Renzo A. Raso

Template-Particle Stabilized Bicontinuous Emulsion Yielding Controlled Assembly of Hierarchical High-Flux Filtration Membranes

A novel solvent-evaporation-based process that exploits template-particle stabilized bicontinuous emulsions for the formation of previously unreached membrane morphologies is reported in this article. Porous membranes have a wide range of applications spanning from water filtration, pharmaceutical purification, and battery separators to scaffolds for tissue engineering. Different situations require different membrane morphologies including various pore sizes and pore gradients. However, most of the previously reported membrane preparation procedures are restricted to specific morphologies and morphology alterations require an extensive optimization process. The tertiary system presented in this article, which consists of a poly(ether sulfone)/dimethylacetamide (PES/DMAc) solution, glycerol, and ZnO-nanoparticles, allows simple and exact tuning of pore diameters ranging from sub-20 nm, up to 100 nm. At the same time, the pore size gradient is controlled from 0 up to 840%/μm yielding extreme asymmetry. In addition to structural analysis, water flux rates of over 5600 L m(-2) h(-1) are measured for membranes retaining 45 nm silica beads.

Magnetic superbasic proton sponges are readily removed and permit direct product isolation.

Workup in organic synthesis can be very time-consuming, particularly when using reagents with both a solubility similar to that of the desired products and a tendency not to crystallize. In this respect, reactions involving organic bases would strongly benefit from a tremendously simplified separation process. Therefore, we synthesized a derivative of the superbasic proton sponge 1,8-bis(dimethylamino)naphthalene (DMAN) and covalently linked it to the strongest currently available nanomagnets based on carbon-coated cobalt metal nanoparticles. The immobilized magnetic superbase reagent was tested in Knoevenagel- and Claisen-Schmidt-type condensations and showed conversions of up to 99%. High yields of up to 97% isolated product could be obtained by simple recrystallization without using column chromatography. Recycling the catalyst was simple and fast with an insignificant decrease in catalytic activity.

Limestone nanoparticles as nanopore templates in polymer membranes: narrow pore size distribution and use as self-wetting dialysis membranes

Limestone nanoparticles can be used as nanopore templates to prepare porous polymeric films. Their application as membranes is so far strongly limited by the fact that these films are highly hydrophobic. In this study, a simple method is reported to directly produce self-wetting membranes by the template removal method. Triethyl citrate modified polyethersulfone and cellulose acetate membranes were produced using dissolvable limestone nanoparticles as pore templates. The nanoporous polymer films were used as dialysis membranes and characterized by means of buffer exchange rate, molecular weight cut-off, protein adsorption, pore size distribution and water contact angle. The herein prepared membranes were further benchmarked against commercially available dialysis membranes with comparable average pore size. They showed narrow pore size distributions, fast dialysis rates at low protein adsorption and molecular weight cut-off of around 12 kDa. Interestingly, the triethyl citrate modified polyethersulfone membranes displayed only moderate change in pore size distribution as a result of the plasticizer additive compared to pure polyethersulfone membranes. This is a matter of substantial interest considering the fact that additive modifications of membranes produced by the predominant phase inversion process typically show alterations in morphology that lead to undesired changes in membrane performance. Furthermore, dextran recovery analysis proved to meet the specific requirements for dialysis membrane characterization and benchmarking.

Physical mixtures of CeO2 and zeolites as regenerable indoor air purifiers: adsorption and temperature dependent oxidation of VOC

Removal of volatile organic compounds (VOC) and indoor air quality regulation through adsorbers required exchange or maintenance of active materials. In this work, we combine well known VOC adsorbers with oxidation catalysts as intimate particulate mixtures. We demonstrate how typical VOC can subsequently adsorb on such mixed material fixed beds (usually days to weeks; the common state of the system, adsorption phase) using small organic compounds (diethyl ether, triethylamine), monoterpenes such as linalool and limonene, and hexanoic acid. Occasional regeneration runs through heat up of the fixed bed results in simultaneous desorption and oxidation of the accumulated VOC, thus regenerating full adsorption capacity for a next adsorption phase. We investigated both small pore zeolites (H-ZSM-5) and larger pore zeolites (13X) and found a distinct interplay between the pore size and the type of VOC. Thermogravimetry coupled with mass spectroscopy was used to quantitatively study the effects of mixing composition and temperature on adsorber performance and regeneration. The here investigated bi-functional systems combine very low maintenance costs and materials requirement with low air flow and exchange costs, thus suggesting mixed (two-functional) bed adsorbers with catalytic function as sustainable alternatives to currently used single use systems based on granulated zeolites or activated carbon. In this work we show the ability of zeolite/cerium oxide physical mixtures to adsorb and capture different classes of VOC at room temperature and release them for oxidation at higher temperatures in a regenerative and sustainable process.

Ferromagnetic inks facilitate large scale paper recycling and reduce bleach chemical consumption.

Deinking is a fundamental part of paper recycling. As the global paper consumption rises and exceeds even the annual paper production, recycling of this raw material is of high importance. Magnetic ink based on carbon coated magnetic nanoparticles enables an alternative approach to state of the art paper deinking. Magnetic deinking comprises three steps (preselection, washing, and magnetic separation of fibers). Preseparation of printed from nonprinted scraps of paper is feasible and reduces the paper mass which has to be fed into a deinking process. A consecutive washing process removes surficial magnetic ink that can be collected by application of a permanent magnet. Still, printed parts are subjected to a further continuous magnetic deinking step, where magnetic and nonmagnetic paper fibers can be separated. Magnetic deinking of a model print allows recovery of more than 80% of bright fibers without any harsh chemical treatment and the re-collection of more than 82% of magnetic ink.

β‐D‐Glucosidase Assisted Gold Dissolution as Non‐Optical and Quantifiable Detection Technique for Immunoassays

Immunoassays are used for detecting protein targets for various applications. Here, a modification of immunoassays to allow a purely electrical detection of the target protein concentration is shown. The modification comprises a β-D-glucosidase as reporter enzyme and a cyanogenic glycoside as substrate. The enzymatic reaction produces cyanide in small quantities. For electrical detection of the cyanide, a novel sensor is developed, based on a gold micro wire. The cyanide dissolves the gold wire and changes the electrical resistance of the wire. Monitoring the resistance change allows a quantitative measurement of the target human C-reactive protein (an inflammatory marker) in blood plasma in the physiological relevant concentration range.

Physical mixtures of CeO2 and zeolites as regenerable indoor air purifiers

Removal of volatile organic compounds (VOC) and indoor air quality regulation through adsorbers required exchange or maintenance of active materials. In this work, we combine well known VOC adsorbers with oxidation catalysts as intimate particulate mixtures. We demonstrate how typical VOC can subsequently adsorb on such mixed material fixed beds (usually days to weeks; the common state of the system, adsorption phase) using small organic compounds (diethyl ether, triethylamine), monoterpenes such as linalool and limonene, and hexanoic acid. Occasional regeneration runs through heat up of the fixed bed results in simultaneous desorption and oxidation of the accumulated VOC, thus regenerating full adsorption capacity for a next adsorption phase. We investigated both small pore zeolites (H-ZSM-5) and larger pore zeolites (13X) and found a distinct interplay between the pore size and the type of VOC. Thermogravimetry coupled with mass spectroscopy was used to quantitatively study the effects of mixing composition and temperature on adsorber performance and regeneration. The here investigated bi-functional systems combine very low maintenance costs and materials requirement with low air flow and exchange costs, thus suggesting mixed (two-functional) bed adsorbers with catalytic function as sustainable alternatives to currently used single use systems based on granulated zeolites or activated carbon. In this work we show the ability of zeolite/cerium oxide physical mixtures to adsorb and capture different classes of VOC at room temperature and release them for oxidation at higher temperatures in a regenerative and sustainable process.