Xianwen Kan

Fluorescence for the determination of protein with functionalized nano-ZnS

ZnS nanoparticles have been prepared and modified with sodium thioglycolate. The functionalized nanoparticles are water-soluble. They were used as fluorescence probes in the determination of proteins, which was proved to be a simple, rapid and specific method. In comparison with single organic fluorophores, these nanoparticle probes are brighter, more stable against photobleaching, and do not suffer from blinking. Under optimum conditions, linear relationships were found between the enhanced intensity of fluorescence at 441 nm and the concentration of protein in the range 0.1-4.0 microg mL(-1) for human serum albumin (HSA), 0.2-3.0 microg mL(-1) for bovine serum albumin (BSA) and 0.1-4.5 microg mL(-1) for gamma-globulin (gamma-G). The limits of detection were 0.015 microg mL(-1) for HSA, 0.024 microg mL(-1) and 0.017 microg mL(-1) for BSA and gamma-G, respectively. The method has been applied to the analysis of human serum samples collected from the hospital and the results were in good agreement with those reported by a hospital, indicating that the method presented here is not only sensitive and simple, but also reliable and suitable for practical application.

Pyrrole-phenylboronic acid: a novel monomer for dopamine recognition and detection based on imprinted electrochemical sensor.

A molecular imprinting polymer (MIP) based electrochemical sensor was successfully prepared for dopamine (DA) recognition and detection using pyrrole-phenylboronic acid (py-PBA) as a novel electropolymerized monomer. py-PBA could form cyclic boronic ester bond with DA, thus endowing a double recognition capacity of the sensor to DA in the combination of the imprinted effect of MIP. Compared with the sensor prepared using pyrrole or phenylboronic acid as electropolymerized monomer, the present sensor exhibited a remarkable high imprinted factor to DA. The influence factors including pH value, the mole ratio between monomer and template molecule, electropolymerization scan rate, and scan cycles of electropolymerization process were investigated and optimized. Under the optimal conditions, the sensor could recognize DA from its analogs and monosaccharides. A linear ranging from 5.0 × 10(-8) to 1.0 × 10(-5) mol/L for the detection of DA was obtained with a detection limit of 3.3 × 10(-8) mol/L (S/N = 3). The sensor has been applied to analyze DA in injection samples with satisfactory results.

Electrochemical sensor for paracetamol recognition and detection based on catalytic and imprinted composite film

A new strategy for a composite film based electrochemical sensor was developed in this work. A layer of conductive film of poly(p-aminobenzene sulfonic acid) (pABSA) was electropolymerized onto glassy carbon electrode surface and exhibited a high electrocatalytic active for paracetamol (PR) redox. The subsequent formation of a layer of molecular imprinted polymer (MIP) film on pABSA modified electrode endowed the sensor with plentiful imprinted cavities for PR specific adsorption. The advantages of the composite film made the prepared sensor display high sensitivity and good selectivity for PR detection and recognition. Under the optimal conditions, the sensor could recognize PR from its interferents. A linear ranging from 5.0 × 10(-8) to 1.0 × 10(-4)mol/L for PR detection was obtained with a detection limit of 4.3 × 10(-8)mol/L. The sensor has been applied to analyze PR in tablets and human urine samples with satisfactory results. The simple, low cost, and efficient strategy reported here can be further used to prepare electrochemical sensors for other compounds recognition and detection.

CD/AuNPs/MWCNTs based electrochemical sensor for quercetin dual-signal detection

A dual-signal strategy was developed in the present work for quercetin (QR) electrochemical recognition and detection. Mercapto-β-cyclodextrin (HS-β-CD) self-assembled on gold nanoparticles and multi-walled carbon nanotubes modified electrode surface to fabricate an electrochemical sensor. Scanning electron microscope, electrochemical impedance spectroscopy, and cyclic voltammetry were employed to characterize the preparation process of the sensor. Hydroquinone (HQ) was chosen as an electrochemical marker for QR detection due to its small molecular size for the formation of inclusion with HS-β-CD. The results of UV-vis and differential pulse voltammetry demonstrate that the added QR can replace the included HQ in CD cavities, resulting in the dual-signal in electrochemical experiments composed of the decrease of oxidized current of HQ and the increase of oxidized current of QR. Compared with the sensor for QR detection in the absence of HQ, the sensor based dual-signal strategy exhibited a higher sensitivity with a wider detection range from 5.0 × 10(-9) to 7.0 × 10(-6)mol/L. With good selectivity, reproducibility, and stability, the sensor was applied for real samples detection with satisfactory results. The proposed dual-signal strategy can be readily extended to the selective recognition and sensitive detection of other molecules.

Imprinted propyl gallate electrochemical sensor based on graphene/single walled carbon nanotubes/sol–gel film

A novel imprinted sol-gel electrochemical sensor for the determination of propyl gallate (PG) was developed based on a composite of graphene and single walled carbon nanotubes (GR-SWCNTs). It was fabricated by stepwise modifying GR-SWCNTs and molecularly imprinted polymers and stored in 0.10 mol L(-1) phosphate buffer solution pH 6.0, which endowed the sensor good sensitivity and selective recognition towards template molecules. The morphology and specific adsorption capacity of the sensor was characterized by scanning electron microscope and electrochemical methods, respectively. Under the optimized conditions, a linear range of the sensor to PG was 8.0 × 10(-8)-2.6 × 10(-3)mo lL(-1) with a limit of detection of 5.0 × 10(-8)mol L(-1) (S/N=3). The sensor exhibited specificity and selectivity towards template molecules as well as excellent reproducibility, regeneration and stability. Furthermore, the sensor could be applied to determine PG in edible oils, instant noodles and cookies with satisfactory results.

“Sign-on/off” sensing interface design and fabrication for propyl gallate recognition and sensitive detection

A new strategy based on sign-on and sign-off was proposed for propyl gallate (PG) determination by an electrochemical sensor. The successively modified poly(thionine) (PTH) and molecular imprinted polymer (MIP) showed an obvious electrocatalysis and a good recognition toward PG, respectively. Furthermore, the rebound PG molecules in imprinted cavities not only were oxidized but also blocked the electron transmission channels for PTH redox. Thus, a sign-on from PG current and a sign-off from PTH current were combined as a dual-sign for PG detection. Meanwhile, the modified MIP endowed the sensor with recognition capacity. The electrochemical experimental results demonstrated that the prepared sensor possessed good selectivity and high sensitivity. A linear ranging from 5.0×10(-8) to 1.0×10(-4)mol/L for PG detection was obtained with a limit of detection of 2.4×10(-8)mol/L. And the sensor has been applied to analyze PG in real samples with satisfactory results. The simple, low cost, and effective strategy reported here can be further used to prepare electrochemical sensors for other compounds selective recognition and sensitive detection.

Sol-Gel Imprinted Polymers Based Electrochemical Sensor for Paracetamol Recognition and Detection

Molecular imprinting and sol-gel technique were combined to develop a molecular imprinted polymer (MIP) based electrochemical sensor in this work. With the successive modification of multi-walled carbon nanotubes (MWNTs) and gold nanoparticles (GNPs), a modified glassy carbon electrode (GCE) was immersed in a sol-gel solution in the presence of paracetamol (PR) for the electropolymerization to fabricate an imprinted sensor. Scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), and differential pulse voltammetry (DPV) were employed to characterize the constructed sensor. The factors for the sensor preparation, the electropolymerization potential range, the monomer concentration, and the scan rate for the sensor preparation were optimized. The sensor displayed an excellent recognition capacity toward PR compared with other analogues. Additionally, the DPV peak current was linear to the PR concentration in the range from 8.0 × 10−8 to 5.0 × 10−5 mol/L, with a detection limit of 4.0 × 10−8 mol/L. The prepared sensor also showed satisfactory reproducibility and regeneration capacity.