V. K. Gusev

High kinetic energy plasma jet generation and its injection into the Globus-M spherical tokamak

Progress in the theoretical and experimental development of the plasma jet source and injection of hydrogen plasma and neutral gas jets into the Globus-M spherical tokamak is discussed. An experimental test bed is described for investigation of intense plasma jets that are generated by a double-stage plasma gun consisting of an intense source for neutral gas production and a conventional pulsed coaxial accelerator. A procedure for optimizing the accelerator parameters so as to achieve the maximum possible flow velocity with a limited discharge current and a reasonable length of the coaxial electrodes is presented. The calculations are compared with experiment. Plasma jet parameters, among them pressure distribution across the jet, flow velocity, plasma density, etc, were measured. Plasma jets with densities of up to 1022 m−3, total numbers of accelerated particles (1–5) × 1019, and flow velocities of 50–100 km s−1 were successfully injected into the plasma column of the Globus-M tokamak. Interferometric and Thomson scattering measurements confirmed deep jet penetration and a fast density rise (<0.5 ms) at all spatial points up to a radius r≈ 0.3a. The plasma particle inventory increase by ~50% (from 0.65 × 1019 to 1 × 1019) did not result in plasma degradation.

Geodesic acoustic mode observations in the Globus-M spherical tokamak

The results of geodesic acoustic mode (GAM) studies in the spherical torus Globus-M via Doppler reflectometry are presented. The intermittent character of the GAM evolution is similar to the limit-cycle oscillation behavior of zonal flows. The evident correlation between the GAM rotational velocity and both Dα emission and plasma density oscillations is exhibited and discussed. The obtained experimental results are compared with those from tokamaks with large aspect ratios.

Overview of results obtained at the Globus-M spherical tokamak

Experiments and simulations to achieve high values of plasma parameters at the Globus-M spherical tokamak (ST) at moderate absolute auxiliary heating power (up to 0.8 MW) and high specific heating power (up to 2–3 MW m−3) are described. Important distinguishing features are the low edge safety factor range, which is unusual for STs, 2.7 < q < 5 and small plasma–outer wall space (3–5 cm). High ion heating efficiency with neutral beam injection (NBI) was demonstrated. Results of numerical simulation of fast ion trajectories are described and fast ion generation during the NBI and ion cyclotron resonance heating is discussed. Investigations on their confinement and slowing down are also presented. Reasons for achievement of high IC heating efficiency are outlined. Reliable H-mode regime achievement is described. Transport ASTRA modelling demonstrated that during NB heated H-mode ion heat diffusivity remains neoclassical and the particle diffusion coefficient inside transport barrier decreases significantly. Analysis was performed of divertor tile and special probe surfaces after irradiation by plasma during a large number of shots (3000–10 000 shots). Mixed layer composition is measured and deuterium retention in different tokamak first wall areas is estimated. Plasma jet injection experiments with upgraded plasma jet are described. Jet penetration to the plasma centre with immediate increase of density and temperature drop is proved and analogy with pellet injection is outlined.

Review of Globus-M spherical tokamak results

The first experiments on noninductive current drive (CD) using lower hybrid waves in a spherical tokamak are described. Waves at 2.45 GHz were launched by a 10 waveguide grill with 120° phase shift between neighbouring waveguides. The experimental results for a novel poloidal slowing-down scheme are described. The CD efficiency is found to be somewhat larger than that predicted theoretically whilst at the same time being somewhat less than that for standard tokamak lower hybrid CD. Geodesic acoustic modes (GAM) have been discovered in Globus-M. GAMs are localized 2–3 cm inside the separatrix. The GAM frequency agrees with theory. The mode structures of plasma density and magnetic field oscillation at the GAM frequency have been studied. Fast particle confinement during neutral beam injection has been investigated and numerically simulated. Alfven instabilities excited by fast particles were detected by a toroidal Mirnov probe array. Their excitation conditions are discussed and the dynamics of fast ion losses induced by Alfven eigenmodes is presented. Preliminary experiments on the isotopic effect influence on global confinement in the ohmic heating (OH) regime are described. Scrape-off layer (SOL) parameters were measured and compared with results from self-consistent integrated transport modelling. Results showed that SOL width scales inversely proportional to plasma current. The behaviour of an a priori damaged tungsten divertor plate mock-up exposed to plasma flows was investigated. Preliminary conclusions are that the initial damage gives rise to a loose layer formation with low thermal conductivity right beneath the surface. Finally, engineering design issues of the next step—Globus-M2 (1 T, 500 kA) and the status of component manufacture are described.

Density limits and control in the Globus-M spherical tokamak

The results of the experimental campaign on Globus-M (R = 0.36 m, a = 24 m) devoted to investigating density limits and density control are reported. The experiments were performed at Btor = 0.4 T, Ip = 0.18–0.25 MA, q95 = 3.5–5 and plasma vertical elongation, κ ~ 1.5–1.7. The density limits achieved with the gas puffing method of density control in the previous periods in ohmic heating (OH) regime are discussed. The progress made in OH scenario optimization helped the density to approach the Greenwald limit. Co-current neutral beam of deuterium with the power in the range of 0.45–0.6 MW at the beam energy of 28–29 keV was injected into deuterium target plasma at the early stage of the discharge, which allowed the density to overcome the Greenwald limit. Line averaged densities in excess of 1.5 × 1020 m−3 were achieved, during the external gas puff. An ion temperature increase, measured by NPA was accompanied by a definite increase in the electron energy content, registered by Thomson scattering. Injection of a pure, highly ionized hydrogen plasma jet with a density up to 1022 m−3, total number of accelerated particles (1–5) × 1019 and a flow velocity of ~110 km s−1 was used as another instrument for density control. It increased plasma particle inventory in the Globus-M by ~50% (from 0.65 × 1019 to 1 × 1019) in a single shot without target OH plasma parameter degradation. The injection resulted in a fast density increase with the time much shorter than with gas puff fuelling, which was confirmed by Thomson scattering measurements.

Plasma formation and first OH experiments in the Globus-M tokamak

The article reports the results of experimental campaigns on plasma ohmic heating performed during 1999-2000 on the spherical tokamak Globus-M. Later experimental results with the tokamak fed by thyristor rectifiers are presented in detail. The toroidal magnetic field and plasma pulse duration in these experiments were significantly increased. The method of stray magnetic field compensation is described. The technology of vacuum vessel conditioning, including boronization of the vessel performed at the end of the experiments, is briefly discussed. Specific features of neutral gas column breakdown in spherical tokamaks by applied inductive voltage are outlined. Also discussed is the influence of ECR preionization on the breakdown conditions. Experimental data on plasma column formation and current ramp-up in different regimes of operation with the magnetic flux of the central solenoid limited to ~100 mWb are presented. A significant reduction of the background density after boronization (below 2 × 1018m-3) allows the density to be completely controlled with external gas puffing and makes the influence of the wall negligible. The magnetic flux consumption efficiency is discussed. The results of magnetic equilibrium simulations are presented and compared with experiment. Ramp-up of the plasma current of 0.25 MA for a time interval of about 0.03 s with about 0.02 s flat-top at a toroidal field strength of 0.35 T allows the conclusion that the target design parameters of Globus-M could be achieved in a double swing regime.

Measurement of the plasma jet parameters during material irradiation

A technique is presented for determining the parameters of a high-energy plasma jet during the irradiation of the first wall of a thermonuclear reactor on a plasma gun bench. The plasma density is measured with a Michelson interferometer mounted on a through flange. The plasma velocity is determined by observing the propagation of the ionization front using a K008 streak camera. The plasma composition at the output of the accelerator and near the irradiated target is found with an AvaSpec 3648 panoramic spectrometer. The kinetic energy of the jet is recorded calorimetrically. The action (pressure) of the plasma jet on the target is confirmed with piezoelectric and interferometric methods simultaneously in each radiation event. It is found that the plasma gun bench is able to generate a plasma with an energy flux density similar to that observed in the case of edge-localized modes in a tokamak and makes it possible to carry out experiments aimed at developing protective materials for the international thermonuclear experimental reactor.

Investigation of beam– and wave–plasma interactions in spherical tokamak Globus-M

The experimental and theoretical results obtained in the last two years on the interaction of neutral particle beams and high-frequency waves with a plasma using the spherical tokamak Globus-M are discussed. The experiments on the injection of low-energy proton beam of ~300 eV directed particle energy are performed with a plasma gun that produces a hydrogen plasma jet of density up to 3 × 1022 m−3 and a high velocity up to 250 km s−1. A moderate density rise (up to 30%) is achieved in the central plasma region without plasma disruption. Experiments on high-energy (up to 30 keV) neutral beam injection into the D-plasma are analysed. Modelling results on confinement of fast particles inside the plasma column that follows the neutral beam injection are discussed. The influence of the magnetic field on the fast particle losses is argued. A neutral beam injection regime with primary ion heating is obtained and discussed. The new regime with fast current ramp-up and early neutral beam injection shows electron temperature rise and formation of broad Te profiles until the q = 1 flux surface enters the plasma column. An energetic particle mode in the range of frequencies 5–30 kHz and toroidal Alfven eigenmodes in the range 50–300 kHz are recorded in that regime simultaneously with the Te rise. The energetic particle mode and toroidal Alfven eigenmodes behaviour are discussed. The toroidal Alfven eigenmode spectrum appears in Globus-M as a narrow band corresponding to n = 1. The first experimental results on plasma start-up and noninductive current drive generation are presented. The experiments are carried out with antennae providing mostly poloidal slowing down of waves with a frequency of 920 MHz, which is higher than a lower hybrid one existing under the experimental conditions. The high current drive efficiency is shown to be high (of about 0.25 A W−1), and its mechanism is proposed. Some near future plans of the experiments are also discussed.

On-line plasma shape reconstruction algorithm in tokamaks and its verification in the Globus-M

An on-line plasma shape reconstruction algorithm is necessary to design the plasma position and shape control system in modern tokamaks. An algorithm aimed at solving this problem is proposed. A description of the mathematical procedure is provided and experimental data incorporation is discussed. An example of an application of this algorithm is demonstrated using experimental data from Globus-M discharge #10292.

Influence of a plasma jet on different types of tungsten

The influence of a plasma producing nonstationary thermal loads akin to edge-localized modes in a tokamak on different types of tungsten is investigated. Tungsten is irradiated by a jet of a hydrogen plasma generated in a plasma gun. The plasma density and velocity are on the order of 1022 m−3 and 100–200 km/s, respectively, and the irradiation time is 10 μs. Two plasma flux densities, 0.70 and 0.25 MJ/m2, are used. Structural modifications in irradiated single-crystal and hot-rolled tungsten samples, as well as in V-MP and ITER_D_2EDZJ4 tungsten powders, are examined. It is found that the plasma generates a regular crack network with a period of about 1 mm on the surface of the single-crystal, hot-rolled, and V-MP powder samples, while the surface of the ITER_D_2EDZJ4 powder is more cracking-resistant. The depth of the molten layer equals 1–3 μm, and the extension of intense thermal action is 15–20 μm. The material acquires a distinct regular structure with a typical grain size of less than 1 μm. X-ray diffraction analysis shows that irradiation changes the crystal lattice parameters because of the melting and crystallization of the surface layer. The examination of the V_MP tungsten powder after cyclic irradiation by a plasma with different energy densities shows that high-energy-density irradiation causes the most significant surface damage, whereas low-energy-density irradiation generates defects that are small in size even if the number of cycles is large.