Sofia Rangou

Formation of Integral Asymmetric Membranes of AB Diblock and ABC Triblock Copolymers by Phase Inversion

The formation of integral asymmetric membranes from ABC triblock terpolymers by non-solvent-induced phase separation is shown. They are compared with the AB diblock copolymer precursors. Triblock terpolymers of polystyrene-block-poly(2-vinylpyridine)-block-poly(ethylene oxide) (PS-b-P2VP-b-PEO) with two compositions are investigated. The third block supports the formation of a membrane in a case, where the corresponding diblock copolymer does not form a good membrane. In addition, the hydrophilicity is increased by the third block and due to the hydroxyl group the possibility of post-functionalization is given. The morphologies are imaged by scanning electron microscopy. The influence of the PEO on the membrane properties is analyzed by water flux, retention, and dynamic contact angle measurements.

Carbohydrates as additives for the formation of isoporous PS-b-P4VP diblock copolymer membranes.

Highly porous polystyrene-block-poly(4-vinylpyridine) (PS-b-P4VP) diblock copolymer membranes are prepared using carbohydrates as additives. Therefore α-cyclodextrine, α-(D)-glucose, and saccharose (cane sugar) are tested for the membrane formation of three different PS-b-P4VP polymers. The addition of the carbohydrates leads to an increasing viscosity of the membrane solutions due to hydrogen bonding between hydroxyl groups of the carbohydrates and pyridine units of the block copolymer. In all cases, the membranes made from solution with carbohydrates have higher porosity, an improved narrow pore distribution on the surface and a higher water flux as membranes made without carbohydrates with the same polymer, solvent ratio, and polymer concentration.

Continuous Equilibrated Growth of Ordered Block Copolymer Thin Films by Electrospray Deposition

Deposition of block copolymer thin films is most often accomplished in a serial process where material is spin coated onto a substrate and subsequently annealed, either thermally or by solvent vapor, to produce a well-ordered morphology. Here we show that under appropriate conditions, well-ordered block copolymer films may be continuously grown under substrate equilibrated conditions by slow deposition of discrete subattoliter quantities of material using electrospray. We conduct time-resolved observations and investigate the effects of process parameters that underpin film morphology including solvent selectivity, substrate temperature, block-substrate selectivity, and flow rate of the feed solution. For a PEO cylinder-forming poly(styrene-b-ethylene oxide) block copolymer, we uncover a wide temperature window from 90 to 150 °C and an ideal flow rate of 2 μL/min for ordered film deposition from dilute acetone solutions. PEO cylinders aligned with their long axes perpendicular to the film-air interface at optimal spray conditions. Using poly(styrene-b-methyl methacrylate) deposited onto neutrally selective surfaces, we show that the substrate-equilibrated process results in vertically oriented microdomains throughout the film, indicating a preservation of the initial substrate-dictated morphology during the film deposition. Electrospray offers a new and potentially exciting route for controlled, continuous growth of block copolymer thin films and manipulation of their microstructure.

Morphologies of ABC Triblock Terpolymer Melts Containing Poly(Cyclohexadiene): Effects of Conformational Asymmetry

We have synthesized linear ABC triblock terpolymers containing poly(1,3-cyclohexadiene), PCHD, as an end block and characterized their morphologies in the melt. Specifically, we have studied terpolymers containing polystyrene (PS), polybutadiene (PB), and polyisoprene (PI) as the other blocks. Systematically varying the ratio of 1,2- /1,4-microstructures of poly(1,3-cyclohexadiene), we have studied the effects of conformational asymmetry among the three blocks on the morphologies using transmission electron microscopy (TEM), small-angle X-ray scattering (SAXS), and self-consistent field theory (SCFT) performed with PolySwift++. Our work reveals that the triblock terpolymer melts containing a high percentage of 1,2-microstructures in the PCHD block are disordered at 110 °C for all the samples, independent of sequence and volume fraction of the blocks. In contrast, the triblock terpolymer melts containing a high percentage of 1,4-microstructure form regular morphologies known from the literature. The accuracy of the SCFT calculations depends on calculating the χ parameters that quantify the repulsive interactions between different monomers. Simulations using χ values obtained from solubility parameters and group contribution methods are unable to reproduce the morphologies as seen in the experiments. However, SCFT calculations accounting for the enhancement of the χ parameter with an increase in the conformational asymmetry lead to an excellent agreement between theory and experiments. These results highlight the importance of conformational asymmetry in tuning the χ parameter and, in turn, morphologies in block copolymers.

Claisen thermally rearranged (CTR) polymers.

Second generation of thermally rearranged polymers presents low temperatures for a complete rearrangement. Thermally rearranged (TR) polymers, which are considered the next-generation of membrane materials because of their excellent transport properties and high thermal and chemical stability, are proven to have significant drawbacks because of the high temperature required for the rearrangement and low degree of conversion during this process. We demonstrate that using a [3,3]-sigmatropic rearrangement, the temperature required for the rearrangement of a solid glassy polymer was reduced by 200°C. Conversions of functionalized polyimide to polybenzoxazole of more than 97% were achieved. These highly mechanically stable polymers were almost five times more permeable and had more than two times higher degrees of conversion than the reference polymer treated under the same conditions. Properties of these second-generation TR polymers provide the possibility of preparing efficient polymer membranes in a form of, for example, thin-film composite membranes for various gas and liquid membrane separation applications.

Nanocomposites of Polystyrene-b-Poly(isoprene)-b-Polystyrene Triblock Copolymer with Clay–Carbon Nanotube Hybrid Nanoadditives

Polystyrene-b-polyisoprene-b-polystyrene (PS-b-PI-b-PS), a widely used linear triblock copolymer of the glassy-rubbery-glassy type, was prepared in this study by anionic polymerization and was further used for the development of novel polymer nanocomposite materials. Hybrid nanoadditives were prepared by the catalytic chemical vapor deposition (CCVD) method through which carbon nanotubes were grown on the surface of smectite clay nanolayers. Side-wall chemical organo-functionalization of the nanotubes was performed in order to enhance the chemical compatibilization of the clay-CNT hybrid nanoadditives with the hydrophobic triblock copolymer. The hybrid clay-CNT nanoadditives were incorporated in the copolymer matrix by a simple solution-precipitation method at two nanoadditive to polymer loadings (one low, i.e., 1 wt %, and one high, i.e., 5 wt %). The resulting nanocomposites were characterized by a combination of techniques and compared with more classical nanocomposites prepared using organo-modified clays as nanoadditives. FT-IR and Raman spectroscopies verified the presence of the hybrid nanoadditives in the final nanocomposites, while X-ray diffraction and transmission electron microscopy proved the formation of fully exfoliated structures. Viscometry measurements were further used to show the successful incorporation and homogeneous dispersion of the hybrid nanoadditives in the polymer mass. The so prepared nanocomposites exhibited enhanced mechanical properties compared to the pristine polymer and the nanocomposites prepared by conventional organo-clays. Both tensile stress and strain at break were improved probably due to better interfacial adhesion of the clay-CNT hybrid of the flexible rubbery PI middle blocks of the triblock copolymer matrix.

Morphology and elasticity of polystyrene-block-polyisoprene diblock copolymers in the melt

The influence of morphology on the viscoelastic properties of melts of microphase-separated polystyrene-block-polyisoprene (PS-b-PI) diblock copolymers was investigated in oscillatory shear and creep recovery experiments. By means of anionic polymerization, three PS-b-PI diblock copolymers with a narrow molecular weight distribution and different types of morphology (spherical, cylindrical and lamellar microstructure) were prepared. Linear viscoelastic shear oscillations and creep recovery experiments in shear were performed in order to determine the elastic and viscous properties of the diblock copolymers in the melt at small and large time scales. Our analysis reveals that melts of diblock copolymers are characterized by a pronounced elastic behavior leading to a relatively large recoverable deformation in creep recovery experiments. The elasticity of the diblock copolymers is also revealed by the appearance of the creep-ringing effect. Morphological investigations were carried out to establish relations between microstructure and melt elasticity. Since ordering phenomena take place in melts of diblock copolymers until an equilibrium morphology is achieved, the storage modulus G′ of diblock copolymer melts increases with time up to a steady-state value.

Analysis of glass transition and relaxation processes of low molecular weight polystyrene-b-polyisoprene diblock copolymers

The objective of this study is to analyze the glass transition temperature and relaxation processes of low molecular weight polystyrene-block-polyisoprene diblock copolymers with different compositions, synthesized via anionic polymerization. Thermal properties were investigated by differential scanning calorimetry and dynamic-mechanical thermal analysis, while the morphologies at room temperature were investigated by transmission electron microscopy and small-angle X-ray scattering. The χN values indicate that the diblock copolymers lie near the weak segregation regime. Three different experimental techniques were applied to determine the dynamic properties, i.e., linear viscoelastic shear oscillations, creep recovery experiments, and dielectric spectroscopy. The rheological experiments were performed above the order–disorder transition temperature where the diblock copolymers behave like a Maxwell fluid. Our results indicate that the presence of the polyisoprene segments strongly influences the monomeric friction coefficient and the tendency to form entanglements above the order–disorder temperature. Consequently, the zero-shear rate viscosity of a diblock copolymer is much lower than the zero-shear rate viscosity of the neat polystyrene block (the polystyrene precursor of the polymerization procedure). Dielectric spectroscopy enables the analysis of relaxation processes below the glass transition of the polystyrene microphase. Frequency sweeps indicate the dynamic glass transition of the polyisoprene blocks, which are partly mixed with the polystyrene blocks, which are always the majority component in the block copolymers of this study.

Novel Post-Treatment Approaches to Tailor the Pore Size of PS-b-PHEMA Isoporous Membranes

Using the example of an integral-asymmetric isoporous membrane prepared from polystyrene-block-poly(2-hydroxyethyl methacrylate) (PS-b-PHEMA), physical and chemical ways of post-treatment are introduced with the aim to tailor the pore size. These post-treatments are i) thermal annealing and ii) urethane chemistry of ethyl isocyanate (EI) in the presence of perfluoro(methyl cyclohexane). Via these approaches, the pore size of PS-b-PHEMA membranes is successfully tailored in the range of 10-20 nm with narrow pore size distribution by controlling the duration of thermal annealing and chemical reaction, respectively. The excellent hydrophilicity of the PS-b-PHEMA membrane is not changed by thermal annealing. The chemical postmodification using EI is associated with a loss of hydrophilicity with increasing conversion.

Analysis of stability and viscoelastic properties of melts of polystyrene-block-polyisoprene diblock copolymers in oscillatory shear and creep-recovery experiments

In this study, the rheological properties of polystyrene-block-polyisoprene (PS-b-PI) diblock copolymer melts with different types of morphology are analysed. Using the technique of anionic polymerization three different PS-b-PI diblock copolymers with a spherical, cylindrical and lamellar morphology, respectively, were synthesised. The objective of our study was to determine the viscous and elastic properties of these PS-b-PI diblock copolymers and to investigate the influence of morphology on the viscoelastic properties at short and long times. The analysis of our experiments reveals that morphological changes take place in the melt which lead to changes of the dynamic moduli. Furthermore, all three diblock copolymers of this study reveal a non-terminal behaviour in oscillatory shear flow in the microphase-separated state. Our creep recovery experiments indicate that microphase-separated diblock copolymers are characterised by a pronounced recoverable deformation.