Ullrich Steiner

Formation of Nanopatterned Polymer Blends in Photovoltaic Devices

In this paper, we demonstrate a double nanoimprinting process that allows the formation of nanostructured polymer heterojunctions of composition and morphology that can be selected independently. We fabricated photovoltaic (PV) devices with extremely high densities (10(14)/mm(2)) of interpenetrating nanoscale columnar features in the active polymer blend layer. The smallest feature sizes are as small as 25 nm on a 50 nm pitch, which results in a spacing of heterojunctions at or below the exciton diffusion length. Photovoltaic devices based on double-imprinted poly((9,9-dioctylfluorene)-2,7-diyl-alt-[4,7-bis(3-hexylthien-5-yl)-2,1,3-benzothiadiazole]-2,2-diyl) (F8TBT)/ poly(3-hexylthiophene) (P3HT) films are among the best polymer-polymer blend devices reported to date with a power conversion efficiency (PCE, eta(e)) of 1.9%.

Block Copolymer Morphologies in Dye-Sensitized Solar Cells: Probing the Photovoltaic Structure-Function Relation

We integrate mesostructured titania arrays into dye-sensitized solar cells by replicating ordered, oriented one-dimensional (1D) columnar and three-dimensional (3D) bicontinuous gyroid block copolymer phases. The solar cell performance, charge transport, and recombination are investigated. We observe faster charge transport in 1D wires than through 3D gyroid arrays. However, owing to their structural instability, the surface area of the wire arrays is low, inhibiting the solar cell performance. The gyroid morphology, on the other hand, outperforms the current state-of-the-art mesoporous nanoparticle films.

Friction ridges in cockroach climbing pads: anisotropy of shear stress measured on transparent, microstructured substrates

The contact of adhesive structures to rough surfaces has been difficult to investigate as rough surfaces are usually irregular and opaque. Here we use transparent, microstructured surfaces to investigate the performance of tarsal euplantulae in cockroaches (Nauphoeta cinerea). These pads are mainly used for generating pushing forces away from the body. Despite this biological function, shear stress (force per unit area) measurements in immobilized pads showed no significant difference between pushing and pulling on smooth surfaces and on 1-μm high microstructured substrates, where pads made full contact. In contrast, on 4-μm high microstructured substrates, where pads made contact only to the top of the microstructures, shear stress was maximal during a push. This specific direction dependence is explained by the interlocking of the microstructures with nanometre-sized “friction ridges” on the euplantulae. Scanning electron microscopy and atomic force microscopy revealed that these ridges are anisotropic, with steep slopes facing distally and shallow slopes proximally. The absence of a significant direction dependence on smooth and 1-μm high microstructured surfaces suggests the effect of interlocking is masked by the stronger influence of adhesion on friction, which acts equally in both directions. Our findings show that cockroach euplantulae generate friction using both interlocking and adhesion.

Soft-Etch Mesoporous Hole-Conducting Block Copolymer Templates

We present a mesoporous hole-conducting polymer film resulting from spontaneous block copolymer self-assembly based on a simple spin-coating protocol. A diblock copolymer consisting of a triphenylamine side group polymer and a poly(d,l-lactide) block (PSTPA-b-PLA) is shown to microphase separate to form ordered 13 nm cylindrical PLA microdomains embedded in the semiconducting PSTPA matrix. Partially ordered and film-spanning PLA domains could be identified in films immediately after spin coating from toluene solutions on conducting substrates. Selective mild etching of the minority PLA domains (in weak aqueous base) leads to a mesoporous hole-conducting polymer matrix. The pore structure is replicated electrochemically in platinum, demonstrating the viability of this approach to producing nano-organized heterojunction structures in thin films.

Research Data Supporting "Gyroid Optical Metamaterials: Calculating the Effective Permittivity of Multidomain Samples"

Data Supporting Publication Gyroid Optical Metamaterials: Calculating the Effective Permittivity of Multidomain Samples