Victoria Flexer

High Acetic Acid Production Rate Obtained by Microbial Electrosynthesis from Carbon Dioxide

High product specificity and production rate are regarded as key success parameters for large-scale applicability of a (bio)chemical reaction technology. Here, we report a significant performance enhancement in acetate formation from CO2, reaching comparable productivity levels as in industrial fermentation processes (volumetric production rate and product yield). A biocathode current density of -102 ± 1 A m(-2) and an acetic acid production rate of 685 ± 30 (g m(-2) day(-1)) have been achieved in this study. High recoveries of 94 ± 2% of the CO2 supplied as the sole carbon source and 100 ± 4% of electrons into the final product (acetic acid) were achieved after development of a mature biofilm, reaching an elevated product titer of up to 11 g L(-1). This high product specificity is remarkable for mixed microbial cultures, which would make the product downstream processing easier and the technology more attractive. This performance enhancement was enabled through the combination of a well-acclimatized and enriched microbial culture (very fast start-up after culture transfer), coupled with the use of a newly synthesized electrode material, EPD-3D. The throwing power of the electrophoretic deposition technique, a method suitable for large-scale production, was harnessed to form multiwalled carbon nanotube coatings onto reticulated vitreous carbon to generate a hierarchical porous structure.

Bringing High-Rate, CO2-Based Microbial Electrosynthesis Closer to Practical Implementation through Improved Electrode Design and Operating Conditions.

The enhancement of microbial electrosynthesis (MES) of acetate from CO2 to performance levels that could potentially support practical implementations of the technology must go through the optimization of key design and operating conditions. We report that higher proton availability drastically increases the acetate production rate, with pH 5.2 found to be optimal, which will likely suppress methanogenic activity without inhibitor addition. Applied cathode potential as low as -1.1 V versus SHE still achieved 99% of electron recovery in the form of acetate at a current density of around -200 A m(-2). These current densities are leading to an exceptional acetate production rate of up to 1330 g m(-2) day(-1) at pH 6.7. Using highly open macroporous reticulated vitreous carbon electrodes with macropore sizes of about 0.6 mm in diameter was found to be optimal for achieving a good balance between total surface area available for biofilm formation and effective mass transfer between the bulk liquid and the electrode and biofilm surface. Furthermore, we also successfully demonstrated the use of a synthetic biogas mixture as carbon dioxide source, yielding similarly high MES performance as pure CO2. This would allow this process to be used effectively for both biogas quality improvement and conversion of the available CO2 to acetate.

Wired pyrroloquinoline quinone soluble glucose dehydrogenase enzyme electrodes operating at unprecedented low redox potential.

We report unprecedented high current densities for the enzymatic oxidation of glucose already at 0 V versus Ag/AgCl. The modified electrodes were made by assembling pyrroloquinoline quinone (PQQ)-soluble glucose dehydrogenase (PQQ-sGDH) from Acinetobacter calcoaceticus with osmium-based redox polymers and a cross-linker. Both redox mediators are made of a poly(4-vinylpyridine) (PVP) polymer with Os complexes tethered to the polymer backbone via long C chains, giving the Os complexes flexibility and mobility inside the redox hydrogels. Current densities larger than 1 mA cm(-2) were measured already below 0 V with a plateau value of 4.4 mA cm(-2). Similar hydrogel electrodes comprising the same redox polymers and glucose oxidase (GOx) showed less than half the current densities of the PQQ-sGDH electrodes. The current versus potential curve dependence showed a sigmoidal shape characteristic of mediated enzyme catalysis but with a current increase versus potential less sharp than expected. Surprisingly, the midwave redox potential was positively shifted with respect to the potential of the redox mediator.

Removal of the X-ray Contrast Media Diatrizoate by Electrochemical Reduction and Oxidation

Due to their resistance to biological wastewater treatment, iodinated X-ray contrast media (ICM) have been detected in municipal wastewater effluents at relatively high concentrations (i.e., up to 100 μg L(-1)), with hospitals serving as their main source. To provide a new approach for reducing the concentrations of ICMs in wastewater, electrochemical reduction at three-dimensional graphite felt and graphite felt doped with palladium nanoparticles was examined as a means for deiodination of the common ICM diatrizoate. The presence of palladium nanoparticles significantly enhanced the removal of diatrizoate and enabled its complete deiodination to 3,5-diacetamidobenzoic acid. When the system was employed in the treatment of hospital wastewater, diatrizoate was reduced, but the extent of electrochemical reduction decreased as a result of competing reactions with solutes in the matrix. Following electrochemical reduction of diatrizoate to 3,5-diacetamidobenzoic acid, electrochemical oxidation with boron-doped diamond (BDD) anodes was employed. 3,5-Diacetamidobenzoic acid disappeared from solution at a rate that was similar to that of diatrizoate, but it was more readily mineralized than the parent compound. When electrochemical reduction and oxidation were coupled in a three-compartment reactor operated in a continuous mode, complete deiodination of diatrizoate was achieved at an applied cathode potential of -1.7 V vs SHE, with the released iodide ions electrodialyzed in a central compartment with 80% efficiency. The resulting BDD anode potential (i.e., +3.4-3.5 V vs SHE) enabled efficient oxidation of the products of the reductive step. The presence of other anions (e.g., chloride) was likely responsible for a decrease in I(-) separation efficiency when hospital wastewater was treated. Reductive deiodination combined with oxidative degradation provides benefits over oxidative treatment methods because it does not produce stable iodinated intermediates. Nevertheless, the process must be further optimized for the conditions encountered in hospital wastewater to improve the separation efficiency of halide ions prior to the electrooxidation step.

Assessment of copper corrosion from frameless copper IUDs after long-term in utero residence

OBJECTIVE To assess the site-specific corrosive behavior of the frameless intrauterine device (IUD) following long-term exposure to the uterine environment. STUDY DESIGN A qualitative and morphological study using X-ray diffraction (XRD) and scanning electron microscopy (SEM). RESULTS Three GyneFix® IUDs that were in site up to 150 months were examined. In utero corroded copper sleeves were divided into 10 different groups based on their shape (U or O), orientation (inside or outside) and in utero residence time. XRD indicated the presence of solely cuprite (Cu2O) as corrosion product on both the inside and the outside of the copper sleeves, regardless of their shape. These results were confirmed by backscattered electron micrographs recorded on the inside, the outside and the cross-section of the IUD sleeve. SEM results suggest that shape and orientation slightly affect the corrosion rate. CONCLUSION The apparent copper loss from both sides of GyneFix copper tubes proves that both sides are a potential copper source and therefore justifies the design of GyneFix IUD. This could be beneficial for women as the IUD could be reduced in size and therefore better tolerated. The impact on bleeding could also be minimized. IMPLICATION STATEMENT Release of copper ions from both sides of the copper tubes of the frameless GyneFix® IUD allows the IUD to be reduced in size, contributing to better toleration. The impact on menstrual bleeding is also minimized by a smaller size of the foreign body.

SR-XRD in situ monitoring of copper-IUD corrosion in simulated uterine fluid using a portable spectroelectrochemical cell

The objective of this work is to study the initial corrosion of copper in the presence of gold when placed in simulated uterine fluid in order to better understand the evolution of active components of copper-IUDs. In order to carry out this study, a portable cell was designed to partially simulate the uterine environment and provide a way of tracking the chemical changes occurring in the samples in situ within a controlled environment over a long period of time using synchrotron spectroelectrochemistry. The dynamically forming crystalline corrosion products are determined in situ for a range of copper-gold surface ratios over the course of a 10-day experiment in the cell. It is concluded that the insoluble deposits forming over this time are not the origin of the anticonception mechanism.