Timothy J. Strathmann

Chemical properties of biocrude oil from the hydrothermal liquefaction of Spirulina algae, swine manure, and digested anaerobic sludge

This study explores the influence of wastewater feedstock composition on hydrothermal liquefaction (HTL) biocrude oil properties and physico-chemical characteristics. Spirulina algae, swine manure, and digested sludge were converted under HTL conditions (300°C, 10-12 MPa, and 30 min reaction time). Biocrude yields ranged from 9.4% (digested sludge) to 32.6% (Spirulina). Although similar higher heating values (32.0-34.7 MJ/kg) were estimated for all product oils, more detailed characterization revealed significant differences in biocrude chemistry. Feedstock composition influenced the individual compounds identified as well as the biocrude functional group chemistry. Molecular weights tracked with obdurate carbohydrate content and followed the order of Spirulina<swine manure<digested sludge. A similar trend was observed in boiling point distributions and the long branched aliphatic contents. These findings show the importance of HTL feedstock composition and highlight the need for better understanding of biocrude chemistries when considering bio-oil uses and upgrading requirements.

Lignin valorization through integrated biological funneling and chemical catalysis.

Significance For nearly a century, processes have been used to convert biomass-derived carbohydrates, such as glucose, into fuels and chemicals. However, plant cell walls also contain an aromatic polymer, lignin, that has not been cost-effectively converted into fuels or commodity chemicals. With the intensive development of lignocellulosic biorefineries around the world to produce fuels and chemicals from biomass-derived carbohydrates, the amount of waste lignin will dramatically increase, warranting new lignin upgrading strategies. In nature, some microorganisms have evolved pathways to catabolize lignin-derived aromatics. Our work demonstrates that the utilization of these natural aromatic catabolic pathways may enable new routes to overcome the lignin utilization barrier that, in turn, may enable a broader slate of molecules derived from lignocellulosic biomass. Lignin is an energy-dense, heterogeneous polymer comprised of phenylpropanoid monomers used by plants for structure, water transport, and defense, and it is the second most abundant biopolymer on Earth after cellulose. In production of fuels and chemicals from biomass, lignin is typically underused as a feedstock and burned for process heat because its inherent heterogeneity and recalcitrance make it difficult to selectively valorize. In nature, however, some organisms have evolved metabolic pathways that enable the utilization of lignin-derived aromatic molecules as carbon sources. Aromatic catabolism typically occurs via upper pathways that act as a “biological funnel” to convert heterogeneous substrates to central intermediates, such as protocatechuate or catechol. These intermediates undergo ring cleavage and are further converted via the β-ketoadipate pathway to central carbon metabolism. Here, we use a natural aromatic-catabolizing organism, Pseudomonas putida KT2440, to demonstrate that these aromatic metabolic pathways can be used to convert both aromatic model compounds and heterogeneous, lignin-enriched streams derived from pilot-scale biomass pretreatment into medium chain-length polyhydroxyalkanoates (mcl-PHAs). mcl-PHAs were then isolated from the cells and demonstrated to be similar in physicochemical properties to conventional carbohydrate-derived mcl-PHAs, which have applications as bioplastics. In a further demonstration of their utility, mcl-PHAs were catalytically converted to both chemical precursors and fuel-range hydrocarbons. Overall, this work demonstrates that the use of aromatic catabolic pathways enables an approach to valorize lignin by overcoming its inherent heterogeneity to produce fuels, chemicals, and materials.

Thermochemical conversion of raw and defatted algal biomass via hydrothermal liquefaction and slow pyrolysis

Thermochemical conversion is a promising route for recovering energy from algal biomass. Two thermochemical processes, hydrothermal liquefaction (HTL: 300 °C and 10-12 MPa) and slow pyrolysis (heated to 450 °C at a rate of 50 °C/min), were used to produce bio-oils from Scenedesmus (raw and defatted) and Spirulina biomass that were compared against Illinois shale oil. Although both thermochemical conversion routes produced energy dense bio-oil (35-37 MJ/kg) that approached shale oil (41 MJ/kg), bio-oil yields (24-45%) and physico-chemical characteristics were highly influenced by conversion route and feedstock selection. Sharp differences were observed in the mean bio-oil molecular weight (pyrolysis 280-360 Da; HTL 700-1330 Da) and the percentage of low boiling compounds (bp<400 °C) (pyrolysis 62-66%; HTL 45-54%). Analysis of the energy consumption ratio (ECR) also revealed that for wet algal biomass (80% moisture content), HTL is more favorable (ECR 0.44-0.63) than pyrolysis (ECR 0.92-1.24) due to required water volatilization in the latter technique.

Adipic acid production from lignin.

Lignin is an alkyl-aromatic polymer present in plant cell walls for defense, structure, and water transport. Despite exhibiting a high-energy content, lignin is typically slated for combustion in modern biorefineries due to its inherent heterogeneity and recalcitrance, whereas cellulose and hemicellulose are converted to renewable fuels and chemicals. However, it is critical for the viability of third-generation biorefineries to valorize lignin alongside polysaccharides. To that end, we employ metabolic engineering, separations, and catalysis to convert lignin-derived species into cis,cis-muconic acid, for subsequent hydrogenation to adipic acid, the latter being the most widely produced dicarboxylic acid. First, Pseudomonas putida KT2440 was metabolically engineered to funnel lignin-derived aromatics to cis,cis-muconate, which is an atom-efficient biochemical transformation. This engineered strain was employed in fed-batch biological cultivation to demonstrate a cis,cis-muconate titer of 13.5 g L−1 in 78.5 h from a model lignin-derived compound. cis,cis-Muconic acid was recovered in high purity (>97%) and yield (74%) by activated carbon treatment and crystallization (5 °C, pH 2). Pd/C was identified as a highly active catalyst for cis,cis-muconic acid hydrogenation to adipic acid with high conversion (>97%) and selectivity (>97%). Under surface reaction controlling conditions (24 °C, 24 bar, ethanol solvent), purified cis,cis-muconic acid exhibits a turnover frequency of 23–30 s−1 over Pd/C, with an apparent activation energy of 70 kJ mol−1. Lastly, cis,cis-muconate was produced with engineered P. putida grown on a biomass-derived, lignin-enriched stream, demonstrating an integrated strategy towards lignin valorization to an important commodity chemical.

Critical review of Pd-based catalytic treatment of priority contaminants in water

Catalytic reduction of water contaminants using palladium (Pd)-based catalysts and hydrogen gas as a reductant has been extensively studied at the bench-scale, but due to technical challenges it has only been limitedly applied at the field-scale. To motivate research that can overcome these technical challenges, this review critically analyzes the published research in the area of Pd-based catalytic reduction of priority drinking water contaminants (i.e., halogenated organics, oxyanions, and nitrosamines), and identifies key research areas that should be addressed. Specifically, the review summarizes the state of knowledge related to (1) proposed reaction pathways for important classes of contaminants, (2) rates of contaminant reduction with different catalyst formulations, (3) long-term sustainability of catalyst activity with respect to natural water foulants and regeneration strategies, and (4) technology applications. Critical barriers hindering implementation of the technology are related to catalyst activity (for some contaminants), stability, fouling, and regeneration. New developments overcoming these limitations will be needed for more extensive field-scale application of this technology.

Oxidation Kinetics of Antibiotics during Water Treatment with Potassium Permanganate

The ubiquitous occurrence of antibiotics in aquatic environments raises concerns about potential adverse effects on aquatic ecology and human health, including the promotion of increased antibiotic resistance. This study examined the oxidation of three widely detected antibiotics (ciprofloxacin, lincomycin, and trimethoprim) by potassium permanganate [KMnO(4); Mn(VII)]. Reaction kinetics were described by second-order rate laws, with apparent second-order rate constants (k(2)) at pH 7 and 25 degrees C in the order of 0.61 +/- 0.02 M(-1) s(-1) (ciprofloxacin) < 1.6 +/- 0.1 M(-1) s(-1) (trimethoprim) < 3.6 +/- 0.1 M(-1) s(-1) (lincomycin). Arrhenius temperature dependence was observed with apparent activation energies (E(a)) ranging from 49 kJ mol(-1) (trimethoprim) to 68 kJ mol(-1) (lincomycin). Rates of lincomycin and trimethoprim oxidation exhibited marked pH dependences, whereas pH had only a small effect on rates of ciprofloxacin oxidation. The effects of pH were quantitatively described by considering parallel reactions between KMnO(4) and individual acid-base species of the target antibiotics. Predictions from a kinetic model that included temperature, KMnO(4) dosage, pH, and source water oxidant demand as input parameters agreed reasonably well with measurements of trimethoprim and lincomycin oxidation in six drinking water utility sources. Although Mn(VII) reactivity with the antibiotics was lower than that reported for ozone and free chlorine, its high selectivity and stability suggests a promising oxidant for treating sensitive micropollutants in organic-rich matrices (e.g., wastewater).

Oxidation of Antibiotics during Water Treatment with Potassium Permanganate: Reaction Pathways and Deactivation

Recent work demonstrates that three widely administered antibiotics (ciprofloxacin, lincomycin, and trimethoprim) are oxidized by potassium permanganate [KMnO(4), Mn(VII)] under conditions relevant to water treatment operations. However, tests show that little to no mineralization occurs during reactions with Mn(VII), so studies were undertaken to characterize the reaction products and pathways and to assess the effects of Mn(VII)-mediated transformations on the antibacterial activity of solutions. Several oxidation products were identified for each antibiotic by liquid chromatography-tandem mass spectrometry (LC-MS/MS). For ciprofloxacin, 12 products were identified, consistent with oxidation of the tertiary aromatic and secondary aliphatic amine groups on the piperazine ring and the cyclopropyl group. For lincomycin, seven products were identified that indicate structural changes to the pyrrolidine ring and thioether group. For trimethoprim, seven products were identified, consistent with Mn(VII) reaction at C═C double bonds on the pyrimidine ring and the bridging methylene group. Oxidation pathways are proposed based on the identified products. Bacterial growth inhibition bioassays (E. coli DH5α) show that the mixture of products resulting from Mn(VII) reactions with the antibiotics collectively retain negligible antibacterial potency in comparison to the parent antibiotics. These results suggest that permanganate can be an effective reagent for eliminating the pharmaceutical activity of selected micropollutants during drinking water treatment.

Direct Photolysis of Human Metabolites of the Antibiotic Sulfamethoxazole: Evidence for Abiotic Back-Transformation

The presence of potentially persistent and bioactive human metabolites in surface waters gives rise to concern; yet little is known to date about the environmental fate of these compounds. This work investigates the direct photolysis of human metabolites of the antibiotic sulfamethoxazole (SMX). In particular, we determined photolysis kinetics and products, as well as their concentrations in lake water. SMX, N-acetyl sulfamethoxazole, sulfamethoxazole β-D-glucuronide, 4-nitroso sulfamethoxazole, and 4-nitro sulfamethoxazole were irradiated under various light sources and pH conditions. All investigated metabolites, except sulfamethoxazole β-D-glucuronide were found to be more photostable than SMX under environmentally relevant conditions. Between two and nine confirmed photoproducts were identified for SMX-metabolites through ultraperformance liquid chromatography/high-resolution mass spectrometry. Interestingly, photolytic back-transformation to SMX was observed for 4-nitroso-SMX, indicating that this metabolite may serve as an environmental source of SMX. Moreover, two human metabolites along with SMX were regularly detected in Lake Geneva. The knowledge that some metabolites retain biological activity, combined with their presence in the environment and their potential to retransform to the parent compound, underlines the importance of including human metabolites when assessing the effects of pharmaceuticals in the environment.

Prediction of microalgae hydrothermal liquefaction products from feedstock biochemical composition

Hydrothermal liquefaction (HTL) uses water under elevated temperatures and pressures (200–350 °C, 5–20 MPa) to convert biomass into liquid “biocrude” oil. Despite extensive reports on factors influencing microalgae cell composition during cultivation and separate reports on HTL products linked to cell composition, the field still lacks a quantitative model to predict HTL conversion product yield and qualities from feedstock biochemical composition; the tailoring of microalgae feedstock for downstream conversion is a unique and critical aspect of microalgae biofuels that must be leveraged upon for optimization of the whole process. This study developed predictive relationships for HTL biocrude yield and other conversion product characteristics based on HTL of Nannochloropsis oculata batches harvested with a wide range of compositions (23–59% dw lipids, 58–17% dw proteins, 12–22% dw carbohydrates) and a defatted batch (0% dw lipids, 75% dw proteins, 19% dw carbohydrates). HTL biocrude yield (33–68% dw) and carbon distribution (49–83%) increased in proportion to the fatty acid (FA) content. A component additivity model (predicting biocrude yield from lipid, protein, and carbohydrates) was more accurate predicting literature yields for diverse microalgae species than previous additivity models derived from model compounds. FA profiling of the biocrude product showed strong links to the initial feedstock FA profile of the lipid component, demonstrating that HTL acts as a water-based extraction process for FAs; the remainder non-FA structural components could be represented using the defatted batch. These findings were used to introduce a new FA-based model that predicts biocrude oil yields along with other critical parameters, and is capable of adjusting for the wide variations in HTL methodology and microalgae species through the defatted batch. The FA model was linked to an upstream cultivation model (Phototrophic Process Model), providing for the first time an integrated modeling framework to overcome a critical barrier to microalgae-derived HTL biofuels and enable predictive analysis of the overall microalgal-to-biofuel process.

Microbially Mediated Abiotic Transformation of the Antimicrobial Agent Sulfamethoxazole under Iron-Reducing Soil Conditions

Large quantities of antimicrobial agents used in livestock production are released to soils by land application of manure, but only limited information is available on mechanisms that contribute to antimicrobial fate in soils under variable biogeochemical conditions. Dissipation of the sulfonamide antimicrobial sulfamethoxazole was examined in soil microcosms incubated under different terminal electron-accepting conditions (aerobic, nitrate-reducing, Fe(III)-reducing, and sulfate-reducing). Somewhat unexpectedly, sulfamethoxazole dissipation was fastest under Fe(III)-reducing conditions, with concentrations decreasing by >95% within 1 day. The rapid transformation was attributed to abiotic reactions between sulfamethoxazole and Fe(II) generated by microbial reduction of Fe(III) soil minerals. Separate experiments demonstrated that sulfamethoxazole was abiotically transformed in Fe(II)-amended aqueous suspensions of goethite (α-FeOOH((s))), and observed rate constants varied with the extent of Fe(II) sorption to goethite. Sulfamethoxazole transformation is initiated by a 1-electron reductive cleavage of the N-O bond in the isoxazole ring substituent, and observed products are consistent with Fe(II)-mediated reduction and isomerization processes. These findings reveal potentially important, but previously unrecognized, pathways that may contribute to the fate of sulfamethoxazole and related chemicals in reducing soil environments.