V.V. Shlyaptseva

Radiation sources with planar wire arrays and planar foils for inertial confinement fusion and high energy density physics research

This article reports on the joint success of two independent lines of research, each of them being a multi-year international effort. One of these is the development of innovative sources, such as planar wire arrays (PWAs). PWAs turned out to be a prolific radiator, which act mainly as a resistor, even though the physical mechanism of efficient magnetic energy conversion into radiation still remains unclear. We review the results of our extensive studies of PWAs. We also report the new results of the experimental comparison PWAs with planar foil liners (another promising alternative to wire array loads at multi-mega-ampere generators). Pioneered at UNR, the PWA Z-pinch loads have later been tested at the Sandia National Laboratories (SNL) on the Saturn generator, on GIT-12 machine in Russia, and on the QiangGuang-1 generator in China, always successfully. Another of these is the drastic improvement in energy efficiency of pulsed-power systems, which started in early 1980s with Zuckers experiments at Nava...

Implosion dynamics in double planar wire array Z pinches

The double planar wire array (DPWA) Z pinch is a highly efficient radiation source with unique implosion dynamics and precursor formations. The inductively divided current successively ablates the wires and injects the material to the interior of the array. Three uniquely imploding DPWA load types were identified and classified according to the critical load parameter: low, intermediate, or high aspect ratio. Radiation pulse shaping was obtained from secondary precursors: off-axis mass carrying high current densities during the implosion phase. Time-gated EUV spectroscopy of off-axis mass accumulations is used to assess a 60 eV electron temperature prior to the implosion phase. These structures are shown to form by a different mechanism than the secondary precursors. High yields, compact size, and shaped radiation pulses merit further consideration of the DPWA as a candidate for inertial confinement fusion research.

Radiation from mixed multi-planar wire arrays

The study of radiation from different wire materials in wire array Z-pinch plasma is a very challenging topic because it is almost impossible to separate different plasmas at the stagnation. A new approach is suggested based on planar wire array (PWA) loads to assess this problem. Multi-planar wire arrays are implemented that consist of few planes, each with the same number of wires and masses but from different wire materials, arranged in parallel rows. In particular, the experimental results obtained with triple PWAs (TPWAs) on the UNR Zebra generator are analyzed with Wire Ablation Dynamics Model, non-local thermodynamic equilibrium kinetic model, and 2D radiation magneto-hydrodynamic to illustrate this new approach. In TPWAs, two wire planes were from mid-atomic-number wire material and another plane was from alloyed Al, placed either in the middle or at the edge of the TPWA. Spatial and temporal properties of K-shell Al and L-shell Cu radiations were analyzed and compared from these two configurations of TPWAs. Advantages of the new approach are demonstrated and future work is discussed.

Anisotropy of radiation emitted from planar wire arrays

The planar wire array (PWA) is a promising load for new multi-source inertial confinement fusion (ICF) hohlraums [B. Jones et al., Phys. Rev. Lett. 104, 125001 (2010)]. The hohlraum radiation symmetry is an important issue for ICF. It was found that extreme ultraviolet and sub-keV photon emission from PWAs may have considerable anisotropy in the load azimuthal plane. This experimental result is obtained on the UNR 1–1.7 MA Zebra generator. The time-dependent anisotropy effect is detected. This feature is studied in 2D numerical simulations and can be explained by initial anisotropy of implosion of those non-cylindrical loads radiating essentially as surface sources in sub-keV quanta and also by radiation absorption in cold magnetized plasma tails forming in the direction of magnetic compression.

Ablation dominated implosion dynamics of aluminum and stainless steel nested cylindrical wire arrays

The results of experiments with combined aluminum (Al) and stainless steel (SS) alloy 304, nested wire arrays from the 1 MA COBRA generator at Cornell University are presented. The loads studied consisted of a 6 mm diameter inner array and a 13 mm diameter outer array with a different material in each array: SS or aluminum. Al implodes before SS in all loads studied, even when Al was on the inner array. The new wire ablation dynamic model and spectroscopic modeling are used to interpret these data. The observed implosion dynamics are likely a result of the higher ablation rate of Al. These initial results suggest that combining wire materials with different ablation rates in wire array loads could be developed into a useful technique for x-ray pulse shaping and radiation yield optimization.

Analysis of X-ray iron and nickel radiation and jets from planar wire arrays and X-pinches

University-scale Z-pinch devices are able to produce plasmas with a broad range of sizes, temperatures, densities, their gradients, and opacity properties. Radiative properties of such plasmas depend on material, mass, and configuration of the wire array loads. Experiments with two different types of loads, double planar wire arrays (DPWA) and X-pinches, performed on the 1 MA Zebra generator at UNR are analyzed. X-pinches are made from Stainless Steel (69% Fe, 20% Cr, and 9% Ni) wires. Combined DPWAs consist of one plane from SS wires and another plane from Alumel (95% Ni, 2% Al, 2% Si) wires. The main focus of this work is on the analysis of plasma jets at the early phase of plasma formation and the K-and L-shell radiation generation at the implosion and stagnation phases in experiments with the two aforementioned wire loads. The relevant theoretical tools that guide the data analysis include non-LTE collisional-radiative and wire ablation dynamics models. The astrophysical relevance of the plasma jets as well as of spectroscopic and imaging studies are demonstrated.

Radiation from Ag high energy density Z-pinch plasmas and applications to lasing

Silver (Ag) wire arrays were recently introduced as efficient x-ray radiators and have been shown to create L-shell plasmas that have the highest electron temperature (>1.8 keV) observed on the Zebra generator so far and upwards of 30 kJ of energy output. In this paper, results of single planar wire arrays and double planar wire arrays of Ag and mixed Ag and Al that were tested on the UNR Zebra generator are presented and compared. To further understand how L-shell Ag plasma evolves in time, a time-gated x-ray spectrometer was designed and fielded, which has a spectral range of approximately 3.5–5.0 A. With this, L-shell Ag as well as cold Lα and Lβ Ag lines was captured and analyzed along with photoconducting diode (PCD) signals (>0.8 keV). Along with PCD signals, other signals, such as filtered XRD (>0.2 keV) and Si-diodes (SiD) (>9 keV), are analyzed covering a broad range of energies from a few eV to greater than 53 keV. The observation and analysis of cold Lα and Lβ lines show possible correlations w...

Scaling of Radiation Parameters of Planar and Compact Cylindrical Wire Arrays at the 1 MA Zebra Generator

Analysis is presented on scaling of radiated x‐ray power, energy and implosion timing of single planar wire arrays (SPWA), double planar wire array (DPWA), and compact cylindrical wire array (CCWA) loads (diameter is 3 and 6 mm) of Mo and W with respect to current peak (0.8–1.4 MA), mass and array dimensions at 100 ns current pulse. Such scaling investigations are important for understanding the potential of these loads as an ICF radiation source7. These data are used to identify promising directions to pursue with regard to highest x‐ray output, smallest load size, and most consistent shot‐to‐shot performance. It is shown that W SPWA and DPWA total energy yield and peak power increased near‐quadratically with current. DPWA scans of inter‐planar gaps from 1.5 mm to 9 mm show an output maximum at 1.5 mm with decreasing output for 6 mm and 9 mm. A DPWA width scan shows that radiation yields decrease slowly as the width is decreased, which may allow for more compact loads without significant sacrifice to the...

Producing Kiloelectronvolt L-Shell Plasmas on Zebra at UNR

Experiments with various wire loads from mid-atomic-number wires, which were performed on the university-scale 1-MA Zebra generator at the University of Nevada, Reno, during the last few years, are analyzed to assess the highest electron temperature reached. In particular, the results from experiments with planar wire arrays (PWAs) were considered. Load materials from mid-atomic-number such as stainless steel, Alumel, Cu, brass, Mo, and up to Ag were used to generate L-shell plasmas and to study plasma parameters. Though the full diagnostic set was utilized, the main focus was on X-ray spectroscopic data and on the non-local thermodynamic equilibrium kinetic modeling. As a result, the scaling of the maximum Te with the load material atomic number is presented for the first time in the range from Fe to Ag for L-shell plasmas from PWAs. The highest values of the electron temperature in L-shell plasmas, which are estimated from the modeling, were from both Ag PWAs and X-pinches. This work is important for the development of efficient X-ray radiators on university-scale Z-pinch generators.

X-ray pulse shaping in experiments with planar wire arrays at the 1.6 MA Zebra generator

The shaping of the x-ray radiation pulse is very important in both radiation physics research and Inertial Confinement Fusion studies. The novel planar wire array (PWA) was found to be the effective radiator tested at the university-scale 1.6 MA, 100 ns Zebra generator. The single PWA consists of a single row of wires that are parallel to each other, while the double planar wire array (DPWA) and triple planar wire array (TPWA) include two or three parallel plane wire rows, respectively. All multi-planar geometries resulted in a cascade-type array implosion with a complicated multi-step precursor formation before plasma stagnation. The PWAs (without additional core foam target) feature a dynamic precursor evolution that is a powerful tool for x-ray pulse shaping. The shape and timing of the x-ray pulse from different PWAs were theoretically predicted and experimentally analyzed for a variety of planar wire arrays.