Wei-Chun Hsu

15.7% Efficient 10‐μm‐Thick Crystalline Silicon Solar Cells Using Periodic Nanostructures

Only ten micrometer thick crystalline silicon solar cells deliver a short-circuit current of 34.5 mA cm(-2) and power conversion efficiency of 15.7%. The record performance for a crystalline silicon solar cell of such thinness is enabled by an advanced light-trapping design incorporating a 2D inverted pyramid photonic crystal and a rear dielectric/reflector stack.

Thin-film 'Thermal Well' Emitters and Absorbers for High-Efficiency Thermophotovoltaics.

A new approach is introduced to significantly improve the performance of thermophotovoltaic (TPV) systems using low-dimensional thermal emitters and photovoltaic (PV) cells. By reducing the thickness of both the emitter and the PV cell, strong spectral selectivity in thermal emission and absorption can be achieved by confining photons in trapped waveguide modes inside the thin-films that act as thermal analogs to quantum wells. Simultaneously, photo-excited carriers travel shorter distances across the thin-films reducing bulk recombination losses resulting in a lower saturation current in the PV cell. We predict a TPV efficiency enhancement with near-field coupling between the thermal emitter and the PV cell up to 38.7% using a thin-film germanium (Ge) emitter at 1000 K and an ultra-thin gallium antimonide (GaSb) cell supported by perfect back reflectors separated by 100 nm. Even in the far-field limit, the efficiency is predicted to reach 31.5%, which is over an order of magnitude higher than the Shockley Queisser limit of 1.6% for a bulk GaSb cell and a blackbody emitter at 1000 K. The proposed design approach does not require nanoscale patterning of the emitter and PV cell surfaces, but instead offers a simple low-cost solution to improve the performance of thermophotovoltaic systems.

Enhanced absorption of thin-film photovoltaic cells using an optical cavity

We show via numerical simulations that the absorption and solar energy conversion efficiency of a thin-film photovoltaic (PV) cell can be significantly enhanced by embedding it into an optical cavity. A reflective hemi-ellipsoid with an aperture for sunlight placed over a tilted PV cell reflects unabsorbed photons back to the cell, allowing for multiple opportunities for absorption. Ray tracing simulations predict that with the proposed cavity a textured thin-film silicon cell can exceed the Yablonovitch (Lambertian) limit for absorption across a broad wavelength range, while the performance of the cavity-embedded planar PV cell approaches that of the cell with the surface texturing.

Entropic and Near-Field Improvements of Thermoradiative Cells

A p-n junction maintained at above ambient temperature can work as a heat engine, converting some of the supplied heat into electricity and rejecting entropy by interband emission. Such thermoradiative cells have potential to harvest low-grade heat into electricity. By analyzing the entropy content of different spectral components of thermal radiation, we identify an approach to increase the efficiency of thermoradiative cells via spectrally selecting long-wavelength photons for radiative exchange. Furthermore, we predict that the near-field photon extraction by coupling photons generated from interband electronic transition to phonon polariton modes on the surface of a heat sink can increase the conversion efficiency as well as the power generation density, providing more opportunities to efficiently utilize terrestrial emission for clean energy. An ideal InSb thermoradiative cell can achieve a maximum efficiency and power density up to 20.4% and 327 Wm−2, respectively, between a hot source at 500 K and a cold sink at 300 K. However, sub-bandgap and non-radiative losses will significantly degrade the cell performance.

Limiting efficiencies of solar energy conversion and photo-detection via internal emission of hot electrons and hot holes in gold

We evaluate the limiting efficiency of full and partial solar spectrum harvesting via the process of internal photoemission in Au-semiconductor Schottky junctions. Our results based on the ab initio calculations of the electron density of states (e-DOS) reveal that the limiting efficiency of the full-spectrum Au converter based on hot electron injection is below 4%. This value is even lower than previously established limit based on the parabolic approximation of the Au electron energy bands. However, we predict limiting efficiency exceeding 10% for the hot holes collection through the Schottky junction between Au and p-type semiconductor. Furthermore, we demonstrate that such converters have more potential if used as a part of the hybrid system for harvesting high- and low-energy photons of the solar spectrum.

Direct and quantitative broadband absorptance spectroscopy on small objects using Fourier transform infrared spectrometer and bilayer cantilever probes

A measurement platform is introduced that combines a bilayer cantilever probe with a Fourier transform infrared spectrometer to measure absolute spectral absorptance between wavelengths of 3 μm and 18 μm directly and quantitatively. The enhanced sensitivity provided by the cantilever probe enables the quantitative characterization of micro- and nanometer-sized samples. Validation of the technique is carried out by measuring the absorptance spectrum of a doped silicon thin film with a backside aluminum layer and found to agree well with the theoretical predictions. The presented technique is especially attractive for samples such as individual nanowires or nanoparticles, isolated molecules, powders, and photonic structures.

Direct and Quantitative Photothermal Absorption Spectroscopy of Individual Particulates

Photonic structures can exhibit significant absorption enhancement when an objects length scale is comparable to or smaller than the wavelength of light. This property has enabled photonic structures to be an integral component in many applications such as solar cells, light emitting diodes, and photothermal therapy. To characterize this enhancement at the single particulate level, conventional methods have consisted of indirect or qualitative approaches which are often limited to certain sample types. To overcome these limitations, we used a bilayer cantilever to directly and quantitatively measure the spectral absorption efficiency of a single silicon microwire in the visible wavelength range. We demonstrate an absorption enhancement on a per unit volume basis compared to a thin film, which shows good agreement with Mie theory calculations. This approach offers a quantitative approach for broadband absorption measurements on a wide range of photonic structures of different geometric and material compositions.

Decoupled cantilever arms for highly versatile and sensitive temperature and heat flux measurements.

Microfabricated cantilever beams have been used in microelectromechanical systems for a variety of sensor and actuator applications. Bimorph cantilevers accurately measure temperature change and heat flux with resolutions several orders of magnitude higher than those of conventional sensors such as thermocouples, semiconductor diodes, as well as resistance and infrared thermometers. The use of traditional cantilevers, however, entails a series of important measurement limitations, because their interactions with the sample and surroundings often create parasitic deflection forces and the typical metal layer degrades the thermal sensitivity of the cantilever. The paper introduces a design to address these issues by decoupling the sample and detector section of the cantilever, along with a thermomechanical model, the fabrication, system integration, and characterization. The custom-designed bi-arm cantilever is over one order of magnitude more sensitive than current commercial cantilevers due to the significantly reduced thermal conductance of the cantilever sample arm. The rigid and immobile sample section offers measurement versatility ranging from photothermal absorption, near-field thermal radiation down to contact, conduction, and material thermal characterization measurements in nearly identical configurations.

Hybrid optical-thermal devices and materials for light manipulation and radiative cooling

We report on optical design and applications of hybrid meso-scale devices and materials that combine optical and thermal management functionalities owing to their tailored resonant interaction with light in visible and infrared frequency bands. We outline a general approach to designing such materials, and discuss two specific applications in detail. One example is a hybrid optical-thermal antenna with sub-wavelength light focusing, which simultaneously enables intensity enhancement at the operating wavelength in the visible and reduction of the operating temperature. The enhancement is achieved via light recycling in the form of whispering-gallery modes trapped in an optical microcavity, while cooling functionality is realized via a combination of reduced optical absorption and radiative cooling. The other example is a fabric that is opaque in the visible range yet highly transparent in the infrared, which allows the human body to efficiently shed energy in the form of thermal emission. Such fabrics can find numerous applications for personal thermal management and for buildings energy efficiency improvement.

Hybrid Optical–Thermal Antennas for Enhanced Light Focusing and Local Temperature Control

Metal nanoantennas supporting localized surface plasmon resonances have become an indispensable tool in bio(chemical) sensing and nanoscale imaging applications. The high plasmon-enhanced electric field intensity in the visible or near-IR range that enables the above applications may also cause local heating of nanoantennas. We present a design of hybrid optical–thermal antennas that simultaneously enable intensity enhancement at the operating wavelength in the visible and nanoscale local temperature control. We demonstrate a possibility to reduce the hybrid antenna operating temperature via enhanced infrared thermal emission. We predict via rigorous numerical modeling that hybrid optical–thermal antennas that support high-quality-factor photonic-plasmonic modes enable up to 2 orders of magnitude enhancement of localized electric fields and of the optical power absorbed in the nanoscale metal volume. At the same time, the hybrid antenna temperature can be lowered by several hundred degrees with respect to...