Paavo A. Penttilä

Amorphous Characteristics of an Ultrathin Cellulose Film

Swelling behavior and rearrangements of an amorphous ultrathin cellulose film (20 nm thickness) exposed to water and subsequently dried were investigated with grazing incidence X-ray diffraction, neutron reflectivity, atomic force microscopy, and surface energy calculations obtained from contact angle measurements. The film swelled excessively in water, doubling its thickness, but shrunk back to the original thickness upon water removal. Crystallinity (or amorphousness) and morphology remained relatively unchanged after the wetting/drying cycle, but surface free energy increased considerably (ca. 15%) due to an increase in its polar component, that is, the hydrophilicity of the film, indicating that rearrangements occurred during the films exposure to water. Furthermore, stability of the films in aqueous NaOH solution was investigated with quartz crystal microbalance with dissipation monitoring. The films were stable at 0.0001 M NaOH but already 0.001 M NaOH partially dissolved the film. The surprising susceptibility to dissolve in dilute NaOH was hypothetically attributed to the lack of hierarchical morphology in the amorphous film.

Xylan as limiting factor in enzymatic hydrolysis of nanocellulose

The role of xylan as a limiting factor in the enzymatic hydrolysis of cellulose was studied by hydrolysing nanocellulose samples prepared by mechanical fibrillation of birch pulp with varying xylan content. Analyzing the nanocelluloses and their hydrolysis residues with dynamic FT-IR spectroscopy revealed that a certain fraction of xylan remained tightly attached to cellulose fibrils despite partial hydrolysis of xylan with xylanase prior to pulp fibrillation and that this fraction remained in the structure during the hydrolysis of nanocellulose with cellulase mixture as well. Thus, a loosely bound fraction of xylan was predicted to have been more likely removed by purified xylanase. The presence of loosely bound xylan seemed to limit the hydrolysis of crystalline cellulose, indicated by an increase in cellulose crystallinity and by preserved crystal width measured with wide-angle X-ray scattering. Removing loosely bound xylan led to a proportional hydrolysis of xylan and cellulose with the cellulase mixture.

Changes in Submicrometer Structure of Enzymatically Hydrolyzed Microcrystalline Cellulose

To understand the limitations occurring during enzymatic hydrolysis of cellulosic materials in renewable energy production, we used wide-angle X-ray scattering (WAXS), small-angle X-ray scattering (SAXS), X-ray microtomography, and transmission electron microscopy (TEM) to characterize submicrometer changes in the structure of microcrystalline cellulose (Avicel) digested with the Trichoderma reesei enzyme system. The microtomography measurements showed a clear decrease in particle size in scale of tens of micrometers. In all the TEM pictures, similar elongated and partly ramified structures were observed, independent of the hydrolysis time. The SAXS results of rewetted samples suggested a slight change in the structure in scale of 10-20 nm, whereas the WAXS results confirmed that the degree of crystallinity and the crystal sizes remained unchanged. This indicates that the enzymes act on the surface of cellulose bundles and are unable to penetrate into the nanopores of wet cellulose.

Nanofibrillated cellulose/carboxymethyl cellulose composite with improved wet strength

In this paper, nanofibrillated cellulose/carboxymethyl cellulose (CMC) composite films were prepared using tape casting. The obtained transparent films showed shear induced partial alignment of fibrils along the casting direction, resulting in birefringence in cross polarized light. The carboxyl groups of CMC could be further utilized to create ionic crosslinking by treatment with glycidyl trimethyl ammonium chloride (GTMA). The GTMA treated composite films had improved mechanical properties both in wet and dry state. The chemical composition and morphologies of composites were analyzed with X-ray photoelectron spectroscopy, elemental analysis, scanning electron microscopy and wide-angle X-ray scattering.

Structural Changes in Microcrystalline Cellulose in Subcritical Water Treatment

Subcritical water is a high potential green chemical for the hydrolysis of cellulose. In this study microcrystalline cellulose was treated in subcritical water to study structural changes of the cellulose residues. The alterations in particle size and appearance were studied by scanning electron microscopy (SEM) and those in the degree of polymerization (DP) and molar mass distributions by gel permeation chromatography (GPC). Further, changes in crystallinity and crystallite dimensions were quantified by wide-angle X-ray scattering and (13)C solid-state NMR. The results showed that the crystallinity remained practically unchanged throughout the treatment, whereas the size of the remaining cellulose crystallites increased. Microcrystalline cellulose underwent significant depolymerization in subcritical water. However, depolymerization leveled off at a relatively high degree of polymerization. The molar mass distributions of the residues showed a bimodal form. We infer that cellulose gets dissolved in subcritical water only after extensive depolymerization.

Enhancement of ionic liquid-aided fractionation of birchwood. Part 1: autohydrolysis pretreatment

Ionic liquid-cosolvent systems have been proposed as selective solvent media for lignocellulosic materials. We present the ionic liquid-aided fractionation of silver birch (Betula pendula) combined with an autohydrolysis pretreatment. Contrary to untreated birchwood meal, autohydrolyzed birchwood meal reveals quantitative dissolution in 1-ethyl-3-methylimidazolium acetate and distinct separation into the individual wood polymers upon regeneration in acetone/water. The process yields two main fractions, a cellulose-rich precipitate with a residual lignin content of 13–15% and another virtually pure lignin fraction. No cellulose yield loss is observed during the ionic liquid processing step. A comprehensive mass balance of the process, including insoluble material, wash waters, and soluble residues, is provided. The product fractions are characterised for their chemical compositions, molar mass distributions and structural characteristics by Klason lignin and sugar analysis, 13C NMR, GPC and WAXS. The study investigates the effects of wood particle size and autohydrolysis intensity on fractionation efficiency and selectivity.

The effect of drying method on the properties and nanoscale structure of cellulose whiskers

Cellulose whiskers were prepared from wood- and cotton-based microcrystalline cellulose and dried by two methods: freeze-drying or air-drying. The effect of drying method on the properties and structure of the whiskers were studied. Furthermore, the influence of the source of cellulose on the nanoscale structure was investigated. Drying method was observed to slightly influence the thermal stability of cellulose whiskers, whereas the char residue varied significantly depending on the drying process performed. Small- and wide-angle X-ray scattering and solid state nuclear magnetic resonance spectroscopy were used to examine the crystallinity and nanoscale structure of the dried whiskers. It was observed that the crystal structure and crystallinity of cellulose whiskers remained during all treatments, whereas their nanoscale structure was significantly influenced by drying method, neutralization, and source of cellulose. Relationships between thermal behavior and nanoscale structure were reported and discussed.

X-ray scattering and microtomography study on the structural changes of never-dried silver birch, European aspen and hybrid aspen during drying

Abstract The impact of drying on the structure of the never-dried hardwood cell wall was studied at nanometer level by means of wide- and small-angle X-ray scattering (WAXS, SAXS), and at micrometer level by X-ray microtomography (μCT). Never-dried silver birch, European aspen and hybrid aspen samples were measured by WAXS in situ during drying in air. The samples included juvenile and mature wood, as well as normal and tension wood to allow comparison of the effects of different matrix compositions and microfibril angles. The deformations of cellulose crystallites and amorphous components of the cell wall were detected as changes in the cellulose reflections 200 and 004 and amorphous halo in the WAXS patterns. Especially, the width of the reflection 004, corresponding to the cellulose chain direction, increased due to drying in all the samples, indicating an increase of strain and disorder of the chains. Also, the cellulose unit cell shrank 0.2–0.3% during drying in this direction in all the samples except in hybrid aspen tension wood. According to the SAXS results of silver birch, the distance between micro-fibrils decreased during drying. It was detected by μCT that the mean cross-sectional maximum width of the parenchymatous rays decreased from that of never-dried to air-dried birch by roughly 16%.

Effects of pressurized hot water extraction on the nanoscale structure of birch sawdust

Pressurized hot water extraction with a flow-through system was used to extract hemicelluloses and lignin from birch sawdust. The structure of the extraction residue was studied on various levels. Molecular mass distributions were determined with gel permeation chromatography and the crystal structure of cellulose was characterized using wide-angle X-ray scattering (WAXS). Information on the short-range order of cellulose microfibrils and on the nanoscale pore structure was obtained with small-angle X-ray scattering (SAXS), and the micrometre scale cellular morphology was imaged with X-ray microtomography. The pressurized hot water treatment was observed to increase the lateral width of cellulose crystallites, determined with WAXS, whereas a possible small decrease in the crystallinity of cellulose compared to native wood was detected. The molecular mass of cellulose remained at a relatively high level. According to the SAXS results, a tighter lateral association of cellulose microfibrils was observed in the extracted samples, which possibly led to opening of pores between bundles of microfibrils, as indicated by an increased specific surface area. A reduction in the thickness of the fibre cell walls was evidenced by X-ray microtomography.

Cellulose degradation in alkaline media upon acidic pretreatment and stabilisation

The present study reports on a revised kinetic model for alkaline degradation of cellulose accounting for primary peeling/stopping reactions as well as for alkaline hydrolysis followed by secondary peeling. Oxalic acid pretreated cotton linters was utilised as the model substrate for the prehydrolysis-soda anthraquinone process. The main emphasis was investigating the effect of end-group stabilising additives such as sodium borohydride (BH), anthraquinone (AQ), and anthraquinone-2-sulphonic acid sodium salt (AQS) on the rates of the yield loss reactions. BH and AQS ensured a cellulose yield gain of 13% and 11%, respectively, compared to the reference. Both stabilisation agents decreased the content of the reducing end groups in the samples, while in the case of AQS stabilisation a 25% increase in carboxyl group content compared to the reference was also observed. As expected, the addition of end group stabilisers resulted in a significant decrease in the peeling-to-stopping rate constants ratio.