Youngbin Lee

Roll-to-roll production of 30-inch graphene films for transparent electrodes

The outstanding electrical, mechanical and chemical properties of graphene make it attractive for applications in flexible electronics. However, efforts to make transparent conducting films from graphene have been hampered by the lack of efficient methods for the synthesis, transfer and doping of graphene at the scale and quality required for applications. Here, we report the roll-to-roll production and wet-chemical doping of predominantly monolayer 30-inch graphene films grown by chemical vapour deposition onto flexible copper substrates. The films have sheet resistances as low as approximately 125 ohms square(-1) with 97.4% optical transmittance, and exhibit the half-integer quantum Hall effect, indicating their high quality. We further use layer-by-layer stacking to fabricate a doped four-layer film and measure its sheet resistance at values as low as approximately 30 ohms square(-1) at approximately 90% transparency, which is superior to commercial transparent electrodes such as indium tin oxides. Graphene electrodes were incorporated into a fully functional touch-screen panel device capable of withstanding high strain.1 SKKU Advanced Institute of Nanotechnology (SAINT) and Center for Human Interface Nano Technology (HINT), 2 Department of Chemistry, 3 Department of Mechanical Engineering, 4 School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon 440-746, Korea. 5 NanoCore & Department of Physics, National University of Singapore, Singapore 117576 & 117542, 6 Digital & IT Solution Division, Samsung Techwin, Seongnam 462-807, Korea, 7 Nanotube Research Center, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba 305-8565 & Faculty of Science and Engineering, Meijo University, Nagoya 468-8502, Japan.

Wafer-Scale Synthesis and Transfer of Graphene Films

We developed means to produce wafer scale, high-quality graphene films as large as 3 in. wafer size on Ni and Cu films under ambient pressure and transfer them onto arbitrary substrates through instantaneous etching of metal layers. We also demonstrated the applications of the large-area graphene films for the batch fabrication of field-effect transistor (FET) arrays and stretchable strain gauges showing extraordinary performances. Transistors showed the hole and electron mobilities of the device of 1100 +/- 70 and 550 +/- 50 cm(2)/(V s) at drain bias of -0.75 V, respectively. The piezo-resistance gauge factor of strain sensor was approximately 6.1. These methods represent a significant step toward the realization of graphene devices in wafer scale as well as application in optoelectronics, flexible and stretchable electronics.

High‐Performance Perovskite–Graphene Hybrid Photodetector

A high-performance novel photodetector is demonstrated, which consists of graphene and CH3 NH3 PbI3 perovskite layers. The resulting hybrid photodetector exhibits a dramatically enhanced photo responsivity (180 A/W) and effective quantum efficiency (5× 10(4) %) over a broad bandwidth within the UV and visible ranges.

Synthesis of wafer-scale uniform molybdenum disulfide films with control over the layer number using a gas phase sulfur precursor

We describe a method for synthesizing large-area and uniform molybdenum disulfide films, with control over the layer number, on insulating substrates using a gas phase sulfuric precursor (H2S) and a molybdenum metal source. The metal layer thickness was varied to effectively control the number of layers (2 to 12) present in the synthesized film. The films were grown on wafer-scale Si/SiO2 or quartz substrates and displayed excellent uniformity and a high crystallinity over the entire area. Thin film transistors were prepared using these materials, and the performances of the devices were tested. The devices displayed an on/off current ratio of 10(5), a mobility of 0.12 cm(2) V(-1) s(-1) (mean mobility value of 0.07 cm(2) V(-1) s(-1)), and reliable operation.

Flexible and Platinum-Free Dye-Sensitized Solar Cells with Conducting- Polymer-Coated Graphene Counter Electrodes

Typically, DSSCs are composed of a mesoporous titaniananocrystal electrode on a transparent conductive oxide (TCO)substrate with ruthenium-based sensitizers on the titania nano-crystals, platinum on the TCO substrate as a counter electrode,and iodine/iodide electrolyte between the two TCO sub-strates.

Graphene induced tunability of the surface plasmon resonance

Tunability of the surface plasmon resonance wavelength is demonstrated by varying the thickness of Al2O3 spacer layer inserted between the graphene and nanoparticles. By varying the spacer layer thickness from 0.3 to 1.8 nm, the resonance wavelength is shifted from 583 to 566 nm. The shift is due to a change in the electromagnetic field coupling strength between the localized surface plasmons excited in the gold nanoparticles and a single layer graphene film. In contrast, when the graphene film is absent from the system, no noticeable shift in the resonance wavelength is observed upon varying the spacer thickness.

Flexible, transparent single-walled carbon nanotube transistors with graphene electrodes.

This paper reports a mechanically flexible, transparent thin film transistor that uses graphene as a conducting electrode and single-walled carbon nanotubes (SWNTs) as a semiconducting channel. These SWNTs and graphene films were printed on flexible plastic substrates using a printing method. The resulting devices exhibited a mobility of ∼ 2 cm(2) V(-1) s -1), On/Off ratio of ∼ 10(2), transmittance of ∼ 81% and excellent mechanical bendability.

GRAPHENE-BASED TRANSPARENT CONDUCTIVE FILMS

Graphene is a promising alternative to indium tin oxide for use in transparent conducting electrodes. We review recent progress in production methods of graphene and its applications in optoelectronic devices such as touch panel screens, organic photovoltaic cells, organic light emitting diodes and thin film transistors. In addition, we discuss important criteria such as optical transmittance, electrical conductivity and work function, which are critical considerations in the integration of graphene conductive films with optoelectronic devices.

Tunable Indirect to Direct Band Gap Transition of Monolayer Sc2CO2 by the Strain Effect

MXene has not yet been investigated in optical applications because it is a newly suggested two-dimensional material. In the present work, the first investigation of the prospects of MXene as a novel optical nanodevice was done by applying strain to monolayer Sc2CO2 using first-principles density-functional theory. This single-layer material experiences an indirect to direct band gap transition with variation of the band gap size at a relatively small critical strain of about 2%. The present work emphasizes that monolayer MXene can become a promising material for an optical nanodevice by modulating the band gap properties using strain engineering.

Graphene/liquid crystal based terahertz phase shifters

Due to its high electrical conductivity and excellent transmittance at terahertz frequencies, graphene is a promising candidate as transparent electrodes for terahertz devices. We demonstrate a liquid crystal based terahertz phase shifter with the graphene films as transparent electrodes. The maximum phase shift is 10.8 degree and the saturation voltage is 5 V with a 50 µm liquid crystal cell. The transmittance at terahertz frequencies and electrical conductivity depending on the number of graphene layer are also investigated. The proposed phase shifter provides a continuous tunability, fully electrical controllability, and low DC voltage operation.