Qiliang Chen

Electrospun carbon nanofibers as low-cost counter electrode for dye-sensitized solar cells.

Electrospun carbon nanofibers (ECNs) have been explored as an electrocatalyst and low-cost alternative to platinum (Pt) for triiodide reduction in dye-sensitized solar cells (DSCs). The results of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry measurements indicated that the ECN counter electrodes exhibited low charge-transfer resistance (Rct), large capacitance (C), and fast reaction rates for triiodide reduction. Although the efficiency (η) of ECN-based cells was slightly lower than that of Pt-based cells, their short circuit current density (Jsc) and open circuit voltage (Voc) were comparable. The ECN-based cells achieved an energy conversion efficiency (η) of 5.5 % under the AM 1.5 illumination at 100 mW cm(-2). The reason for lower cell performance using the ECN electrode was because of its lower fill factor (FF) than that of Pt-based cells, probably caused by high total series resistance (RStot) at ∼15.5 Ω cm2, which was larger than that of ∼4.8 Ω cm2 in the Pt-based devices. Simulated results showed that the fill factor (FF) and η could be substantially improved by decreasing RStot, which might be achieved by using thinner and highly porous ECNs to reduce the thickness of the ECNs counter electrode.

Benzothiadiazole-based polymer for single and double junction solar cells with high open circuit voltage.

Single and double junction solar cells with high open circuit voltage were fabricated using poly{thiophene-2,5-diyl-alt-[5,6-bis(dodecyloxy)benzo[c][1,2,5]thiadiazole]-4,7-diyl} (PBT-T1) blended with fullerene derivatives in different weight ratios. The role of fullerene loading on structural and morphological changes was investigated using atomic force microscopy (AFM) and X-ray diffraction (XRD). The XRD and AFM measurements showed that a higher fullerene mixing ratio led to breaking of inter-chain packing and hence resulted in smaller disordered polymer domains. When the PBT-T1:PC60BM weight ratio was 1 : 1, the polymer retained its structural order; however, large aggregated domains formed, leading to poor device performance due to low fill factor and short circuit current density. When the ratio was increased to 1 : 2 and then 1 : 3, smaller amorphous domains were observed, which improved photovoltaic performance. The 1 : 2 blending ratio was optimal due to adequate charge transport pathways giving rise to moderate short circuit current density and fill factor. Adding 1,8-diiodooctane (DIO) additive into the 1 : 2 blend films further improved both the short circuit current density and fill factor, leading to an increased efficiency to 4.5% with PC60BM and 5.65% with PC70BM. These single junction solar cells exhibited a high open circuit voltage at ∼ 0.9 V. Photo-charge extraction by linearly increasing voltage (Photo-CELIV) measurements showed the highest charge carrier mobility in the 1 : 2 film among the three ratios, which was further enhanced by introducing the DIO. The Photo-CELIV measurements with varying delay times showed significantly higher extracted charge carrier density for cells processed with DIO. Tandem devices using P3HT:IC60BA as bottom cell and PBT-T1:PC60BM as top cell exhibited a high open circuit voltage of 1.62 V with 5.2% power conversion efficiency.

Improved performance by morphology control via fullerenes in PBDT-TBT-alkoBT based organic solar cells

In this work, we report improved performance by controlling morphology using different fullerene derivatives in poly{2-octyldodecyloxy-benzo[1,2-b;3,4-b]dithiophene-alt-5,6-bis(dodecyloxy)-4,7-di(thieno[3,2-b]thiophen-2-yl)-benzo[c][1,2,5]thiadiazole} (PBDT-TBT-alkoBT) based organic solar cells. PC60BM and PC70BM fullerenes were used to investigate the characteristic changes in morphology and device performance. Fullerenes affect device efficiency by changing the active layer morphology. PC70BM with broader absorption than PC60BM resulted in reduced device performance which was elucidated by the intermixed granular morphology separating each larger grain in the PC70BM/polymer composite layer which created a higher density of traps. However after adding additive 1,8-diiodooctane (DIO), a fibrous morphology was observed due to the reduced solubility of the polymer and increased solubility of PC70BM in chloroform. The fibrous morphology improved charge transport leading to an increase in overall device performance. Atomic force microscopy (AFM), photo-induced charge extraction by linearly increasing voltage (photo-CELIV), and Kelvin probe force microscopy (KPFM) were used to investigate the nanoscale morphology of the active layer with different fullerene derivatives. For the PC60BM based active layer, AFM images revealed a dense fibrous morphology and more distinct fibrous morphology was observed by adding DIO. The PC70BM based active layer only exhibited an intermixed granular morphology instead of a fibrous morphology observed in the PC60BM based active layer. However, addition of DIO into the PC70BM based active layer led to fibrous morphology. When additive DIO was not used, a wider distribution of surface potential was observed for PC70BM than the PC60BM based active layer by KPFM measurements, indicating that polymer and fullerene domains are separated. When DIO was used, a narrower distribution of surface potential for both PC70BM and PC60BM based active layers was observed. Photo-CELIV experiments showed larger extracted charge carrier density and mobility in the PC70BM/DIO film.

Morphological Evolution and Its Impacts on Performance of Polymer Solar Cells

In this paper, the role of fullerene loading on the nanomorphology and photovoltaic performance of alternating copolymer poly{2-octyldodecyloxy-benzo[1,2-b;3,4-b] dithiophene-alt-5,6-bis(dodecyloxy)-4,7bis(thiophen-2-yl)-benzo[c] [1,2,5]-thiadiazole} (PBDT-ABT-1) blend films was investigated. The morphology of blend films with different Phenyl C-60-butyric acid methyl ester (PCBM) mixing ratios and solvent additives was studied using atomic force microscopy (AFM) and energy-filtered transmission electron microscopy (EFTEM). AFM and EFTEM images showed difference in the intermixing of polymer with fullerene between 1:1, 1:2, and 1:3 weight ratios. Polymer/PCBM intermixed domain size increases with higher PCBM weight ratios. X-ray diffraction measurements on the pristine polymer and blend films cast without additives did not show any peaks, suggesting an amorphous nature of PBDT-ABT-1. EFTEM images from the donor/acceptor composite showed intermixed polymer-PCBM domains separated by the polymer boundary. Furthermore, EFTEM images for di-iodooctane (DIO) additive cast film revealed purer polymer domain. Photo-charge extraction by linearly increasing voltage measurement exhibited that charge extraction is highest in the nanomorphology sample with a weight ratio of 1:2, corresponding to the lowest bimolecular recombination and the highest charge carrier mobility.