Yung-Chan Chen

A cone-shaped 3D carbon nanotube probe for neural recording

A novel cone-shaped 3D carbon nanotube (CNT) probe is proposed as an electrode for applications in neural recording. The electrode consists of CNTs synthesized on the cone-shaped Si (cs-Si) tip by catalytic thermal chemical vapor deposition (CVD). This probe exhibits a larger CNT surface area with the same footprint area and higher spatial resolution of neural recording compared to planar-type CNT electrodes. An approach to improve CNT characteristics by O(2) plasma treatment to modify the CNT surface will be also presented. Electrochemical characterization of O(2) plasma-treated 3D CNT (OT-CNT) probes revealed low impedance per unit area (∼64.5 Ω mm(-2)) at 1 kHz and high specific capacitance per unit area (∼2.5 mF cm(-2)). Furthermore, the OT-CNT probes were employed to record the neural signals of a crayfish nerve cord. Our findings suggest that OT-CNT probes have potential advantages as high spatial resolution and superb electrochemical properties which are suitable for neural recording applications.

An active, flexible carbon nanotube microelectrode array for recording electrocorticograms

A variety of microelectrode arrays (MEAs) has been developed for monitoring intra-cortical neural activity at a high spatio-temporal resolution, opening a promising future for brain research and neural prostheses. However, most MEAs are based on metal electrodes on rigid substrates, and the intra-cortical implantation normally causes neural damage and immune responses that impede long-term recordings. This communication presents a flexible, carbon-nanotube MEA (CMEA) with integrated circuitry. The flexibility allows the electrodes to fit on the irregular surface of the brain to record electrocorticograms in a less invasive way. Carbon nanotubes (CNTs) further improve both the electrode impedance and the charge-transfer capacity by more than six times. Moreover, the CNTs are grown on the polyimide substrate directly to improve the adhesion to the substrate. With the integrated recording circuitry, the flexible CMEA is proved capable of recording the neural activity of crayfish in vitro, as well as the electrocorticogram of a rat cortex in vivo, with an improved signal-to-noise ratio. Therefore, the proposed CMEA can be employed as a less-invasive, biocompatible and reliable neuro-electronic interface for long-term usage.

Flexible UV-Ozone-Modified Carbon Nanotube Electrodes for Neuronal Recording

Adv. Mater. 2010, 22, 2177–2181 2010 WILEY-VCH Verlag G Neurophysiologists have used sharpened metal electrodes to electrically stimulate neuronal activities to investigate the physiological functions of the brain. Moreover, they employed this electrical stimulation to treat diseases such as Parkinson’s disease, dystonia, and chronic pain. As neurons utilize electrical potential difference between their cell membranes to transmit electrical signals, this particular way of communication enables us to record the neuronal activity extracellularly or intracellularly. For the extracellular recording approach, the electrodes are positioned intimately next to neuron cells to record and to stimulate their electrical activity by capacitive coupling. The coupling efficacy of these electrical recordings or interventions depends significantly on the selectivity, sensitivity, charge-transfer characteristics, long-term chemical stability, and interfacial impedance between electrodes and target tissue. The most common approach to further investigate the functional behavior of neurons, is using Si-based multimicroelectrode probes fabricated by the micro-electromechanical system (MEMS) method to replace the conventional electrodes (Ag/AgCl) in the aspect of device-structure improvement and scaling down device sizes. However, Si-based MEMS electrodes are extremely rigid and cannot be deformed inside the organs; therefore, the recorded positions are easily shifted and the target tissues are consequently damaged when the animals are in motion. This will become an obstacle in future long-term implantation and real-time recording applications. An alternative method is the use of flexible electrodes presented by several groups. The authors utilized soft materials, such as poly(dimethylsiloxane), SU-8 epoxy-based negative photoresist, and polyimides, to fabricate microelectrodes that can deform while being attached to the tissues and that can also be fabricated into small-scale devices using MEMS methods. Not only would rigid Si-based MEMS probes damage target tissues, the reduced electrode size also resulted in a significantly increase in impedance that may degrade recording sensitivity and limit the stimulating current deliverable through an electrode. In order to resolve above issues, the impedance of the electrodemust be as low as possible. Carbon nanotubes (CNTs) exhibit intrinsically large surface areas (700–1000m g ), high electrical conductivity, and intriguing physicochemical properties. Most importantly, CNTs are chemically inert and biocompatible. Based on the above, the promising advantages of flexible substrates and CNTs lead the attempt of fabricating CNTs directly on flexible substrates as microelectrodes for neuronal recording. In this work, the feasibilities of growing CNTs on flexible polyimide substrates at low temperatures (400 8C) by catalyst-assisted chemical vapor deposition (CVD) and utilizing the above devices (see the schematic image in Fig. 1a and the photo in Fig. 1b) as electrodes for extracellularly neuronal recording were investigated. The electrical enhancement (by UV-ozone exposure), biocompatibility (by neuron cell cultures), long-term usage and adhesion, and the detection of action-potential signals on crayfish (using flexible UV-ozone-modified CNTelectrodes) were examined. After a series of process optimizations, the 5-nm Ni-catalyst layer and C2H2 (60 sccm)/H2 (10 sccm) process gases at 5 Torr were found to be the optimum CNT growth parameters in this work. Besides, the Au layer could facilitate CNTgrowth. Figure 1c shows that CNTs have been grown on the polyimide substrate with Au layer, while not on that without Au layer (the inset). The high-resolution transmission electron microscopy (HRTEM) image (Fig. 1d) further confirms the successful syntheses of multi-walled carbon nanotubes (MWCNTs) at 400 8C or even down to 350 8C with H2 plasma pretreatment prior to the CVD processing. As shown in the Supporting Information (Fig. S1a),

THE ENHANCEMENT OF NEURAL GROWTH BY AMINO-FUNCTIONALIZATION ON CARBON NANOTUBES AS A NEURAL ELECTRODE

This paper reports the success of amino-functionalization on multi-walled carbon nanotubes (MWCNTs) to promote neuronal cells growth on MWCNT electrode for extracellular recording, attributed to the formation of positive charge of NH(2) molecules on their surfaces. Besides, the surface of MWCNT electrode becomes hydrophilic after amino-functionalization (AF-MWCNTs) which can enhance electrical conductivity because of lower MWCNT/electrolyte interfacial impedance and higher interfacial capacitance. Durability tests show that electrical characteristics of the MWCNTs treated by 2 wt% 1,4-diaminobutane solution (2 wt%-AF-MWCNTs) can last for at least six months in air ambient. The neural recording of crayfish shows that 2 wt%-AF-MWCNTs can provide better capability on detecting action potentials of caudal photoreceptor (CPR) interneuron compared to suction glass pipette from the evidence of a higher S/N ratio (126 versus 23). The amino-functionalized MWCNT electrode is feasible for long-term recording application according to the results of biocompatibility tests. As the MWCNTs were directly synthesized on Si-based substrates by catalyst-assisted thermal chemical vapor deposition (CVD) at a low temperature (400 °C), these self-aligned MWCNT electrodes could be friendly implemented in integrated circuits fabrications.

Interfacing Neurons both Extracellularly and Intracellularly Using Carbon—Nanotube Probes with Long-Term Endurance

This study demonstrates that carbon nanotubes (CNTs) can be fabricated into probes directly, with which neural activity can be monitored and elicited not only extracellularly but also intracellularly. Two types of CNT probes have been made and examined with the escape neural circuit of crayfish, Procambarus clarkia. The CNT probes are demonstrated to have comparable performance to conventional Ag/AgCl (silver/silver cloride) electrodes. Impedance measurement and cyclic voltammetry further indicate that the CNT probes transmit electrical signals through not only capacitive coupling but also resistive conduction. The resistive conduction facilitates the recording of postsynaptic potentials and equilibrium membrane potentials intracellularly as well as the delivery of direct-current stimulation. Furthermore, delivering current stimuli for a long term is found to enhance rather than to degrade the recording capability of the CNT probes. The mechanism of this fruitful result is carefully investigated and discussed. Therefore, our findings here support the suggestion that CNTs are suitable for making biocompatible, durable neural probes of various configurations for diverse applications.

A bidirectional, flexible neuro-electronic interface employing localised stimulation to reduce artifacts

This paper presents a flexible microelectrode array integrated with a single-chip system enabling each electrode both to record and to stimulate neural activity. A novel approach to reducing stimulation artifacts by confining stimulation currents in two adjacent electrodes is designed and verified. In addition, the functionality of the single-chip system is tested by both electrical measurements and biological experiments. Experimental results indicate that the active, flexible microelectrode array will be capable of interfacing with neurons bidirectionally and reliably.

An integrated system for brain machine interface

A wireless recording system for monitoring the different depth of brain is proposed. The 16-channel recording system includes low-noise amplifiers, analog multiplexers, analog to digital converters, Bluetooth module and an information hub. Neural signals are time-division multiplexed and sampled by an on-board 8-bit analog to digital converter at up to 12k sample/s per channel and overall voltage gain is 5000 V/V. Each channel is controlled by a GUI to fit different kinds of neural signals, which can be observed independently in a PC. We have demonstrated that the board could provide a useful measurement of a rats neural signals in vivo. The recorded signals can be further processed by the fast Fourier transform to analyze the recorded neural signal activity.

An implantable microsystem for studying the Parkinson's Disease

The Pakinsons Disease (PD) is one of the most common diseases for the elderly, and is attributed to the degeneration of neurons in the brain. This paper presents a microsystem suitable for recording the neural activity relating to the PD symptons for a long term, as well as for stimulating the neurons in the deep brain. As many studies indicate that changes of low-frequency field potentials correlate with the PD symptoms, eight chopper amplifiers with tunable bandwidth are designed to record not only low-frequency potentials but also neuronal spikes. Two stimulation circuits with adjustable stimulation voltage are also incorporated to investigate how neural activities change with the stimulation condition. Moreover, the microsystem contains wireless modules for both power and data transmission, facilitating long-term implantation. The functionality of microsystem is tested and discussed in this paper.

A neuromorphic microsystem on glass for monitoring fly behaviours automatically

Fruit flies have been an useful animal model for studying genomics. However, observing and analysing the fly behaviours are labour-intensive and time-consuming. This research exploits the Low-Temperature-Poly-Silicon (LTPS) technology to implement a neuromorphic micro-system for monitoring fly behaviours automatically. The system integrates photodiodes, adaptive pixel circuits, and event-triggered address-reporting circuits on a glass substrate. With a chip area greater than 1cm2, flies can move freely above the chip and their positions can be detected and reported automatically.