Paola Torricelli

Strontium-substituted hydroxyapatite coatings synthesized by pulsed-laser deposition: In vitro osteoblast and osteoclast response

The increasing interest in strontium incorporation into biomaterials for hard tissue repair is justified by the growing evidence of its beneficial effect on bone. We successfully synthesized hydroxyapatite (HA) thin films with different extents of strontium substitution for calcium (0, 1, 3 or 7 at.%) by pulsed-laser deposition. The coatings displayed a granular surface and a good degree of crystallinity, which slightly diminished as strontium content increased. Osteoblast-like MG63 cells and human osteoclasts were cultured on the thin films up to 21 days. MG63 cells grown on the strontium-doped HA coatings displayed normal morphology, good proliferation and increased values of the differentiation parameters, whereas the number of osteoclasts was negatively influenced by the presence of strontium. The positive effect of the ion on bone cells was particularly evident in the case of coatings deposited from HA at relatively high strontium contents (3-7%), where significantly increased values of alkaline phosphatase activity, osteocalcin, type I collagen and osteoprotegerin/TNF-related activation-induced cytokine receptor ratio, and considerably reduced values of osteoclast proliferation, were observed.

In vitro and in vivo behaviour of Ca- and P-enriched anodized titanium

The influence of different surface preparations on titanium biocompatibility and bone integration was evaluated. Commercially grade 2 titanium rods (diameter 2 mm, length: 3 mm), vacuum annealed and hydrofluoric acid etched was selected for its promising surface characteristics to achieve good direct osseointegration. Some rods were surface modified by Anodic Spark Discharge anodization and a thin layer (approximately 5 microm) of amorphous TiO2 containing Ca and P (Ti/AM) was obtained. Some of the Ti/AM specimens underwent a further hydrothermal treatment to produce a thin outermost layer (approximately 1 microm) of hydroxyapatite (Ti/AM/HA). Cytotoxicity tests (direct contact: ISO 10993-5) showed good cytocompatibility for all tested samples. Ti and tissue culture substrate + DMEM control, respectively, were associated with a significant higher proportion of attached cells than Ti/AM and Ti/AM/HA (P < 0.0005), but this was in the normal range of 10-20% of unattached cells for cytocompatible materials. Histomorphometric analysis conducted on samples inserted in the cancellous bone of distal femoral epiphysis of Sprague-Dawley rats gave the following results at 4 and 8 weeks: Affinity index (AI%) data proving the surface osteconductive properties of non-anodized acid etched Ti (AI-4 weeks: 67.1 +/- 17.0%; AI-8 weeks: 74.8 +/- 11.5%). Ti/AM samples showed the lowest values (AI-4 weeks: 45.8 +/- 15.9%; AI-8 weeks: 68.5 +/- 13.6%) while the best performances of the Ti/AM/HA samples (AI-4 weeks: 60.4 +/- 21.8%; AI-8 weeks: 79.5 + 9.37%) indicated that hydroxyapatite allowed a higher bone to implant contact respect to Ti only. Further investigations should be performed in order to better understand the mechanism of observed in vitro behaviour and to achieve information on long-term osseointegration process.

Hyaluronic acid hydrogel in the treatment of osteoarthritis

In order to overcome the problem of rapid clearance of the polysaccharide hyaluronic acid (Hyal) in the treatment of osteoarthritis (OA), a 50% cross-linked Hyal hydrogel (Hyal 50%) was synthesised. The 50% refers to the amount of COOH groups of the polysaccharide involved in the cross-linking reaction. i.e. 50% of the total amount. The rheological behaviour of the Hyal 50% hydrogel, and in particular the possibility to inject it through a needle, was studied. The results obtained demonstrated that the hydrogel injected through the needle still behaved like a gel, although it showed a reduction of the dynamic moduli. The most appropriate sterilisation technique for this kind of hydrogel was also evaluated. Liophilised Hyal 50% samples were sterilised by steam, Ethylene Oxide (EtO) and gamma-rays. EtO and gamma-rays did not modify the characteristics of the hydrogel in terms of swellability and morphology. Lastly, the in vivo effect of Hyal 50% hydrogel in the treatment of chondral defect in rabbit knee was also studied. The results obtained showed the Hyal 50% injections improved chondrocytes density and matrix appearance. Furthermore, the permanence in situ of the hydrogel was longer than that of the linear Hyal.

Fibroin hydrogels for biomedical applications: preparation, characterization and in vitro cell culture studies

Silk fibroin hydrogels prepared either by treating a 2% (w/v) silk fibroin aqeuous solution at 4°C (thermgel) or by adding 30% (v/v) of glycerol (glygel), were characterized by using Environmental Scanning Electron Microscopy (ESEM), Fourier Transform Infrared Spectroscopy (FT-IR), Differential Scanning Calorimetry (DSC), Thermogravimetrical Analysis (TGA) and molecular weight determination. The preparation procedure affected morphology and molecular weight of hydrogels, with no or negligible differences being displayed by FT-IR and DSC analyses. While thermgel presented a well uniform porous structure, the morphology of glygel appeared to be non-porous and heterogeneous. Glygel presented lower water content and lower degradation temperatures, associated with the presence of glycerol but likely also to less-organized protein structures. Cytoxicity tests with human osteoblast-like cells indicated that both gels were not cytoxic, while cell cultures pointed out a faster cell proliferation on glygel and a higher cell activation and differentiation on thermgel. These gels could be used as scaffolds able to promote in situ bone regeneration.

Effect of Mg2+, Sr2+, and Mn2+ on the chemico-physical and in vitro biological properties of calcium phosphate biomimetic coatings

We previously developed a calcium phosphate (CaP) calcifying solution that allows to deposit a uniform layer of nanocrystalline apatite on metallic implants in a few hours. In this work we modified the composition of the CaP solution by addition of Sr(2+), Mg(2+), and Mn(2+), in order to improve the biological performance of the implants. The results of the investigation performed on the coatings, as well as on the powders precipitated in the absence of the substrates, indicate that both Sr(2+) and Mg(2+) reduce the extent of precipitation, although they are quantitatively incorporated into the nanocrystalline apatitic phase. The inhibitory effect on deposition is much more evident for Mn(2+), which completely hinders the precipitation of apatite and yields just a small amount of amorphous phosphate relatively rich in manganese content. Human osteoblast-like MG-63 cells cultured on the different materials show that the Mg(2+) and Sr(2+) apatitic coatings promote proliferation and expression of collagen type I, with respect to bare Ti and to the thin layer of amorphous phosphate obtained in the presence of Mn(2+). However, the relatively high content of Mn(2+) in the phosphate has a remarkable beneficial effect on osteocalcin production, which is even greater than that observed for Sr(2+).

Mechanical and histomorphometric evaluations of titanium implants with different surface treatments inserted in sheep cortical bone.

Improvement of the implant-bone interface is still an open problem and the interest in chemical modification of implant surfaces for cementless fixation has grown steadily over the past decade. Mechanical and histomorphometric investigations were performed at different times on implants inserted into sheep femoral cortical bone to compare the in vivo osseointegration of titanium screws ( X 3.5 x 7 mm length) with different surface treatments. After 8 weeks of implantation, the push-out force of anodized and hydrothermally treated implants (ANODIC) was significantly higher than that of machined implants (MACH) (36%, p<0.0005), whereas a decrease of 39% was observed for acid-etched implants (HF) when compared to other surface treatments. After 12 weeks of implantation, the push-out force values of HF implants were still significantly lower than those observed for MACH (-19%, p<0.01) and hydroxyapatite vacuum plasma-sprayed implants (HAVPS, -25%, p<0.0005), and the highest push-out force was found in HAVPS (p<0.001) implants. After 8 and 12 weeks of implantation, the AI of HF implants was significantly (p<0.05) lower ( approximately -25%) than that of MACH, HAVPS and ANODIC implants. In conclusion, results appear to confirm that there are no specific differences between ANODIC and HAVPS implants in terms of behavior. Moreover, although MACH implants show some surface contaminating agents, they appear to ensure good osseointegration within 12 weeks both mechanically and histomorphometrically, as do ANODIC and HAVPS implants. However, further studies are required to investigate bone hardness and mineralization around implants.

Laser Stimulation on Bone Defect Healing: An In Vitro Study

The aim of this in vitro study was to evaluate whether low-power laser (LPL) stimulation can accelerate bone healing. Bone defects of a standard area were created in the distal epiphysis of 12 femora explanted from six rats, and they were cultured in BGJb medium for 21 days. Six defects were treated daily with Ga-Al-As, 780 nm LPL for 10 consecutive days (lased group, LG), while the remainder were sham-treated (control group, CG). Alkaline phosphatase/total protein (ALP/TP), calcium (Ca), and nitric oxide (NO) were tested on days 7, 14 and 21 to monitor the metabolism of cultured bone. The percentage of healing of the defect area was determined by histomorphometric analysis. After 21 days significant increases were observed in ALP/TP in LG versus CG (p<0.001), in NO in the LG versus CG (p<0.0005) and in Ca in CG versus LG (p<0.001). The healing rate of the defect area in the LG was higher than in the CG (p=0.007). These in vitro results suggest that Ga-Al-As LPL treatment may play a positive role in bone defect healing.

A bone substitute composed of polymethylmethacrylate and α-tricalcium phosphate: results in terms of osteoblast function and bone tissue formation

The biological properties of a composite polymeric matrix (PMMA + alpha-TCP) made of polymethylmethacrylate (PMMA) and alfa-tricalciumphosphate (alpha-TCP) was tested by means of in vitro and in vivo investigations. PMMA was used as a comparative material. Osteoblast cultures (MG 63) demonstrated that PMMA + alpha-TCP significantly and positively affected osteoblast viability, synthetic activity and interleukin-6 level as compared to PMMA. At 12 weeks, the PMMA + alpha-TCP implants in rabbit bone successfully osteointegrated in trabecular and cortical tissue (affinity index: 57.14+/-8.84% and 68.31+/-6.18%, respectively). The newly formed bone after tetracycline labelling was histologically observed inside PMMA + alpha-TCP porosity. The microhardness test at the bone-PMMA + alpha-TCP interface showed a significantly higher rate of newly formed bone mineralization compared with PMMA (+83.5% and +58.5%, respectively), but differences still existed between newly formed and pre-existing normal bone. It is herein hypothesized that the present positive results may be ascribed to the porous macroarchitecture of PMMA + alpha-TCP and the presence of the bioactive ceramic material that could have a synergic effect and be responsible for the improvement of (a) the material colonization by bone cells, (b) osteoblast activity, (c) osteoinduction and osteoconduction processes, (d) bone remodelling.

Interaction of Sr-doped hydroxyapatite nanocrystals with osteoclast and osteoblast-like cells.

This article reports the effect of strontium incorporation into hydroxyapatite nanocrystals on bone cells response. Hydroxyapatite nanocrystals were synthesized at strontium contents of 0, 1, 3, 7 atom %. Strontium incorporation for calcium is confirmed by the linear increase of the unit cell parameters of hydroxyapatite, in agreement with the different ionic radii of the two ions. Moreover, strontium substitution slightly affects hydroxyapatite structural order and the shape of the nanocrystals. Osteoblast-like MG63 cells cultured on the nanocrystals display good proliferation and increased values of the differentiation parameters. In particular, when cultured on samples with Sr concentration in the range 3-7 atom %, osteoblasts display increased values of ALP activity, collagen type I, and osteocalcin production. Moreover, the osteoclast number on all the Sr-doped samples is significantly smaller than on hydroxyapatite, and it decreases on increasing strontium content. The data indicate that strontium stimulates osteoblast activity and exerts its inhibitory effect on osteoclast proliferation even when incorporated into hydroxyapatite.

A new austenitic stainless steel with negligible nickel content: an in vitro and in vivo comparative investigation

New nickel (Ni)-reduced stainless-steel metals have recently been developed to avoid sensitivity to Ni. In the present study, an austenitic Ni-reduced SSt named P558 (P558, Böhler, Milan, Italy) was studied in vitro on primary osteoblasts and in vivo after bone implantation in the sheep tibia, and was compared to ISO 5832-9 SSt (SSt) and Ti6Al4V. Cells were cultured directly on P558 and Ti6Al4V. Cells cultured on polystyrene were used as controls. Osteoblast proliferation, viability and synthetic activity were evaluated at 72 h by assaying WST1, alkaline phosphatase activity (ALP), nitric oxide, pro-collagen I (PICP), osteocalcin (OC), transforming growth factor-beta1 (TGFbeta-1) and interleukin-6 (IL-6) after 1.25(OH)2D3 stimulation. Under general anaesthesia, four sheep were submitted for bilateral tibial implantation of P558, SSt and Ti6Al4V rods. In vitro results demonstrated that the effect of P558 on osteoblast viability, PICP, TGF beta-1, tumor necrosis factor-alpha production did not significantly differ from that exerted by Ti6Al4V and controls. Furthermore, P558 enhanced osteoblast differentiation, as confirmed by ALP and OC levels, and reduced IL-6 production. At 26 weeks, the bone-to-implant contact was higher in P558 than in SSt (28%, p<0.005) and Ti6Al4V (4%, p<0.05), and was higher in Ti6Al4V than in SSt (22%, p<0.005). The tested materials did not affect bone microhardness in pre-existing host bone as evidenced by the measurements taken at 1000 microm from the bone-biomaterial interface (F=1.89, ns). At the bone-biomaterial interface the lowest HV value was found for SSt, whereas no differences in HV were observed between materials (F=1.55, ns). The current findings demonstrate P558 biocompatibility both in vitro and in vivo, and osteointegration processes are shown to be significantly improved by P558 as compared to the other materials tested.