary column should be useful for enhancing sequence coverage of tryptic fragments in proteomics.