Sachin Katti

XORs in the air: practical wireless network coding

This paper proposes COPE, a new architecture for wireless mesh networks. In addition to forwarding packets, routers mix (i.e., code) packets from different sources to increase the information content of each transmission. We show that intelligently mixing packets increases network throughput. Our design is rooted in the theory of network coding. Prior work on network coding is mainly theoretical and focuses on multicast traffic. This paper aims to bridge theory with practice; it addresses the common case of unicast traffic, dynamic and potentially bursty flows, and practical issues facing the integration of network coding in the current network stack. We evaluate our design on a 20-node wireless network, and discuss the results of the first testbed deployment of wireless network coding. The results show that using COPE at the forwarding layer, without modifying routing and higher layers, increases network throughput. The gains vary from a few percent to several folds depending on the traffic pattern, congestion level, and transport protocol.

Embracing wireless interference: analog network coding

Traditionally, interference is considered harmful. Wireless networks strive to avoid scheduling multiple transmissions at the same time in order to prevent interference. This paper adopts the opposite approach; it encourages strategically picked senders to interfere. Instead of forwarding packets, routers forward the interfering signals. The destination leverages network-level information to cancel the interference and recover the signal destined to it. The result is analog network coding because it mixes signals not bits. So, what if wireless routers forward signals instead of packets? Theoretically, such an approach doubles the capacity of the canonical 2-way relay network. Surprisingly, it is also practical. We implement our design using software radios and show that it achieves significantly higher throughput than both traditional wireless routing and prior work on wireless network coding.

Achieving single channel, full duplex wireless communication

This paper discusses the design of a single channel full-duplex wireless transceiver. The design uses a combination of RF and baseband techniques to achieve full-duplexing with minimal effect on link reliability. Experiments on real nodes show the full-duplex prototype achieves median performance that is within 8% of an ideal full-duplexing system. This paper presents Antenna Cancellation, a novel technique for self-interference cancellation. In conjunction with existing RF interference cancellation and digital baseband interference cancellation, antenna cancellation achieves the amount of self-interference cancellation required for full-duplex operation. The paper also discusses potential MAC and network gains with full-duplexing. It suggests ways in which a full-duplex system can solve some important problems with existing wireless systems including hidden terminals, loss of throughput due to congestion, and large end-to-end delays.

Full duplex radios

This paper presents the design and implementation of the first in-band full duplex WiFi radios that can simultaneously transmit and receive on the same channel using standard WiFi 802.11ac PHYs and achieves close to the theoretical doubling of throughput in all practical deployment scenarios. Our design uses a single antenna for simultaneous TX/RX (i.e., the same resources as a standard half duplex system). We also propose novel analog and digital cancellation techniques that cancel the self interference to the receiver noise floor, and therefore ensure that there is no degradation to the received signal. We prototype our design by building our own analog circuit boards and integrating them with a fully WiFi-PHY compatible software radio implementation. We show experimentally that our design works robustly in noisy indoor environments, and provides close to the expected theoretical doubling of throughput in practice.

Practical, real-time, full duplex wireless

This paper presents a full duplex radio design using signal inversion and adaptive cancellation. Signal inversion uses a simple design based on a balanced/unbalanced (Balun) transformer. This new design, unlike prior work, supports wideband and high power systems. In theory, this new design has no limitation on bandwidth or power. In practice, we find that the signal inversion technique alone can cancel at least 45dB across a 40MHz bandwidth. Further, combining signal inversion cancellation with cancellation in the digital domain can reduce self-interference by up to 73dB for a 10MHz OFDM signal. This paper also presents a full duplex medium access control (MAC) design and evaluates it using a testbed of 5 prototype full duplex nodes. Full duplex reduces packet losses due to hidden terminals by up to 88%. Full duplex also mitigates unfair channel allocation in AP-based networks, increasing fairness from 0.85 to 0.98 while improving downlink throughput by 110% and uplink throughput by 15%. These experimental results show that a re- design of the wireless network stack to exploit full duplex capability can result in significant improvements in network performance.

Resilient network coding in the presence of Byzantine adversaries

Network coding substantially increases network throughput. But since it involves mixing of information inside the network, a single corrupted packet generated by a malicious node can end up contaminating all the information reaching a destination, preventing decoding. This paper introduces the first distributed polynomial-time rate-optimal network codes that work in the presence of Byzantine nodes. We present algorithms that target adversaries with different attacking capabilities. When the adversary can eavesdrop on all links and jam zO links , our first algorithm achieves a rate of C - 2zO, where C is the network capacity. In contrast, when the adversary has limited snooping capabilities, we provide algorithms that achieve the higher rate of C - zO. Our algorithms attain the optimal rate given the strength of the adversary. They are information-theoretically secure. They operate in a distributed manner, assume no knowledge of the topology, and can be designed and implemented in polynomial-time. Furthermore, only the source and destination need to be modified; non-malicious nodes inside the network are oblivious to the presence of adversaries and implement a classical distributed network code. Finally, our algorithms work over wired and wireless networks.

Applications of self-interference cancellation in 5G and beyond

Self-interference cancellation invalidates a long-held fundamental assumption in wireless network design that radios can only operate in half duplex mode on the same channel. Beyond enabling true in-band full duplex, which effectively doubles spectral efficiency, self-interference cancellation tremendously simplifies spectrum management. Not only does it render entire ecosystems like TD-LTE obsolete, it enables future networks to leverage fragmented spectrum, a pressing global issue that will continue to worsen in 5G networks. Self-interference cancellation offers the potential to complement and sustain the evolution of 5G technologies toward denser heterogeneous networks and can be utilized in wireless communication systems in multiple ways, including increased link capacity, spectrum virtualization, any-division duplexing (ADD), novel relay solutions, and enhanced interference coordination. By virtue of its fundamental nature, self-interference cancellation will have a tremendous impact on 5G networks and beyond.

SoftRAN: software defined radio access network

An important piece of the cellular network infrastructure is the radio access network (RAN) that provides wide-area wireless connectivity to mobile devices. The fundamental problem the RAN solves is figuring out how best to use and manage limited spectrum to achieve this connectivity. In a dense wireless deployment with mobile nodes and limited spectrum, it becomes a difficult task to allocate radio resources, implement handovers, manage interference, balance load between cells, etc. We argue that LTEs current distributed control plane is suboptimal in achieving the above objective. We propose SoftRAN, a fundamental rethink of the radio access layer. SoftRAN is a software defined centralized control plane for radio access networks that abstracts all base stations in a local geographical area as a virtual big-base station comprised of a central controller and radio elements (individual physical base stations). In defining such an architecture, we create a framework through which a local geographical network can effectively perform load balancing and interference management, as well as maximize throughput, global utility, or any other objective.

Symbol-level network coding for wireless mesh networks

This paper describes MIXIT, a system that improves the throughput of wireless mesh networks. MIXIT exploits a basic property of mesh networks: even when no node receives a packet correctly, any given bit is likely to be received by some node correctly. Instead of insisting on forwarding only correct packets, MIXIT routers use physical layer hints to make their best guess about which bits in a corrupted packet are likely to be correct and forward them to the destination. Even though this approach inevitably lets erroneous bits through, we find that it can achieve high throughput without compromising end-to-end reliability. The core component of MIXIT is a novel network code that operates on small groups of bits, called symbols. It allows the nodes to opportunistically route groups of bits to their destination with low overhead. MIXITs network code also incorporates an end-to-end error correction component that the destination uses to correct any errors that might seep through. We have implemented MIXIT on a software radio platform running the Zigbee radio protocol. Our experiments on a 25-node indoor testbed show that MIXIT has a throughput gain of 2.8x over MORE, a state-of-the-art opportunistic routing scheme, and about 3.9x over traditional routing using the ETX metric.

pFabric: minimal near-optimal datacenter transport

In this paper we present pFabric, a minimalistic datacenter transport design that provides near theoretically optimal flow completion times even at the 99th percentile for short flows, while still minimizing average flow completion time for long flows. Moreover, pFabric delivers this performance with a very simple design that is based on a key conceptual insight: datacenter transport should decouple flow scheduling from rate control. For flow scheduling, packets carry a single priority number set independently by each flow; switches have very small buffers and implement a very simple priority-based scheduling/dropping mechanism. Rate control is also correspondingly simpler; flows start at line rate and throttle back only under high and persistent packet loss. We provide theoretical intuition and show via extensive simulations that the combination of these two simple mechanisms is sufficient to provide near-optimal performance.