Yingwen Cheng

Design and Synthesis of Hierarchical MnO2 Nanospheres/Carbon Nanotubes/Conducting Polymer Ternary Composite for High Performance Electrochemical Electrodes

For efficient use of metal oxides, such as MnO(2) and RuO(2), in pseudocapacitors and other electrochemical applications, the poor conductivity of the metal oxide is a major problem. To tackle the problem, we have designed a ternary nanocomposite film composed of metal oxide (MnO(2)), carbon nanotube (CNT), and conducting polymer (CP). Each component in the MnO(2)/CNT/CP film provides unique and critical function to achieve optimized electrochemical properties. The electrochemical performance of the film is evaluated by cyclic voltammetry, and constant-current charge/discharge cycling techniques. Specific capacitance (SC) of the ternary composite electrode can reach 427 F/g. Even at high mass loading and high concentration of MnO(2) (60%), the film still showed SC value as high as 200 F/g. The electrode also exhibited excellent charge/discharge rate and good cycling stability, retaining over 99% of its initial charge after 1000 cycles. The results demonstrated that MnO(2) is effectively utilized with assistance of other components (fFWNTs and poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) in the electrode. Such ternary composite is very promising for the next generation high performance electrochemical supercapacitors.

Synergistic effects from graphene and carbon nanotubes enable flexible and robust electrodes for high-performance supercapacitors.

Flexible and lightweight energy storage systems have received tremendous interest recently due to their potential applications in wearable electronics, roll-up displays, and other devices. To manufacture such systems, flexible electrodes with desired mechanical and electrochemical properties are critical. Herein we present a novel method to fabricate conductive, highly flexible, and robust film supercapacitor electrodes based on graphene/MnO(2)/CNTs nanocomposites. The synergistic effects from graphene, CNTs, and MnO(2) deliver outstanding mechanical properties (tensile strength of 48 MPa) and superior electrochemical activity that were not achieved by any of these components alone. These flexible electrodes allow highly active material loading (71 wt % MnO(2)), areal density (8.80 mg/cm(2)), and high specific capacitance (372 F/g) with excellent rate capability for supercapacitors without the need of current collectors and binders. The film can also be wound around 0.5 mm diameter rods for fabricating full cells with high performance, showing significant potential in flexible energy storage devices.

More than the Ions: The Effects of Silver Nanoparticles on Lolium multiflorum

Silver nanoparticles (AgNPs) are increasingly used as antimicrobial additives in consumer products and may have adverse impacts on organisms when they inadvertently enter ecosystems. This study investigated the uptake and toxicity of AgNPs to the common grass, Lolium multiflorum. We found that root and shoot Ag content increased with increasing AgNP exposures. AgNPs inhibited seedling growth. While exposed to 40 mg L(-1) GA-coated AgNPs, seedlings failed to develop root hairs, had highly vacuolated and collapsed cortical cells and broken epidermis and rootcap. In contrast, seedlings exposed to identical concentrations of AgNO(3) or supernatants of ultracentrifuged AgNP solutions showed no such abnormalities. AgNP toxicity was influenced by total NP surface area with smaller AgNPs (6 nm) more strongly affecting growth than did similar concentrations of larger (25 nm) NPs for a given mass. Cysteine (which binds Ag(+)) mitigated the effects of AgNO(3) but did not reduce the toxicity of AgNP treatments. X-ray spectro-microscopy documented silver speciation within exposed roots and suggested that silver is oxidized within plant tissues. Collectively, this study suggests that growth inhibition and cell damage can be directly attributed either to the nanoparticles themselves or to the ability of AgNPs to deliver dissolved Ag to critical biotic receptors.

Size-Controlled Dissolution of Organic-Coated Silver Nanoparticles

The solubility of Ag NPs can affect their toxicity and persistence in the environment. We measured the solubility of organic-coated silver nanoparticles (Ag NPs) having particle diameters ranging from 5 to 80 nm that were synthesized using various methods, and with different organic polymer coatings including poly(vinylpyrrolidone) and gum arabic. The size and morphology of Ag NPs were characterized by transmission electron microscopy (TEM). X-ray absorption fine structure (XAFS) spectroscopy and synchrotron-based total X-ray scattering and pair distribution function (PDF) analysis were used to determine the local structure around Ag and evaluate changes in crystal lattice parameters and structure as a function of NP size. Ag NP solubility dispersed in 1 mM NaHCO(3) at pH 8 was found to be well correlated with particle size based on the distribution of measured TEM sizes as predicted by the modified Kelvin equation. Solubility of Ag NPs was not affected by the synthesis method and coating as much as by their size. Based on the modified Kelvin equation, the surface tension of Ag NPs was found to be ∼1 J/m(2), which is expected for bulk fcc (face centered cubic) silver. Analysis of XAFS, X-ray scattering, and PDFs confirm that the lattice parameter, a, of the fcc crystal structure of Ag NPs did not change with particle size for Ag NPs as small as 6 nm, indicating the absence of lattice strain. These results are consistent with the finding that Ag NP solubility can be estimated based on TEM-derived particle size using the modified Kelvin equation for particles in the size range of 5-40 nm in diameter.

Significantly Improved Long-Cycle Stability in High-Rate Li–S Batteries Enabled by Coaxial Graphene Wrapping over Sulfur-Coated Carbon Nanofibers

Long-term instability of Li-S batteries is one of their major disadvantages compare to other secondary batteries. The reasons for the instability include dissolution of polysulfide intermediates and mechanical instability of the electrode film caused by volume changes during charging/discharging cycles. In this paper, we report a novel graphene-sulfur-carbon nanofibers (G-S-CNFs) multilayer and coaxial nanocomposite for the cathode of Li-S batteries with increased capacity and significantly improved long-cycle stability. Electrodes made with such nanocomposites were able to deliver a reversible capacity of 694 mA h g(-1) at 0.1C and 313 mA h g(-1) at 2C, which are both substantially higher than electrodes assembled without graphene wrapping. More importantly, the long-cycle stability was significantly improved by graphene wrapping. The cathode made with G-S-CNFs with a initial capacity of 745 mA h g(-1) was able to maintain ~273 mA h g(-1) even after 1500 charge-discharge cycles at a high rate of 1C, representing an extremely low decay rate (0.043% per cycle after 1500 cycles). In contrast, the capacity of an electrode assembled without graphene wrapping decayed dramatically with a 10 times high rate (~0.40% per cycle after 200 cycles). These results demonstrate that the coaxial nanocomposites are of great potential as the cathode for high-rate rechargeable Li-S batteries. Such improved rate capability and cycle stability could be attributed to the unique coaxial architecture of the nanocomposite, in which the contributions from graphene and CNFs enable electrodes with improved electrical conductivity, better ability to trap soluble the polysulfides intermediate and accommodate volume expansion/shrinkage of sulfur during repeated charge/discharge cycles.

Improving the performance of cobalt–nickel hydroxide-based self-supporting electrodes for supercapacitors using accumulative approaches

In this paper we describe an accumulative approach to move beyond simple incorporation of conductive carbon nanostructures, such as graphene and carbon nanotubes, to improve the performance of metal oxide/hydroxide based electrodes in energy storage applications. In this approach we first synthesize Co–Ni double hydroxides/graphene binary composites through a co-precipitation process. We then assemble these composites into films (∼6 mg cm−2) by integrating with carbon nanotubes that can be used directly as electrodes. Experimental results indicate that the synergistic contributions from nanotubes, graphene and cobalt substitution enabled electrodes with substantially improved energy storage performance metrics. With 50% Co and 50% Ni (i.e. Co0.5Ni0.5(OH)2), the composite exhibited a remarkable maximum specific capacitance of 2360 F g−1 (360 mA h g−1) at 0.5 A g−1 and still maintained a specific capacitance as high as 2030 F g−1 at 20 A g−1 (∼86% retention). More importantly, the double hydroxides exhibited tunable redox behavior that can be controlled by the ratio between cobalt and nickel. These results demonstrate the importance of the rational design of functional composites and the large-scale assembly strategies for fabricating electrodes with improved performance and tunability for energy storage applications.

Polymeric Coatings on Silver Nanoparticles Hinder Autoaggregation but Enhance Attachment to Uncoated Surfaces

The propensity of silver nanoparticles (AgNPs) having two different polymer coatings (poly(vinylpyrrolidone), PVP, or gum arabic, GA) to aggregate, or to deposit to a reference surface (silica), was explored as a basis for differentiating the effect of surface coating on the stability of nanoparticles in aggregation and in deposition. Surface polymeric coatings stabilize nanoparticles against aggregation as shown by either an increased critical coagulation concentration as for PVP-coated AgNPs (AgPVP) or the absence of observable aggregation even at a high ionic strength as for GA-coated AgNPs (AgGA). In experiments of AgNPs deposition in a silica porous medium, dissimilar surfaces favored deposition, such as the case where polymer coatings were present on the AgNPs but were absent on the porous medium. The increased affinity of the AgNPs for the porous medium in this case may be explained by a shifted contact frontier where electrical double layer interaction is weaker. When coating polymers were introduced to the porous medium and allowed to preadsorb to the silica surfaces, the attachment efficiencies for both the AgPVP and AgGA were reduced due to steric and electrosteric stabilization, respectively. The results suggest that polymeric coatings that are usually deemed as stabilizers (as they indeed are in the case of autoaggregation) might not necessarily stabilize nanoparticles against deposition unless the collector surfaces are also coated with polymer.

Highly reversible Mg insertion in nanostructured Bi for Mg ion batteries

Rechargeable magnesium batteries have attracted wide attention for energy storage. Currently, most studies focus on Mg metal as the anode, but this approach is still limited by the properties of the electrolyte and poor control of the Mg plating/stripping processes. This paper reports the synthesis and application of Bi nanotubes as a high-performance anode material for rechargeable Mg ion batteries. The nanostructured Bi anode delivers a high reversible specific capacity (350 mAh/gBi or 3430 mAh/cm(3)Bi), excellent stability, and high Coulombic efficiency (95% initial and very close to 100% afterward). The good performance is attributed to the unique properties of in situ formed, interconnected nanoporous bismuth. Such nanostructures can effectively accommodate the large volume change without losing electric contact and significantly reduce diffusion length for Mg(2+). Significantly, the nanostructured Bi anode can be used with conventional electrolytes which will open new opportunities to study Mg ion battery chemistry and further improve its properties.

Deposition of silver nanoparticles in geochemically heterogeneous porous media: predicting affinity from surface composition analysis.

The transport of uncoated silver nanoparticles (AgNPs) in a porous medium composed of silica glass beads modified with a partial coverage of iron oxide (hematite) was studied and compared to that in a porous medium composed of unmodified glass beads (GB). At a pH lower than the point of zero charge (PZC) of hematite, the affinity of AgNPs for a hematite-coated glass bead (FeO-GB) surface was significantly higher than that for an uncoated surface. There was a linear correlation between the average nanoparticle affinity for media composed of mixtures of FeO-GB and GB collectors and the relative composition of those media as quantified by the attachment efficiency over a range of mixing mass ratios of the two types of collectors, so that the average AgNPs affinity for these media is readily predicted from the mass (or surface) weighted average of affinities for each of the surface types. X-ray photoelectron spectroscopy (XPS) was used to quantify the composition of the collector surface as a basis for predicting the affinity between the nanoparticles for a heterogeneous collector surface. A correlation was also observed between the local abundances of AgNPs and FeO on the collector surface.

Silver nanoparticle-alginate composite beads for point-of-use drinking water disinfection.

Silver nanoparticles (AgNPs)-alginate composite beads were synthesized using three different approaches as filler materials of packed columns for simultaneous filtration-disinfection as an alternative portable water treatment process. The prepared composite beads were packed into a column through which Escherichia coli containing water was filtered to evaluate the disinfection efficacy. Excellent disinfection performance (no detectable viable colony) was achieved with a hydraulic retention time (HRT) as short as 1 min (the shortest tested) with the SGR (Simultaneous-Gelation-Reduction) and AR (Adsorption-Reduction) beads that were prepared using in situ reduction of Ag(+). Comparatively, the SGR beads released significantly less Ag(+)/AgNPs than the AR beads did within the same HRT. From the results of this study it was identified that SGR may be the best choice among all three different synthesis approaches in that the SGR beads can achieve satisfactory bactericidal performance with a relatively low material consumption rate.