Seongyop Lim

Direct synthesis and structural analysis of nitrogen-doped carbon nanofibers.

Carbon nanofibers containing a range of nitrogen contents of 1-10 atom % were directly synthesized by catalytic chemical vapor deposition over nickel-based catalysts at 350-600 degrees C using acetonitrile and acrylonitrile. The nitrogen content was controlled by careful choice of the reaction conditions. The N-doped carbon nanofibers showed herringbone structure with 20-60 nm diameter. X-ray photoelectron spectroscopy was applied to examine the chemical state of nitrogen in carbon nanofibers. Structural features of N-doped carbon nanofibers were examined in X-ray diffraction and electron microscopy. The mechanism for nitrogen including the structure of carbon nanofibers through the catalysis was discussed on the basis of the results.

Electrocatalytic effects of carbon dissolution in Pd nanoparticles.

Highly dispersed Pd nanoparticles were prepared by borohydride reduction of Pd(acac)(2) in 1,2-propanediol at an elevated temperature. They were uniformly dispersed on carbon black without significant aggregation. X-ray diffraction showed that carbons from the Pd precursor dissolved in Pd, increasing its lattice parameter. A modified reduction process was tested to remove the carbon impurities. Carbon removal greatly enhanced catalytic activity toward the oxygen reduction reaction. It also generated an inconsistency between the electronic modifications obtained from X-ray photoelectron spectroscopy and the electrochemical method. CO displacement measurements showed that the formation of Pd-C bonds decreased the work function of the surface Pd atoms.

Preparation and Characteristics of SiOx Coated Carbon Nanotubes with High Surface Area.

An easy method to synthesize SiOx coated carbon nanotubes (SiOx-CNT) through thermal decomposition of polycarbomethylsilane adsorbed on the surface of CNTs is reported. Physical properties of SiOx-CNT samples depending on various Si contents and synthesis conditions are examined by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen isotherm, scanning electron microscope (SEM), and transmission electron microscope (TEM). Morphology of the SiOx-CNT appears to be perfectly identical to that of the pristine CNT. It is confirmed that SiOx is formed in a thin layer of approximately 1 nm thickness over the surface of CNTs. The specific surface area is significantly increased by the coating, because thin layer of SiOx is highly porous. The surface properties such as porosity and thickness of SiOx layers are found to be controlled by SiOx contents and heat treatment conditions. The preparation method in this study is to provide useful nano-hybrid composite materials with multi-functional surface properties.

Characterization and Performance of MEA for Direct Methanol Fuel Cell Prepared with PFA Grafted Polystyrene Membranes via Radiation-Grafting Method

In order to develop a novel polymer electrolyte membrane for direct methanol fuel cell (DMFC), styrene monomer was graft-polymerized into poly(tetrafluoroethylene perfluoropropyl vinyl ether) (PFA) film followed by a sulfonation reaction. The graft polymerization was prepared by the -ray radiation-grafting method. Subsequently, sulfonation of the radiation-grafted film was carried out in a chlorosulfonic acid/1,2-dichloroethane (2 v/v%) solution. The chemical, physical, electrochemical and morphological properties of the radiation-grafted membranes (PFA-g-PSSA) were characterized by fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The water uptake, ionic conductivity, and methanol permeability of the PFA-g-PSSA membrane were also measured. The cell performances of MEA prepared with the PFA-g-PSSA membranes were evaluated and the cell resistances were measured by an impedance analyzer. The MEA using PFA-g-PSSA membranes showed superior performance for DMFCs in comparison with the commercial Nafion 112 membrane.

Performance of Membrane Electrode Assembly for DMFC Prepared by Bar-Coating Method

직접메탄올 연료전지 (DMFC)의 핵심 구성 요소 중에서 하나는 고분자 전해질막과 촉매층 (연료극과 공기극)으로 구성된 전해질/전극 접합체 (MEA)이다. 그중에서 촉매층은 브러싱법, 전시법, 스프레이 코팅법, 스크린 프린팅법과 같은 다양한 방법을 사용하여 carbon paper나 carbon cloth등과 같은 전극 지지체 위에 코팅한다. 그러나 이러한 촉매 코팅방법들은 전극 지지체 위에 촉매를 균일한 두께로 코팅하기 어렵고, 촉매의 손실이 많으며, 또한 코팅 시간이 많이 필요하다는 단점들이 있다. 본 연구에서는 DMFC용 MEA의 전극층을 바코팅 방법 (bar-coating method)을 사용하여 한 번에 원하는 양의 촉매가 코팅되도록 제조하였다. 이렇게 제조한 전극 촉매층 표면과 단면의 형태를 SEM을 사용하여 관찰하였다. 제조한 MEA의 성능과 저항은 단위전지와 임피던스 분석기를 사용하여 측정하였다. 【The key component of a direct methanol fuel cell (DMFC) is the membrane electrode assembly (MEA), which comprises a polymer electrolyte membrane and catalyst layers (anode and cathode electrode). Generally the catalyst layer is coated on the porous electrode supporter (e.g. carbon paper or cloth) using various coating methods such as brushing, decal transfer, spray coating and screen printing methods. However, these methods were disadvantageous in terms of the uniformity of catalyst layer thickness, catalyst loss, and coating time. In this work, we used bar-coating method which can prepare the catalyst layer with uniform thickness for MEA of DMFC. The surface and cross-section morphologies of the catalyst layers were observed by SEM. The performances and resistance of the MEAs were investigated through a single cell evaluation and impedance analyzer.】

Effect of Carbon Felt Oxidation Methods on the Electrode Performance of Vanadium Redox Flow Battery

레독스 흐름 전지의 전극으로 사용하기 위해 탄소펠트를 열처리와 산처리 방법으로 산화 개질하였다. 열중량 분석결과 열처리 또는 산처리에 의하여 탄소펠트의 섬유 표면에 고분자 물질이 제거되고 산소 관능기가 도입된 것을 확인할 수 있었으며 습식 방법인 산처리 방법보다 건식방법인 열처리 방법이 기계적 안정성을 유지하는데 효과적인 처리 방법으로 나타났다. XPS, 원소분석을 통하여 500

Corrosion Resistance, Cell Performance and Long-term Stability of Metal Bipolar Plates for Direct Methanol Fuel Cell

^{\circ}C

KOH activation of carbon nanofibers

에서 4시간 열처리한 탄소펠트의 표면에 산소 관능기가 부가된 것을 확인하였으며 질소흡착실험에서 거의 없던 표면적이 96

Crystal Structures and Growth Mechanisms of Au@Ag Core−Shell Nanoparticles Prepared by the Microwave−Polyol Method

m^2/g

Fast Preparation of PtRu Catalysts Supported on Carbon Nanofibers by the Microwave-Polyol Method and Their Application to Fuel Cells

로 증가한 것을 알 수 있었다. CV실험 및 분극 실험을 수행한 결과 500