Roald M. Tiggelaar

Heat and mass transfer in a square microchannel with asymmetric heating

This paper describes the heat and mass transfer in a square microchannel that is heated from one side. This microchannel represents a reaction channel in a microreactor that is used to study the kinetics of the catalytic partial oxidation of methane. The microchannel is contained in a silicon wafer and is covered by a thin silicon sheet. At the top side of this sheet, heating elements are present which mimic the heat that is produced as a result of the exothermic chemical reaction. Correlations for Nusselt and Sherwood numbers as a function of the Graetz number are derived for laminar and plug flow conditions. These correlations describe the heat and mass transport at the covering top sheet of the microchannel as well as at its side and bottom walls. By means of computational fluid dynamic simulations, the laminar flow is studied. To determine an approximate laminar flow Nusselt correlation, the heat transport was solved analytically for plug flow conditions to describe the influence of changes in the thermal boundaries of the system. The laminar flow case is experimentally validated by measuring the actual temperature distribution in a 500 μm square, 3 cm long, microchannel that is covered by a 1 μm and by a 1.9 μm thick silicon sheet with heating elements and temperature sensors on top. The Nusselt and Sherwood correlations can be used to readily quantify the heat and mass transport to support kinetic studies of catalytic reactions in this type of microreactor.

A Brush‐Gel/Metal‐Nanoparticle Hybrid Film as an Efficient Supported Catalyst in Glass Microreactors

A polymer-brush-based material was applied for the formation and in situ immobilization of silver and palladium nanoparticles, as a catalytic coating on the inner wall of glass microreactors. The brush film was grown directly on the microchannel interior by means of atom-transfer radical polymerization (ATRP), which allows control over the polymer film thickness and therefore permits the tuning of the number of nanoparticles formed on the channel walls. The wide applicability of the catalytic devices is demonstrated for the reduction of 4-nitrophenol and for the Heck reaction.

Substantial rate enhancements of the esterification reaction of phthalic anhydride with methanol at high pressure and using supercritical CO2 as a co-solvent in a glass microreactor

The esterification reaction of phthalic anhydride with methanol was performed at different temperatures in a continuous flow glass microreactor at pressures up to 110 bar and using supercritical CO(2) as a co-solvent. The design is such that supercritical CO(2) can be generated inside the microreactor. Substantial rate enhancements were obtained, viz. a 53-fold increase was obtained at 110 bar and 60 degrees C. Supercritical CO(2) as a co-solvent gave rise to a 5400-fold increase (both with respect to batch experiments at 1 bar at the same temperature).

A light detection cell to be used in a micro analysis system for ammonia

This paper describes the design, realization and characterization of a micromachined light detection cell. This light detection cell is designed to meet the specifications needed for a micro total analysis system in which ammonia is converted to indophenol blue. The concentration of indophenol blue is measured in a light detection cell. The light detection cell was created using KOH/IPA etching of silicon. The KOH/IPA etchant was a 31 wt.% potassium hydroxide (KOH) solution with 250 ml isopropyl alcohol (IPA) per 1000 ml H(2)O added to it. The temperature of the solution was 50 degrees C. Etching with KOH/IPA results in 45 degrees sidewalls ({110} planes) which can be used for the in- and outcoupling of the light. The internal volume of the realized light detection cell is smaller than 1 mul, enabling measurements on samples in the order of only 1 mul. Measurements were performed on indophenol blue samples in the range of 0.02 to 50 muM. In this range the measurements showed good reproducibility.

Column coupling isotachophoresis-capillary electrophoresis with mass spectrometric detection: Characterization and optimization of microfluidic interfaces

Two-dimensional electrophoretic separations are one of the most promising tools for the continuously growing needs of different bioanalytical fields such as proteomics and metabolomics. In this work we present the design and the implementation of a two-dimensional electrophoretic separation coupled to mass spectrometry. We started our work studying the sample transfer characteristics of different microfluidic interfaces compatible with capillary coupling for two-dimensional electrophoretic separations. These junctions are aimed at method decoupling and sample transfer in a modular two-dimensional electrophoretic separation system. In order to perform the characterization of the interfaces, we carried out capillary electrophoresis experiments and numerical simulations using three cationic compounds under different flow conditions. The comparison of the experimental and simulation results enables us to clearly define the desirable characteristics of interfaces in order to achieve method orthogonality with lossless sample transfer in a two-dimensional separation system. Finally, we present a glass microfluidic chip as interface for the implementation of a novel hybrid modular system for performing two-dimensional electrophoretic separations involving isotachophoresis and capillary electrophoresis. In this setup we include mass spectrometric and contactless capacitively coupled conductivity detection to monitor the separation process. We demonstrate the ability of the setup to be used as a flexible analysis tool by performing preconcentration, separation, detection and identification of four different human angiotensin peptides.

Fabrication and doping methods for silicon nano- and micropillar arrays for solar cell applications: a review

Silicon is one of the main components of commercial solar cells and is used in many other solar-light-harvesting devices. The overall efficiency of these devices can be increased by the use of structured surfaces that contain nanometer- to micrometer-sized pillars with radial p/n junctions. High densities of such structures greatly enhance the light-absorbing properties of the device, whereas the 3D p/n junction geometry shortens the diffusion length of minority carriers and diminishes recombination. Due to the vast silicon nano- and microfabrication toolbox that exists nowadays, many versatile methods for the preparation of such highly structured samples are available. Furthermore, the formation of p/n junctions on structured surfaces is possible by a variety of doping techniques, in large part transferred from microelectronic circuit technology. The right choice of doping method, to achieve good control of junction depth and doping level, can contribute to an improvement of the overall efficiency that can be obtained in devices for energy applications. A review of the state-of-the-art of the fabrication and doping of silicon micro and nanopillars is presented here, as well as of the analysis of the properties and geometry of thus-formed 3D-structured p/n junctions.

Microfluidic Devices for Forensic DNA Analysis: A Review

Microfluidic devices may offer various advantages for forensic DNA analysis, such as reduced risk of contamination, shorter analysis time and direct application at the crime scene. Microfluidic chip technology has already proven to be functional and effective within medical applications, such as for point-of-care use. In the forensic field, one may expect microfluidic technology to become particularly relevant for the analysis of biological traces containing human DNA. This would require a number of consecutive steps, including sample work up, DNA amplification and detection, as well as secure storage of the sample. This article provides an extensive overview of microfluidic devices for cell lysis, DNA extraction and purification, DNA amplification and detection and analysis techniques for DNA. Topics to be discussed are polymerase chain reaction (PCR) on-chip, digital PCR (dPCR), isothermal amplification on-chip, chip materials, integrated devices and commercially available techniques. A critical overview of the opportunities and challenges of the use of chips is discussed, and developments made in forensic DNA analysis over the past 10–20 years with microfluidic systems are described. Areas in which further research is needed are indicated in a future outlook.

Room-temperature intermediate layer bonding for microfluidic devices

In this work a novel room-temperature bonding technique based on chemically activated Fluorinated Ethylene Propylene (FEP) sheet as an intermediate between chemically activated substrates is presented. Surfaces of silicon and glass substrates are chemically modified with APTES bearing amine terminal groups, while FEP sheet surfaces are treated to form carboxyl groups and subsequently activated by means of EDC-NHS chemistry. The activation procedures of silicon, glass and FEP sheet are characterized by contact angle measurements and XPS. Robust bonds are created at room-temperature by simply pressing two amine-terminated substrates together with activated FEP sheet in between. Average tensile strengths of 5.9 MPa and 5.2 MPa are achieved for silicon-silicon and glass-glass bonds, respectively, and the average fluidic pressure that can be operated is 10.2 bar. Moreover, it is demonstrated that FEP-bonded microfluidic chips can handle mild organic solvents at elevated pressures without leakage problems. This versatile room-temperature intermediate layer bonding technique has a high potential for bonding, packaging, and assembly of various (bio-) chemical microfluidic systems and MEMS devices.

Electrical properties of low pressure chemical vapor deposited silicon nitride thin films for temperatures up to 650 °C

The results of a study on electrical conduction in low pressure chemical vapor deposited silicon nitride thin films for temperatures up to 650 °C are described. Current density versus electrical field characteristics are measured as a function of temperature for 100 and 200 nm thick stoichiometric (Si3N4) and low stress silicon-rich (SiRN) films. For high E-fields and temperatures up to 500 °C conduction through Si3N4 can be described well by Frenkel–Poole transport with a barrier height of ∼ 1.10 eV, whereas for SiRN films Frenkel–Poole conduction prevails up to 350 °C with a barrier height of ∼ 0.92 eV. For higher temperatures, dielectric breakdown of the Si3N4 and SiRN films occurred before the E-field was reached above which Frenkel–Poole conduction dominates. A design graph is given that describes the maximum E-field that can be applied over silicon nitride films at high temperatures before electrical breakdown occurs.

Glucose level determination with a multi-enzymatic cascade reaction in a functionalized glass chip

In this work we show the functionalization of the interior of microfluidic glass chips with poly(2-hydroxyethyl methacrylate) polymer brushes as anchors for co-immobilization of the enzymes glucose-oxidase and horseradish peroxidase. The formation of the brush layer and subsequent immobilization of these enzymes have been characterized on flat surfaces by atomic force microscopy and Fourier transform infrared spectroscopy, and studied inside glass chips by field emission scanning microscopy. Enzyme-functionalized glass chips have been applied for performing a multi-enzymatic cascade reaction for the fast (20 s) determination of glucose in human blood samples and the result is in excellent agreement with values obtained from the conventional hospital laboratory. The limit of detection of this bi-enzymatic method is 60 μM. With the advantages of high selectivity and reproducibility, this functionalization method can be used for improving the efficiency of glucose sensors.