Qiting Huang

Physical and chemical properties of an antimicrobial Bis-GMA free dental resin with quaternary ammonium dimethacrylate monomer

The objective of this study was to evaluate the antibacterial activity, physicochemical properties of the quaternary ammonium dimethacrylate monomer N,N-bis[2-(3-(methacryloyloxy)propanamido)-ethyl]-N-methylhexadecyl ammonium bromide (IMQ-16) containing diurethane dimethacrylate (UDMA)/tricyclodecane dimethanol diacrylate (SR833s) resin system and compare with bisphenylglycidyl dimethacrylate (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) resin system. It was hypothesized that the physical and chemical properties of the experimental polymers would be comparable with Bis-GMA/TEGDMA polymer and IMQ-16 monomer could endow the UDMA/SR833s resin with antibacterial activity. Double bond conversion (DC) was measured using Fourier transform infrared spectroscopy (FTIR). Mechanical properties including flexural strength (FS) and flexural modulus (FM) were measured by three-point bending test with bars of 2mm×2mm×25mm. Water sorption (WS) and solubility (WSL) were also investigated. Antibacterial activity of obtained polymers against Streptococcus mutans Ingbitt (S. mutans) was tested through direct contact test (DCT). The presence of antibacterial activity due to soluble components was also investigated by agar diffusion test (ADT). All of the polymers containing IMQ-16 exhibited improvements in WS and WSL, while maintaining equivalent DC and FS relative to the Bis-GMA/TEGDMA control system. Incorporation of 17% and 20% of IMQ-16 into UDMA/SR833s resin reduced the viable counts of S. mutans after incubation on the surface of the materials and produced no inhibition zones around the cured discs in ADT. UDMA/SR833s resin system is promising to formulate an antibacterial polymer with equivalent or even higher physicochemical properties relative to Bis-GMA/TEGDMA formulation. IMQ-16 is capable to endow UDMA/SR833s resin system with significant antibacterial activity when the mass ratio is 17% or 20%.

Properties of discontinuous S2-glass fiber-particulate-reinforced resin composites with two different fiber length distributions

PURPOSE To investigate the reinforcing efficiency and light curing properties of discontinuous S2-glass fiber-particulate reinforced resin composite and to examine length distribution of discontinuous S2-glass fibers after a mixing process into resin composite. METHODS Experimental S2-glass fiber-particulate reinforced resin composites were prepared by mixing 10wt% of discontinuous S2-glass fibers, which had been manually cut into two different lengths (1.5 and 3.0mm), with various weight ratios of dimethacrylate based resin matrix and silaned BaAlSiO2 filler particulates. The resin composite made with 25wt% of UDMA/SR833s resin system and 75wt% of silaned BaAlSiO2 filler particulates was used as control composite which had similar composition as the commonly used resin composites. Flexural strength (FS), flexural modulus (FM) and work of fracture (WOF) were measured. Fractured specimens were observed by scanning electron microscopy. Double bond conversion (DC) and fiber length distribution were also studied. RESULTS Reinforcement of resin composites with discontinuous S2-glass fibers can significantly increase the FS, FM and WOF of resin composites over the control. The fibers from the mixed resin composites showed great variation in final fiber length. The mean aspect ratio of experimental composites containing 62.5wt% of particulate fillers and 10wt% of 1.5 or 3.0mm cutting S2-glass fibers was 70 and 132, respectively. No difference was found in DC between resin composites containing S2-glass fibers with two different cutting lengths. CONCLUSION Discontinuous S2-glass fibers can effectively reinforce the particulate-filled resin composite and thus may be potential to manufacture resin composites for high-stress bearing application.

Synthesis of antibacterial methacrylate monomer derived from thiazole and its application in dental resin

A non-quaternary ammonium antibacterial methacrylate monomer MEMT derived from thiazole was synthesized and applied into UDMA/TEGDMA dental resin with a series of mass fraction (10 wt%, 20 wt%, and 30 wt%). Double bond conversion, polymerization shrinkage, water sorption, solubility, flexural strength and modulus, and antibacterial activity of MEMT containing resin formulations were investigated with UDMA/TEGDMA as control resin. The results showed that MEMT containing dental resin had higher double bond conversion than control resin. Compared with control polymer, all MEMT containing polymer had comparable or lower polymerization shrinkage, water sorption and solubility, except for the polymer with 30 wt% of MEMT which had higher water sorption and solubility than control polymer. The MEMT had no influence on flexural strength and modulus before water immersion, but all MEMT containing polymers had lower flexural strength and modulus than control polymer after water immersion. The MEMT could endow dental polymer with obvious antibacterial activity by immobilizing MEMT into the polymeric network.

Genetic modification to induce CXCR2 overexpression in mesenchymal stem cells enhances treatment benefits in radiation-induced oral mucositis

Radiation-induced oral mucositis affects patient quality of life and reduces tolerance to cancer therapy. Unfortunately, traditional treatments are insufficient for the treatment of mucositis and might elicit severe side effects. Due to their immunomodulatory and anti-inflammatory properties, the transplantation of mesenchymal stem cells (MSCs) is a potential therapeutic strategy for mucositis. However, systemically infused MSCs rarely reach inflamed sites, impacting their clinical efficacy. Previous studies have demonstrated that chemokine axes play an important role in MSC targeting. By systematically evaluating the expression patterns of chemokines in radiation/chemical-induced oral mucositis, we found that CXCL2 was highly expressed, whereas cultured MSCs negligibly express the CXCL2 receptor CXCR2. Thus, we explored the potential therapeutic benefits of the transplantation of CXCR2-overexpressing MSCs (MSCsCXCR2) for mucositis treatment. Indeed, MSCsCXCR2 exhibited enhanced targeting ability to the inflamed mucosa in radiation/chemical-induced oral mucositis mouse models. Furthermore, we found that MSCCXCR2 transplantation accelerated ulcer healing by suppressing the production of pro-inflammatory chemokines and radiogenic reactive oxygen species (ROS). Altogether, these findings indicate that CXCR2 overexpression in MSCs accelerates ulcer healing, providing new insights into cell-based therapy for radiation/chemical-induced oral mucositis.

Alcohol Inhibits Odontogenic Differentiation of Human Dental Pulp Cells by Activating mTOR Signaling

Long-term heavy alcohol consumption could result in a range of health, social, and behavioral problems. People who abuse alcohol are at high risks of seriously having osteopenia, periodontal disease, and compromised oral health. However, the role of ethanol (EtOH) in the biological functions of human dental pulp cells (DPCs) is unknown. Whether EtOH affects the odontoblastic differentiation of DPCs through the mechanistic target of rapamycin (mTOR) remains unexplored. The objective of this study was to investigate the effects of EtOH on DPC differentiation and mineralization. DPCs were isolated and purified from human dental pulps. The proliferation and odontoblastic differentiation of DPCs treated with EtOH were subsequently investigated. Different doses of EtOH were shown to be cytocompatible with DPCs. EtOH significantly activated the mTOR pathway in a dose-dependent manner. In addition, EtOH downregulated the alkaline phosphatase activity, attenuated the mineralized nodule formation, and suppressed the expression of odontoblastic markers including ALP, DSPP, DMP-1, Runx2, and OCN. Moreover, the pretreatment with rapamycin, a specific mTOR inhibitor, markedly reversed the EtOH-induced odontoblastic differentiation and cell mineralization. Our findings show for the first time that EtOH can suppress DPC differentiation and mineralization in a mTOR-dependent manner, indicating that EtOH may be involved in negatively regulating the dental pulp repair.

Physicochemical properties of discontinuous S2-glass fiber reinforced resin composite

The objective of this study was to investigate several physicochemical properties of an experimental discontinuous S2-glass fiber-reinforced resin composite. The experimental composite was prepared by mixing 10 wt% of discontinuous S2-glass fibers with 27.5 wt% of resin matrix and 62.5 wt% of particulate fillers. Flexural strength (FS) and modulus (FM), fracture toughness (FT), work of fracture (WOF), double bond conversion (DC), Vickers hardness, volume shrinkage (VS) and fiber length distribution were determined. These were compared with two commercial resin composites. The experimental composite showed the highest FS, WOF and FT compared with two control composites. The DC of the experimental composite was comparable with controls. No significant difference was observed in VS between the three tested composites. The use of discontinuous glass fiber fillers with polymer matrix and particulate fillers yielded improved physical properties and substantial improvement was associated with the use of S2-glass fiber.

The antibacterial, cytotoxic, and flexural properties of a composite resin containing a quaternary ammonium monomer

Statement of problem. The use of composite resin to restore teeth has increased substantially during the last decades. However, secondary caries and the fracture of restorations are the leading reasons for clinical restoration failure. Mechanically strong composite resins with caries‐inhibition capabilities are needed. Although antibacterial dimethacrylate quaternary ammonium monomers have been synthesized, composite resin containing dimethacrylate quaternary ammonium monomers and glass fillers has rarely been reported. Purpose. The purpose of this in vitro study was to evaluate the possibility of the clinical use of an experimental composite resin containing urethane dimethacrylate quaternary ammonium compound (UDMQA‐12) by investigating its antibacterial activity, cytotoxicity, flexural strength, and flexural modulus. Material and methods. Antibacterial activity against Streptococcus mutans was investigated by means of direct contact test. The antibacterial activity of specimens after water immersion and saliva treatment was also tested. These were compared with a commercially available composite resin, Z250, and a glass ionomer cement, Fuji VII. Effects of the eluent from the experimental composite resin on the metabolic activity of human dental pulp cells were quantified. Disks of 1 mm in thickness and 15 mm in diameter were used in the antibacterial and cytotoxic tests. Flexural strength and flexural modulus were measured with a 3‐point bend test with bars of 2×2×25 mm. Three commercially available composite resins (Filtek Z250, G‐aenial Anterior, and G‐aenial Posterior) were used as controls in the flexural test. Results. Bacterial growth was inhibited on the experimental composite resin. After water immersion or saliva treatment, the experimental composite resin showed significant antibacterial effect compared with the conventional composite resin (P<.05). No significant difference was found in cytotoxicity between the experimental composite resin and the conventional composite resin (P > .05), and a significantly higher cytotoxicity was shown by glass ionomer cement compared with the experimental composite resin and the conventional composite resin (P<.05). The conventional composite resin had the highest flexural strength and flexural modulus (P<.05), followed by the experimental composite resin, then G‐ænial Posterior and G‐ænial Anterior. Conclusions. The antibacterial experimental composite resin was biocompatible and had mechanical properties similar to those of some commercially available composite resins. It might, therefore, be useful in preventing the occurrence of secondary caries.

Mechanical and antibacterial properties of benzothiazole-based dental resin materials

Abstract A synthesized benzothiazole containing mono-methacrylate monomer BTTMA was incorporated into Bis-GMA/TEGDMA dental resin system with a series of mass concentration from 5 to 30 wt.% as an antibacterial agent. The influence of BTTMA on physicochemical properties of dental resin system, such as double bond conversion (DC), volumetric shrinkage (VS), flexural strength (FS) and modulus (FM), water sorption (WS) and solubility (SL) were investigated. Direct contact testing and agar diffusion testing were used to evaluate the antibacterial activity of BTTMA containing dental resin. The results showed that BTTMA could endow dental resin with significant antibacterial activity when its concentration reached a certain amount (20 wt.%), and the antibacterial activity of BTTMA containing dental resin was mainly attributed to the immobilized BTTMA instead of the unreacted leachable BTTMA. BTTMA had no negative effect on physicochemical properties of dental resin, and even some BTTMA containing dental resins had advantages like higher DC, lower VS and WS when compared with control resin. Therefore, BTTMA could be considered as a suitable antibacterial agent in dental material, but much more researches concerned about biocompatibility should be done in future to prove whether it could be applied in clinic.

AIM2 Inflammasome Is Critical for dsDNA-Induced IL-1β Secretion in Human Dental Pulp Cells

The AIM2 inflammasome pathway has been determined to play an important role in cellular immune defense against bacterial and viral infections; however, its function and regulatory mechanism in human dental pulp cells (HDPCs) during pulpitis remains poorly understood. In this study, we explored whether the AIM2 inflammasome pathway was activated in HDPCs in response to dsDNA and defined its role in regulating IL-1β secretion. We demonstrated that stimulation with IFN-γ and cytoplasmic DNA significantly activated the AIM2 inflammasome and increased IL-1β secretion in HDPCs. Moreover, AIM2 overexpression significantly up-regulated both cleaved Caspase-1 expression and IL-1β release in HDPCs, while suppression of ASC and Caspase-1 resulted in down-regulation of cleaved Caspase-1 and IL-1β secretion. These results suggest that Caspase-1-dependent IL-1β processing and secretion require the AIM2 inflammasome pathway in HDPCs and that the AIM2 inflammasome pathway is critical for regulation of the dental pulp immune response.