Zachary Lingley

Environmental durability of protected silver mirrors prepared by plasma beam sputtering

Various overcoat layers have been developed to protect silver mirrors from tarnish and corrosion. However, the mechanisms by which these protective layers improve mirror durability are not fully understood. Mixed flowing gas exposure was used to investigate the corrosion behavior of plasma beam sputtered silver mirrors with different adhesion layer materials. A small amount of nickel in the adhesion layer had a significant impact on the silver-dielectric interface. Additionally, lateral transport of silver was found to be an important factor in the corrosion process. Better stability at all layer interfaces is suggested to improve mirror durability.

Strain-compensated GaAs1−yPy/GaAs1−zBiz/GaAs1−yPy quantum wells for laser applications

GaAs1−zBiz/GaAs1−yPy strained-compensated quantum well (QW) structures for laser applications were grown by metalorganic vapor phase epitaxy. The band offsets for the GaAs1−zBiz/GaAs1−yPy heterojunction were calculated by the density functional theory, and the design of strain-compensated structures was undertaken by the zero stress analysis. The post-growth thermal annealing of the structures dramatically increases the photoluminescence intensity compared to that from as-grown GaAs1−zBiz QW samples. Transmission electron microscopy studies verified layer thicknesses as well as the presence of abrupt interfaces in the annealed GaAs1−zBiz/GaAs1−yPy QW structure. Electroluminescence measurements from ridge-waveguide devices show broad spectral emission characteristics and lasing was not observed up to a current injection of 4 kA cm−2.

Reliability, failure modes, and degradation mechanisms in high power single- and multi-mode InGaAs-AlGaAs strained quantum well lasers

High power single-mode (SM) and multi-mode (MM) InGaAs-AlGaAs strained quantum well (QW) lasers are critical components for both telecommunications and potential space satellite communications systems. However, little has been reported on failure modes of state-of-the-art SM InGaAs-AlGaAs strained QW lasers although it is crucial to understand failure modes and underlying degradation mechanisms in developing these lasers that meet lifetime requirements for space satellite systems, where extremely high reliability of these lasers is required. Our present study addresses the aforementioned issues by performing long-term life tests under different test conditions followed by failure mode analysis (FMA) and physics of failure investigation. We performed long-term accelerated life-tests on state-of-the-art SM and MM InGaAs-AlGaAs strained QW lasers under ACC (automatic current control) mode. Our life-tests have accumulated over 25,000 test hours for SM lasers and over 35,000 test hours for MM lasers. FMA was performed on failed SM lasers using electron beam induced current (EBIC). This technique allowed us to identify failure types by observing dark line defects. All the SM failures we studied showed catastrophic and sudden degradation and all of these failures were bulk failures. Our group previously reported that bulk failure or COBD (catastrophic optical bulk damage) is the dominant failure mode of MM InGaAs-AlGaAs strained QW lasers. To the best of our knowledge, this is the first report demonstrating that the dominant failure mode of both SM and MM InGaAs-AlGaAs strained QW lasers is the bulk failure. Since degradation mechanisms responsible for COBD are still not well understood, we also employed other techniques including focused ion beam (FIB) processing and high-resolution TEM to further study dark line defects and dislocations in post-aged SM and MM lasers. Our long-term life test results and FMA results are reported.

Conductive paths through polycrystalline BaTiO3: Scanning probe microscopy study

The microstructural features determining the leakage current through polycrystalline BaTiO3 films are investigated using Conductive Atomic Force Microscopy. Grain boundaries are found to be the dominant conductive paths compared to the conduction through the grains. Grain boundary currents are observed to reversibly rise with the increase of the applied DC voltages, indicating that the current is controlled by a field-activated charge transport process.

Degradation mechanisms in high-power multi-mode InGaAs-AlGaAs strained quantum well lasers for high-reliability applications

Laser diode manufacturers perform accelerated multi-cell lifetests to estimate lifetimes of lasers using an empirical model. Since state-of-the-art laser diodes typically require a long period of latency before they degrade, significant amount of stress is applied to the lasers to generate failures in relatively short test durations. A drawback of this approach is the lack of mean-time-to-failure data under intermediate and low stress conditions, leading to uncertainty in model parameters (especially optical power and current exponent) and potential overestimation of lifetimes at usage conditions. This approach is a concern especially for satellite communication systems where high reliability is required of lasers for long-term duration in the space environment. A number of groups have studied reliability and degradation processes in GaAs-based lasers, but none of these studies have yielded a reliability model based on the physics of failure. The lack of such a model is also a concern for space applications where complete understanding of degradation mechanisms is necessary. Our present study addresses the aforementioned issues by performing long-term lifetests under low stress conditions followed by failure mode analysis (FMA) and physics of failure investigation. We performed low-stress lifetests on both MBE- and MOCVD-grown broad-area InGaAs- AlGaAs strained QW lasers under ACC (automatic current control) mode to study low-stress degradation mechanisms. Our lifetests have accumulated over 36,000 test hours and FMA is performed on failures using our angle polishing technique followed by EL. This technique allows us to identify failure types by observing dark line defects through a window introduced in backside metal contacts. We also investigated degradation mechanisms in MOCVD-grown broad-area InGaAs-AlGaAs strained QW lasers using various FMA techniques. Since it is a challenge to control defect densities during the growth of laser structures, we chose to control defect densities by introducing extrinsic point defects to the laser via proton irradiation with different energies and fluences. These lasers were subsequently lifetested to study degradation processes in the lasers with different defect densities and also to study precursor signatures of failures - traps and non-radiative recombination centers (NRCs) in pre- and post-stressed lasers. Lastly, we employed focused ion beam (FIB), electron beam induced current (EBIC), and highresolution TEM (HR-TEM) techniques to further study dark line defects and dislocations in both post-aged and postproton irradiated lasers. We report on our long-term low-stress lifetest results and physics of failure investigation results.

Carrier dynamics in QW and bulk bismide and epitaxial lift off GaAs-In(Al)GaP double heterostructures grown by MOVPE for multi-junction solar cells

III-V multi-junction solar cells are based on a triple-junction design that consists of an InGaP top junction, a GaAs middle junction, and a bottom junction that employs either a 1eV material grown on the GaAs substrate or InGaAs grown on the Ge substrate. The most promising 1 eV materials under extensive investigation are the bulk dilute nitride such as InGaAsN(Sb) lattice-matched to GaAs substrate and the dilute-bismide quantum well materials, such as GaAsBi, strain-compensated with GaAsP barriers. Both approaches have the potential to achieve high performance triple-junction solar cells. In addition, space satellite applications utilizing III-V triple-junction solar cells can have significantly reduced weight and high efficiency. An attractive approach to achieve these goals is to employ full-wafer epitaxial lift off (ELO) technology, which can eliminate the substrate weight and also enable multiple substrate re-usages. For the present study, we employed time-resolved photoluminescence (TR-PL) techniques to study carrier dynamics in MOVPE-grown bulk dilute bismide double heterostructures (DH). Carrier lifetime measurements are crucial to optimizing MOVPE materials growth. We have studied carrier dynamics in GaAsBi QW structures with GaAsP barriers. Carrier lifetimes were measured from GaAsBi DH samples at different stages of post-growth thermal annealing steps. Post-growth annealing yielded significant improvements in carrier lifetimes. Based on this study, single junction solar cells (SJSC) were grown and annealed under a variety of conditions and characterized. The SJSC annealed at 600 – 650 °C exhibited improved response in EQE spectra. In addition, we studied carrier dynamics in MOVPE-grown GaAs-In(Al)GaP DH samples grown on GaAs substrates. The structures were grown on top of a thin AlAs release layer, which allowed epitaxial layers grown on top of the AlAs layer to be removed from the substrate. The GaAs active layers had various doping densities and thicknesses. Our TR-PL results from both pre- and post-ELO processed GaAs-In(Al)GaP DH samples are reported.

Destructive physical analysis of degraded quantum cascade lasers

Remarkable progress made in quantum cascade lasers (QCLs) has led them to find an increasing number of applications in remote sensing, chemical sensing, and free space communications, in addition to potential space applications. However, little has been reported on reliability and failure modes of QCLs although it is crucial to understand failure modes and underlying degradation mechanisms in developing QCLs that meet lifetime requirements for space missions. Focused ion beam (FIB) techniques have been employed to investigate failure modes in various types of laser diodes. Our group has also used FIB to study failure modes in single-mode and multi-mode InGaAs-AlGaAs strained QW lasers, but few groups have used this technique to investigate failure modes in QCLs. In our study, we report on destructive physical analysis (DPA) of degraded InGaAs-InAlAs QCLs using FIB and high-resolution TEM techniques. The active region of QCLs that we studied consisted of two-23 stage layers of InGaAs-InAlAs separated by a 0.5 μm thick InP spacer layer for 8.4μm QCLs and 30-stage layers of lattice-matched InGaAs-InAlAs heterostructure for 4.7μm QCLs. The MOVPE-grown laser structures were fabricated into deep-etched ridge waveguide QCLs. L-I-V-spectral characteristics were measured at RT under pulsed operation. Our 8.4μm QCLs with as-cleaved and HR-coated facets showed a laser threshold of 1.7 A and a threshold voltage of 13 V at RT, whereas our 4.7μm QCLs without facet coating showed threshold currents of 320 - 400 mA and threshold voltages of 13 - 13.5V. Failures were generated via short-term tests of QCLs. FIB systems were used to study the damage area on the front facet and also to prepare TEM cross sections at different locations along the waveguide for defect and chemical analyses using a HR-TEM. In contrast to the COMD damaged area showing as a blister on the front facet of QW lasers, the damaged area of QCLs was significantly extended into the InP substrate due to a much less absorption of lasing photons in QCLs. Our detailed destructive physical analysis results are reported including defect, structural, and chemical analysis results from degraded QCLs.

Root causes investigation of catastrophic optical bulk damage in high-power InGaAs-AlGaAs strained QW lasers

High-power single-mode (SM) and multi-mode (MM) InGaAs-AlGaAs strained quantum well (QW) lasers are critical components for both terrestrial and space satellite communications systems. Since these lasers predominantly fail by catastrophic and sudden degradation due to COD, it is especially crucial for space satellite applications to investigate reliability, failure modes, and degradation mechanisms of these lasers. Our group reported a new failure mode in MM and SM InGaAs-AlGaAs strained QW lasers in 2009 and 2016, respectively. Our group also reported in 2017 that bulk failure due to catastrophic optical bulk damage (COBD) is the dominant failure mode of both SM and MM lasers that were subject to long-term life-tests. For the present study, we report root causes investigation of COBD by performing long-term lifetests followed by failure mode analysis (FMA) using various micro-analytical techniques including electron beam induced current (EBIC), time-resolved electroluminescence (EL), focused ion beam (FIB), high-resolution transmission electron microscopy (TEM), and deep level transient spectroscopy (DLTS). Our life-tests with accumulated test hours of over 25,000 hours for SM lasers and over 35,000 hours for MM lasers generated a number of COBD failures with various failure times. EBIC techniques were employed to study dark line defects (DLDs) generated in SM COBD failures stressed under different test conditions. FIB and high-resolution TEM were employed to prepare cross sectional and plan view TEM specimens to study DLD areas (dislocations) in post-aged SM lasers. Time-resolved EL techniques were employed to study initiation and progressions of dark spots and dark lines in real time as MM lasers were aged. Lastly, to investigate precursor signatures of failure and degradation mechanisms responsible for COBD in both SM and MM lasers, we employed DLTS techniques to study a role that electron traps (non-radiative recombination centers) play in degradation of these lasers. Our in-depth root causes investigation results are reported.

Catastrophic optical bulk degradation in high-power single- and multi-mode InGaAs-AlGaAs strained QW lasers: Part II

High-power single-mode (SM) and multi-mode (MM) InGaAs-AlGaAs strained quantum well (QW) lasers are critical components for both terrestrial and space satellite communications systems. Since these lasers predominantly fail by catastrophic and sudden degradation due to catastrophic optical damage (COD), it is especially crucial for space satellite applications to investigate reliability, failure modes, precursor signatures of failure, and degradation mechanisms of these lasers. Our group reported a new failure mode in MM and SM InGaAs-AlGaAs strained QW lasers in 2009 and 2016, respectively. Our group also reported in 2017 that bulk failure due to catastrophic optical bulk damage (COBD) is the dominant failure mode of both SM and MM lasers that were subject to long-term life-tests. For the present study, we continued our physics of failure investigation by performing long-term life-tests followed by failure mode analysis (FMA) using nondestructive and destructive micro-analytical techniques. We performed long-term accelerated life-tests on state-of-the-art SM and MM InGaAs- AlGaAs strained QW lasers under ACC mode. Our life-tests have accumulated over 25,000 test hours for SM lasers and over 35,000 test hours for MM lasers. We first employed electron beam induced current (EBIC) technique to identify failure modes of degraded SM lasers by observing dark line defects. All the SM failures that we studied showed catastrophic and sudden degradation and all of these failures were bulk failures. Since degradation mechanisms responsible for COBD are still not well understood, we also employed other techniques including focused ion beam (FIB) and high-resolution TEM to further study dark line defects and dislocations in post-aged lasers. Keywor

Effects of adhesion layer composition on the environmental durability of protected silver mirrors

While various layer schemes have been developed to protect thin film silver mirrors from tarnish and corrosion, the mechanisms by which these protective layers improve mirror durability are not fully understood. Mixed flowing gas exposure of plasma beam sputtered silver mirrors was used to investigate how the composition of the very thin adhesion layer changes the mechanism of corrosion feature growth. Two model mirror coatings were analyzed in which the composition of the base layer below the silver and the adhesion layer above were varied. Optical measurements and microscopy, SEM, TEM, and EDS were used to characterize the compositional and chemical effects at the layer interfaces. Large circular corrosion features formed along the silver-chromium interfaces; the addition of nickel to the layers on either side of the silver limited the growth of these features, but resulted in the corrosive attack of the silver itself.