Rob Adamson

A split-aperture transmit beamforming technique with phase coherence grating lobe suppression

A small element-to-element pitch (~.5λ) is conventionally required for phased array ultrasound transducers to avoid large grating lobes. This constraint can introduce many fabrication difficulties, particularly in the development of high-frequency phased arrays at operating frequencies greater than 30 MHz. In this paper, a new transmit beamforming technique along with sign coherence factor (SCF) receive beamforming is proposed to suppress grating lobes in large-pitch phased-array transducers. It is based on splitting the transmit aperture (N elements) into N/K transmit elements and receive beamforming on all N elements to reduce the temporal length of the transmit grating lobe signal. Therefore, the use of synthetic aperture beamforming, which can introduce relative phase distortions between the echoes received over many transmit events, can be avoided. After each transmit-receive event, the received signals are weighted by the calculated SCF to suppress the grating lobes. After pulsing all sub-apertures, the RF signals are added to generate one line of the image. Simulated 2-way radiation patterns for different K values show that grating lobes can be suppressed significantly at different steering angles. Grating lobes can be suppressed by approximately 20 dB with K = 2 at steering angles greater than 25° and an element pitch greater than 0.75λ. A technique for determining the optimal transmit sub-apertures has been developed.

High-Frequency Ex vivo Ultrasound Imaging of the Auditory System

A 50MHz array-based imaging system was used to obtain high-resolution images of the ear and auditory system. This previously described custom built imaging system (Brown et al. 2004a, 2004b; Brown and Lockwood 2005) is capable of 50 microm axial resolution, and lateral resolution varying from 80 microm to 130 microm over a 5.12 mm scan depth. The imaging system is based on a 2mm diameter, seven-element equal-area annular array, and a digital beamformer that uses high-speed field programmable gate arrays (FPGAs). The images produced by this system have shown far superior depth of field compared with commercially available single-element systems. Ex vivo, three-dimensional (3-D) images were obtained of human cadaveric tissues including the ossicles (stapes, incus, malleus) and the tympanic membrane. In addition, two-dimensional (2-D) images were obtained of an intact cochlea by imaging through the round window membrane. The basilar membrane inside the cochlea could clearly be visualized. These images demonstrate that high-frequency ultrasound imaging of the middle and inner ear can provide valuable diagnostic information using minimally invasive techniques that could potentially be implemented in vivo.

Direct measurement of the wavelength of sound waves in the human skull

The results of a study of the three-dimensional vibration of two dry human skulls in response to harmonic excitation are presented. The vibratory response exhibits three distinct types of motion across the range of audible frequencies. At low frequencies below 1000 Hz, whole-head quasi-rigid motion is seen. At the middle frequencies between 1000 and 6000 Hz, the motion exhibits a series of increasingly complex modal patterns. Above 6000 Hz, the response is wavelike and clear wavefronts can be distinguished in the vibration data. In this regime the relationship between wavelength and frequency is calculated and compared to a number of theories of skull vibration that have been proposed.

Long-range, wide-field swept-source optical coherence tomography with GPU accelerated digital lock-in Doppler vibrography for real-time, in vivo middle ear diagnostics.

We present the design, implementation and validation of a swept-source optical coherence tomography (OCT) system for real-time imaging of the human middle ear in live patients. Our system consists of a highly phase-stable Vernier-tuned distributed Bragg-reflector laser along with a real-time processing engine implemented on a graphics processing unit. We use the system to demonstrate, for the first time in live subjects, real-time Doppler measurements of middle ear vibration in response to sound, video rate 2D B-mode imaging of the middle ear and 3D volumetric B-mode imaging. All measurements were performed non-invasively through the intact tympanic membrane demonstrating that the technology is readily translatable to the clinic.

Mass-spring matching layers for high-frequency ultrasound transducers: a new technique using vacuum deposition

We have developed a technique of applying multiple matching layers to high-frequency (>30 MHz) imaging transducers, by using carefully controlled vacuum deposition alone. This technique uses a thin mass-spring matching layer approach that was previously described in a low-frequency (1 to 10 MHz) transducer design with epoxied layers. This mass- spring approach is more suitable to vacuum deposition in highfrequency transducers over the conventional quarter-wavelength resonant cavity approach, because thinner layers and more versatile material selection can be used, the difficulty in precisely lapping quarter-wavelength matching layers is avoided, the layers are less attenuating, and the layers can be applied to a curved surface. Two different 3-mm-diameter 45-MHz planar lithium niobate transducers and one geometrically curved 3-mm lithium niobate transducer were designed and fabricated using this matching layer approach with copper as the mass layer and parylene as the spring layer. The first planar lithium niobate transducer used a single mass-spring matching network, and the second planar lithium niobate transducer used a single mass-spring network to approximate the first layer in a dual quarter-wavelength matching layer system in addition to a conventional quarter-wavelength layer as the second matching layer. The curved lithium niobate transducer was press focused and used a similar mass-spring plus quarter-wavelength matching layer network. These transducers were then compared with identical transducers with no matching layers and the performance improvement was quantified. The bandwidth of the lithium niobate transducer with the single mass-spring layer was measured to be 46% and the insertion loss was measured to be -21.9 dB. The bandwidth and insertion loss of the lithium niobate transducer with the mass-spring network plus quarter-wavelength matching were measured to be 59% and -18.2 dB, respectively. These values were compared with the unmatched transducer, which had a bandwidth of 28% and insertion loss of -34.1 dB. The bandwidth and insertion loss of the curved lithium niobate transducer with the mass-spring plus quarter-wavelength matching layer combination were measured to be 68% and -26 dB, respectively; this compared with the measured unmatched bandwidth and insertion loss of 35% and -37 dB. All experimentally measured values were in excellent agreement with theoretical Krimholtz-Leedom-Matthaei (KLM) model predictions.

Optical coherence tomography system requirements for clinical diagnostic middle ear imaging

Abstract. Noninvasive middle ear imaging using optical coherence tomography (OCT) presents some unique challenges for real-time, clinical use in humans. We present results from a two-dimensional/three-dimensional OCT system built to assess the imaging requirements of clinical middle ear imaging, and the technical challenges associated with them. These include the need to work at a low numerical aperture, the deleterious effects of transtympanic imaging on image quality at the ossicles, sensitivity requirements for clinical fidelity of images at real-time rates, and the high dynamic-range requirements of the ear. We validated the system by imaging cadaveric specimens with simulated disorders to show the clinical applicability of the images. We also provide additional insight into the likely role of OCT in clinical otology.

Compensating for Tissue Changes in an Ultrasonic Power Link for Implanted Medical Devices

Ultrasonic power transfer using piezoelectric devices is a promising wireless power transfer technology for biomedical implants. However, for sub-dermal implants where the separation between the transmitter and receiver is on the order of several acoustic wavelengths, the ultrasonic power transfer efficiency (PTE) is highly sensitive to the distance between the transmitter and receiver. This sensitivity can cause large swings in efficiency and presents a serious limitation on battery life and overall performance. A practical ultrasonic transcutaneous energy transfer (UTET) system design must accommodate different implant depths and unpredictable acoustic changes caused by tissue growth, hydration, ambient temperature, and movement. This paper describes a method used to compensate for acoustic separation distance by varying the transmit (Tx) frequency in a UTET system. In a benchtop UTET system we experimentally show that without compensation, power transfer efficiency can range from 9% to 25% as a 5 mm porcine tissue sample is manipulated to simulate in situ implant conditions. Using an active frequency compensation method, we show that the power transfer efficiency can be kept uniformly high, ranging from 20% to 27%. The frequency compensation strategy we propose is low-power, non-invasive, and uses only transmit-side measurements, making it suitable for active implanted medical device applications.

The design of ultrasonic lead magnesium niobate-lead titanate (PMN-PT) composite transducers for power and signal delivery to implanted hearing aids

We present a system for efficiently powering implanted hearing aids by transmitting an ultrasonic signal across the skin. The use of ultrasound as method for power and signal transfer is known for embedded systems in industrial applications and has more recently been investigated for use with other medical implants. In our application, ultrasonic transducers are investigated as they offer substantially reduced size relative to traditional magnetic induction coil power delivery. The developed transducers use lead magnesium niobate-lead titanate (PMN-PT) piezoelectric material in a 1–3 composite formulation. PMN-PT offers an electromechanical coupling factor (kt, an indicator of maximum efficiency) that is up to 60% greater than traditional piezoceramics, while the use of composite transducers removes geometric constraints that can limit the achieved efficiency. The fabrication methods for the transducers are detailed. Experimental results are presented to show the composite transducers achieve a kt of 0.86 (out of 1.00), and a power transmission efficiency that is improved by 38% relative to a similar non-composite transducers. It is also demonstrated that these transducers offer sufficient bandwidth for amplitude or frequency modulation schemes to transmit data signals along the power carrier beam.

Fabrication of a miniaturized 64-element high-frequency phased array

We have developed a 40 MHz, 64-element phased array transducer packaged into a 2.5mm by 3.1mm endoscopic form factor. The array is a forward looking kerfless design based on PMN-32%PT with an element-to-element pitch of 38 microns. In order to achieve such a miniaturized form factor, a novel technique of wire bonding the array elements to a miniature flex circuit oriented in line with the forward looking ultrasound beam was developed. A technique of scratch dicing the back of the array was also implemented in order to improve directivity of the array elements The array was fabricated with a single P(DVF-TrFE) matching layer and a TPX lens for passive elevation focussing to a depth of 7mm. The two-way -6dB pulse bandwidth was measured to be 55% and the average electromechanical coupling (kT) for the individual elements was measured to be 0.62. The one-way directivity pattern from single elements was measured to be +/25 degrees, which was shown to be a large improvement compared to an identical kerfless array. The -3dB elevation focus resulting from a TPX lens was measured to be 152 microns at the focal depth (~7mm).

A piezoelectric bone-conduction bending hearing actuator

A prototype of a novel bone-conduction hearing actuator based on a piezoelectric bending actuator is presented. The device lies flat against the skull which would allow it to form the basis of a subcutaneous bone-anchored hearing aid. The actuator excites bending in bone through a local bending moment rather than the application of a point force as with conventional bone-anchored hearing aids. Through measurements of the cochlear velocity created by the actuator in embalmed human heads, the device is shown to exhibit high efficiency, making it a possible alternative to present-day electromagnetic bone-vibration actuators.