Shengji Xia

Oxidative degradation of dimethyl phthalate (DMP) by UV/H2O2 process.

The photochemical degradation of dimethyl phthalate (DMP) in UV/H(2)O(2) advanced oxidation process was studied and a kinetic model based on the elementary reactions involved was developed in this paper. Relatively slow DMP degradation was observed during UV radiation, while DMP was not oxidized by H(2)O(2) alone. In contrast, the combined UV/H(2)O(2) process could effectively degraded DMP, which is attributed to the strong oxidation strength of hydroxyl radical produced. Results show that DMP degradation rate was affected by H(2)O(2) concentration, intensity of UV radiation, initial DMP concentration, and solution pH. A kinetic model without the pseudo-steady state assumption was established according to the generally accepted elementary reactions in UV/H(2)O(2) advanced oxidation process. The rate constant for the reaction between DMP and hydroxyl radical was found to be 4.0 x 10(9) M(-1)s(-1) through fitting the experimental data to this model. The kinetic model could adequately describe the influence of key factors on DMP degradation rate in UV/H(2)O(2) advanced oxidation process, and could serve as a guide in designing treatment systems for DMP removal.

Measurement of dissolved organic nitrogen in a drinking water treatment plant: Size fraction, fate, and relation to water quality parameters

This paper investigates the characteristics of dissolved organic nitrogen (DON) in raw water from the Huangpu River and also in water undergoing treatment in the full-scale Yangshupu drinking water treatment plant (YDWTP) in Shanghai, China. The average DON concentration of the raw water was 0.34 mg/L, which comprised a relatively small portion (~5%) of the mass of total dissolved nitrogen (TDN). The molecular weight (MW) distribution of dissolved organic matter (DOM) was divided into five groups: >30, 10-30, 3-10, 1-3 and <1 kDa using a series of ultrafiltration membranes. Dissolved organic carbon (DOC), UV absorbance at wavelength of 254 nm (UV254) and DON of each MW fraction were analyzed. DON showed a similar fraction distribution as DOC and UV254. The <1 kDa fraction dominated the composition of DON, DOC and UV254 as well as the major N-nitrosodimethylamine formation potential (NDMAFP) in the raw water. However, this DON fraction cannot be effectively removed in the treatment line at the YDWTP including pre-ozonation, clarification and sand filtration processes. The results from linear regression analysis showed that DON is moderately correlated to DOC, UV254 and trihalomethane formation potential (FP), and strongly correlated to haloacetic acids FP and NDMAFP. Therefore, DON could serve as a surrogate parameter to evaluate the reactivity of DOM and disinfection by-products FP.

Measurements of dissolved organic nitrogen (DON) in water samples with nanofiltration pretreatment.

Dissolved organic nitrogen (DON) measurements for water samples with a high dissolved inorganic nitrogen (DIN, including nitrite, nitrate and ammonia) to total dissolved nitrogen (TDN) ratio using traditional methods are inaccurate due to the cumulative analytical errors of independently measured nitrogen species (TDN and DIN). In this study, we present a nanofiltration (NF) pretreatment to increase the accuracy and precision of DON measurements by selectively concentrating DON while passing through DIN species in water samples to reduce the DIN/TDN ratio. Three commercial NF membranes (NF90, NF270 and HL) were tested. The rejection efficiency of finished water from the Yangshupu drinking water treatment plant (YDWTP) is 12%, 31%, 8% of nitrate, 26%, 28%, 23% of ammonia, 77%, 78%, 82% of DOC (dissolved organic carbon), and 83%, 87% 88% of UV(254) for HL, NF90 and NF270, respectively. NF270 showed the best performance due to its high DIN permeability and DON retention (∼80%). NF270 can lower the DIN/TDN ratio from around 1 to less than 0.6 mg N/mg N, and satisfactory DOC recoveries as well as DON measurements in synthetic water samples were obtained using optimized operating parameters. Compared to the available dialysis pretreatment method, the NF pretreatment method shows a similar improved performance for DON measurement for aqueous samples and can save at least 20 h of operating time and a large volume of deionized water, which is beneficial for laboratories involved in DON analysis. DON concentration in the effluent of different treatment processes at the YDWTP and the SDWTP (Shijiuyang DWTP) in China were investigated with and without NF pretreatment; the results showed that DON with NF pretreatment and DOC both gradually decreased after each water treatment process at both treatment plants. The advanced water treatment line, including biological pretreatment, clarification, sand filtration, ozone-BAC processes at the SDWTP showed greater efficiency of DON removal from 0.37 to 0.11 mg N L(-1) than that at the YDWTP, including pre-ozonation, clarification and sand filtration processes from 0.18 to 0.11 mg N L(-1).

Formation of iodinated disinfection by-products during oxidation of iodide-containing water with potassium permanganate

This study shows that iodinated disinfection by-products (I-DBPs) including iodoform (IF), iodoacetic acid (IAA) and triiodoacetic acid (TIAA) can be produced when iodide-containing waters are in contact with potassium permanganate. IF was found as the major I-DBP species during the oxidation. Iodide was oxidized to HOI, I(2) and I(3)(-), consequently, which led to the formation of iodinated organic compounds. I-DBPs varied with reaction time, solution pH, initial concentrations of iodide and potassium permanganate. Yields of IF, IAA and TIAA increased with reaction time and considerable I-DBPs were formed within 12 h. Peak IF yields were found at circumneutral pH range. However, formation of IAA and TIAA was favored under acidic conditions. Molar ratio of iodide to potassium permanganate showed significant influence on formation of IF, IAA and TIAA. The formation of IF, IAA and TIAA also depended on the characteristics of the waters.

Chlorination of chlortoluron: Kinetics, pathways and chloroform formation

Chlortoluron chlorination is studied in the pH range of 3-10 at 25 ± 1°C. The chlorination kinetics can be well described by a second-order kinetics model, first-order in chlorine and first-order in chlortoluron. The apparent rate constants were determined and found to be minimum at pH 6, maximum at pH 3 and medium at alkaline conditions. The rate constant of each predominant elementary reactions (i.e., the acid-catalyzed reaction of chlortoluron with HOCl, the reaction of chlortoluron with HOCl and the reaction of chlortoluron with OCl(-)) was calculated as 3.12 (± 0.10)×10(7)M(-2)h(-1), 3.11 (±0.39)×10(2)M(-1)h(-1) and 3.06 (±0.47)×10(3)M(-1)h(-1), respectively. The main chlortoluron chlorination by-products were identified by gas chromatography-mass spectrometry (GC-MS) with purge-and-trap pretreatment, ultra-performance liquid chromatography-electrospray ionization-MS and GC-electron capture detector. Six volatile disinfection by-products were identified including chloroform (CF), dichloroacetonitrile, 1,1-dichloropropanone, 1,1,1-trichloropropanone, dichloronitromethane and trichloronitromethane. Degradation pathways of chlortoluron chlorination were then proposed. High concentrations of CF were generated during chlortoluron chlorination, with maximum CF yield at circumneutral pH range in solution.

Ametryn degradation by aqueous chlorine: kinetics and reaction influences.

The chemical oxidation of the herbicide ametryn was investigated by aqueous chlorination between pH 4 and 10 at a temperature of 25 degrees C. Ametryn was found to react very rapidly with aqueous chlorine. The reaction kinetics can be well described by a second-order kinetic model. The apparent second-order rate constants are greater than 5 x 10(2)M(-1)s(-1) under acidic and neutral conditions. The reaction proceeds much more slowly under alkaline conditions. The predominant reactions were found to be the reactions of HOCl with neutral ametryn and the charged ametryn, with rate constants equal to 7.22 x 10(2) and 1.58 x 10(3)M(-1)s(-1), respectively. The ametryn degradation rate increases with addition of bromide and decreases with addition of ammonia during the chlorination process. Based on elementary chemical reactions, a kinetic model of ametryn degradation by chlorination in the presence of bromide or ammonia ion was also developed. By employing this model, we estimate that the rate constants for the reactions of HOBr with neutral ametryn and charged ametryn were 9.07 x 10(3) and 3.54 x 10(6)M(-1)s(-1), respectively. These values are 10- to 10(3)-fold higher than those of HOCl, suggesting that the presence of bromine species during chlorination could significantly accelerate ametryn degradation.

Degradation kinetics and chloropicrin formation during aqueous chlorination of dinoseb.

The kinetics of chlorination of dinoseb and the corresponding formation of disinfection by-products (DBPs) were studied between pH 4 and 9 at room temperature (25±1°C). The reactivity shows a minimum at pH 9, a maximum at pH 4 and a medium at neutral conditions. pH profile of the apparent second-order rate constant of the reaction of dinoseb with chlorine was modeled considering the elementary reactions of HOCl with dinoseb species and an acid-catalyzed reaction. The predominant reactions at near neutral pH were the reactions of HOCl with the two species of dinoseb. The rate constants of 2.0 (±0.8)×10(4)M(-2)s(-1), 3.3 (±0.6) and 0.5 (±0.1)M(-1)s(-1) were determined for the acid-catalyzed reaction, HOCl reacted with dinoseb and dinoseb(-), respectively. The main degradation by-products of the dinoseb formed during chlorination have been separated and identified by GC-MS with liquid-liquid extraction sample pretreatment. Six volatile and semi-volatile DBPs were identified in the chlorination products, including chloroform (CF), monochloroacetone, chloropicrin (TCNM), 1,1-dichloro-2-methy-butane, 1,2-dichloro-2-methy-butane, 1-chloro-3-methy-pentanone. A proposed degradation pathway of dinoseb during chlorination was then given. TCNM and CF formation potential during chlorination of dinoseb reached as high as 0.077 and 0.097μMμM(-1) dinoseb under the traditional condition (pH=7 and Cl2/C=2). Their yields varied with Cl2/C, pH and time. The maximum yields of TCNM appeared at molar ratio as Cl2/C=1 and pH 3, while the maximum of CF appeared at molar ratio as Cl2/C=4 and pH 7. [TCNM]/[CF] decreased with reaction time and increased solution pH.

Degradation kinetics and N-Nitrosodimethylamine formation during monochloramination of chlortoluron

The degradation of chlortoluron by monochloramination was investigated in the pH range of 4-9. The degradation kinetics can be well described by a second-order kinetic model, first-order in monochloramine (NH(2)Cl) and first-order in chlortoluron. NH(2)Cl was found not to be very reactive with chlortoluron, and the apparent rate constants in the studied conditions were 2.5-66.3M(-1)h(-1). The apparent rate constants were determined to be maximum at pH 6, minimum at pH 4 and medium at alkaline conditions. The main disinfection by-products (DBPs) formed after chlortoluron monochloramination were identified by ultra performance liquid chromatography-ESI-MS and GC-electron capture detector. N-Nitrosodimethylamine (NDMA) and 5 volatile chlorination DBPs including chloroform (CF), dichloroacetonitrile, 1,1-dichloropropanone, 1,1,1-trichloropropanone and trichloronitromethane were identified. The distributions of DBPs formed at different solution pH were quite distinct. Concentrations of NDMA and CF were high at pH 7-9, where NH(2)Cl was the main disinfectant in the solution. NDMA formation during chlortoluron monochloramination with the presence of nitrogenous salts increased in the order of nitrite

Ultrafiltration of humic acid and surface water with tubular ceramic membrane

Abstract In recent years, the ceramic membrane filtration has become increasingly attractive for drinking water production. The flux evolution and retention performance of a tubular ceramic membrane with nominal pore size of 0.01 μm was systematically investigated. Filtration experiments were carried out on a pilot-scale crossflow unit using humic acid (HA) solution and surface water as feed by varying transmembrane pressure (TMP). Measurements such as total organic carbon (TOC), ultraviolet absorbance at 254 nm (UV254), fluorescence excitation emission matrices (EEMs), pH, and conductivity were made on both raw water and the permeate. During filtration, flux declined drastically in the beginning stage due to fouling and proceeded to a pseudostable flux. In the low HA concentration, the flux decreased in the first 30 min for about 36, 48, 50 and 51% with the TMP of 0.5, 0.8, 1.0, and 1.2 bar, respectively, while it came to 47, 52, 57, and 65%, respectively for relatively high concentrations; the steady fl...

Preparation polyamide nanofiltration membrane by interfacial polymerization

Abstract Nanofiltration (NF) composite membrane was prepared by interfacial polymerization of 1,6-hexylenediamime, o-phenylenediamine or piperazine with trimesoyl chloride (TMC) on the surface of polysulfone support, respectively. Meanwhile, two polysulfone support membranes with different molecular weight cut off (MWCO) were introduced into this experiment, hoping to find the influence of porous substrates on the prepared membrane performance. Furthermore, the water flux and salt rejection rate of those three kinds of newly-prepared NF composite membranes were compared by water filtration experiment. In order to make interfacial polymerization much more effective, kinds of reaction ratios between piperazine and TMC were designed. It can be seen from the results that piperazine reacts better with TMC compared to the other two chemical medicines, and the salt rejection rate of poly (piperazine) NF composite membranes can arrive at 55% under the condition of laboratory; however, the effects of polysulfone s...