Yukiko Enomoto-Rogers

Curdlan ester derivatives: synthesis, structure, and properties.

A series of ester derivatives of curdlan, which is a β-(1 → 3)-D-glucan extracellularly produced by microorganism, with varying alkyl chain lengths (C2-C12) were synthesized by the heterogeneous reaction using trifluoroacetic anhydride. As a result, high-molecular-weight (Mw ≥ 6 × 10(5)) and fully-acylated curdlan was obtained with relatively high yield (>70%). Thermal stability of curdlan was greatly improved by esterification. Crystallization was observed for curdlan esters with C2-C6 side chains. Both Tg (170 → 50 °C) and Tm (290 → 170 °C) of curdlan esters decreased with increasing the side-chain length. By the increase in the side-chain carbon number, curdlan esters showed lower Youngs modulus and tensile strength, and larger elongation at break. Thus, material properties of curdlan esters can be controlled by changing the side-chain length. It was found that the increase of the side-chain length resulted in the decrease of crystallinity and the change of crystal structures.

Syntheses and characterization of konjac glucomannan acetate and their thermal and mechanical properties.

Fully substituted glucomannan triacetate (GMTAc) (degree of substitution (DS)=3.0) was prepared from konjac glucomannan (KGM) treated with acetic acid and trifluoroacetic anhydride (TFAA). The peaks in the (1)H- and (13)C NMR spectra of GMTAc were assigned in detail based on two-dimensional (DQF-COSY, HSQC and HMBC) NMR analysis. Glucomannan acetate samples (GMAc) with different degrees of substitution (DS=1.3, 1.7, 2.0 and 2.8) were prepared by partial deprotection of GMTAc. Thermal properties of GMAcs including GMTAc were analyzed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Their decomposition temperatures were higher than that of KGM, and increased with increase in DS. DSC measurements revealed that GMAc had a high glass transition temperature in the range of 178-219 °C, which decreased with increase in DS. The samples did not exhibit melting peaks, indicating that the GMAcs were amorphous. All GMAcs formed transparent films upon solvent casting, and tensile tests revealed that GMAc had a higher tensile strength and elongation to break at lower DS (1.3 and 1.7) compared to higher DS (2.0, 2.8 and 3.0). This means that the mechanical properties of GMAc could be controlled by DS.

Syntheses of glucomannan esters and their thermal and mechanical properties

Fully substituted glucomannan (GM) acylates with acyl carbon numbers (n) of 2, 3, 4, 5, 6, 8, 10, and 12 were prepared from konjac GM (KGM) in carboxylic acid/trifluoroacetic anhydride (TFAA). GM acetate acylates (n=3, 4, 5, 8, 12, 16, and 18) were prepared from KGM in acetic acid/carboxylic acid/TFAA. Differential scanning calorimetry (DSC) and X-ray diffraction revealed that the GM esters did not exhibit melting peaks and reflections derived from crystal, indicating they were amorphous. The glass-transition temperatures (Tgs) of the GM esters tended to decrease with increasing acyl carbon number, ranging from 174°C for GM acetate (GMAc) to 64°C for GM laurate (GMLa). Colorless and transparent GM ester films were obtained by solvent casting and thermo-pressing. The mechanical properties of the GM ester films were controlled by the acyl group structure.

Gellan sulfate inhibits Plasmodium falciparum growth and invasion of red blood cells in vitro

Here, we assessed the sulfated derivative of the microbial polysaccharide gellan gum and derivatives of λ and κ-carrageenans for their ability to inhibit Plasmodium falciparum 3D7 and Dd2 growth and invasion of red blood cells in vitro. Growth inhibition was assessed by means of flow cytometry after a 96-h exposure to the inhibitors and invasion inhibition was assessed by counting ring parasites after a 20-h exposure to them. Gellan sulfate strongly inhibited invasion and modestly inhibited growth for both P. falciparum 3D7 and Dd2; both inhibitory effects exceeded those achieved with native gellan gum. The hydrolyzed λ-carrageenan and oversulfated κ-carrageenan were less inhibitory than their native forms. In vitro cytotoxicity and anticoagulation assays performed to determine the suitability of the modified polysaccharides for in vivo studies showed that our synthesized gellan sulfate had low cytotoxicity and anticoagulant activity.

In vitro synthesis of linear α-1,3-glucan and chemical modification to ester derivatives exhibiting outstanding thermal properties

Bio-based polymer is considered as one of potentially renewable materials to reduce the consumption of petroleum resources. We report herein on the one-pot synthesis and development of unnatural-type bio-based polysaccharide, α-1,3-glucan. The synthesis can be achieved by in vitro enzymatic polymerization with GtfJ enzyme, one type of glucosyltransferase, cloned from Streptococcus salivarius ATCC 25975 utilizing sucrose, a renewable feedstock, as a glucose monomer source, via environmentally friendly one-pot water-based reaction. The structure of α-1,3-glucan is completely linear without branches with weight-average molecular weight (Mw) of 700 kDa. Furthermore, acetate and propionate esters of α-1,3-glucan were synthesized and characterized. Interestingly, α-1,3-glucan acetate showed a comparatively high melting temperature at 339 °C, higher than that of commercially available thermoplastics such as PET (265 °C) and Nylon 6 (220 °C). Thus, the discovery of crystalline α-1,3-glucan esters without branches with high thermal stability and melting temperature opens the gate for further researches in the application of thermoplastic materials.

Conformation analysis of d-glucaric acid in deuterium oxide by NMR based on its JHH and JCH coupling constants

d‐Glucaric acid (GA) is an aldaric acid and consists of an asymmetric acyclic sugar backbone with a carboxyl group positioned at either end of its structure (i.e., the C1 and C6 positions). The purpose of this study was to conduct a conformation analysis of flexible GA as a solution in deuterium oxide by NMR spectroscopy, based on J‐resolved conformation analysis using proton–proton (3JHH) and proton–carbon (2JCH and 3JCH) coupling constants, as well as nuclear overhauser effect spectroscopy (NOESY). The 2JCH and 3JCH coupling constants were measured using the J‐resolved heteronuclear multiple bond correlation (HMBC) NMR technique. NOESY correlation experiments indicated that H2 and H5 were in close proximity, despite the fact that these protons were separated by too large distance in the fully extended form of the chain structure to provide a NOESY correlation. The validities of the three possible conformers along the three different bonds (i.e., C2C3, C3C4, and C4C5) were evaluated sequentially based on the J‐coupling values and the NOESY correlations. The results of these analyses suggested that there were three dominant conformers of GA, including conformer 1, which was H2H3:gauche, H3H4:anti, and H4H5:gauche; conformer 2, which was H2H3:gauche, H3H4:anti, and H4H5:anti; and conformer 3, which was H2H3:gauche, H3H4: gauche, and H4H5:anti. These results also suggested that all three of these conformers exist in equilibrium with each other. Lastly, the results of the current study suggested that the conformational structures of GA in solution were ‘bent’ rather than being fully extended. Copyright

Effect of acetylation site on orientation birefringence of cellulose triacetate

The effect of a substitution site on orientation birefringence for cellulose triacetate (CTA) was investigated by the addition of xylan ester. Since CTA has three substitution sites (C-2, C-3, and C-6) while xylan ester has two substitution sites (C-2 and C-3), the change of birefringence by xylan acetate (XylAc) is attributed to the contribution of the C-6 acetyl group. Dynamic mechanical analysis and thermal measurements showed a single glass transition peak, indicating that XylAc is miscible with CTA at any compositions. The orientation birefringence (Δn) of CTA/XylAc films stretched beyond the glass transition temperature increased with increasing the XylAc content. The result for the stretched film suggested that the contribution of acetyl group in the C-2 and C-3 sites to Δn is positive while that in the C-6 is negative. The negative sign for the C-6 site is in agreement with the result simulated by using the molecular dynamics method. In addition, Δn of CTA films containing xylan propionate (or butyrate) indicated that the propionyl and butyryl groups in the C-2 and C-3 sites show positive birefringence similar to the acetyl group.

Syntheses of poly(l-lactide)-block-xylan butyrate-block-poly(l-lactide) triblock copolymers and their properties

Di-hydroxyl-terminated xylan butyrate (XylBu) with two hydroxyl end groups at opposite ends of the polymer was prepared by acid hydrolysis of XylBu. l-Lactide was polymerized on to the hydroxyl groups at both ends of XylBu, by ring opening. Structural characterization of the polymerization products was carried out using GPC and NMR analyses. It was confirmed that the polymerization products were mixtures of a poly(l-lactide) (PLLA)-b-XylBu-b-poly(l-lactide) (PLLA) triblock copolymer and PLLA homopolymer. Crystallization behaviors of the polymerization products were investigated by differential scanning calorimetry measurements and polarizing optical microscopy observation to investigate the effects of the triblock copolymer on crystallization of PLLA components.