Ahmed Zainelabdin

Luminescence from Zinc Oxide Nanostructures and Polymers and their Hybrid Devices

Zinc oxide (ZnO) is a strong luminescent material, as are several polymers. These two materials have distinct drawbacks and advantages, and they can be combined to form nanostructures with many important applications, e.g., large-area white lighting. This paper discusses the origin of visible emission centers in ZnO nanorods grown with different approaches. White light emitting diodes (LEDs) were fabricated by combining n-ZnO nanorods and hollow nanotubes with different p-type materials to form heterojunctions. The p-type component of the hybrids includes p-SiC, p-GaN, and polymers. We conclude by analyzing the electroluminescence of the different light emitting diodes we fabricated. The observed optical, electrical, and electro-optical characteristics of these LEDs are discussed with an emphasis on the deep level centers that cause the emission.

Influence of pH, precursor concentration, growth time, and temperature on the morphology of ZnO nanostructures grown by the hydrothermal method

We investigated the influence of the pH value, precursor concentration (C), growth time and temperature on the morphology of zinc oxide (ZnO) nanostructures. The pH of the starting solution was varied from1.8 to 12.5. It was found that the final pH reaches an inherent value of 6.6 independently of the initial pH solution. Various ZnO structures of nanotetrapod-like, flower-like, and urchin-like morphology were obtained at alkaline pH (8 to 12.5) whereas for pH solution lower than 8 rod-like nanostructures occurred. Moreover, we observed the erosion of the nanorods for a pH value less than 4.6. By changing the concentrations the density and size were also varied. On going from a high (C > 400mM) to lower (C < 25mM) C, the resulted ZnO nanostructures change from a film to nanorods (NRs) and finally nanowires (NWs). It was also found that the length and diameter of ZnO NRs follow a linear relation with time up to 10 hours, above which no further increase was observed. Finally the effect of growth temperature was seen as an influence on the aspect ratio.

ZnO-organic hybrid white light emitting diodes grown on flexible plastic using low temperature aqueous chemical method

We demonstrate white light luminescence from ZnO-organic hybrid light emitting diodes grown at 90 °C on flexible plastic substrate by aqueous chemical growth. The configuration used for the ZnO-organic hybrid white light emitting diodes (WLEDs) consists of a layer of poly (9, 9-dioctylfluorene) (PFO) on poly (3, 4-ethylenedioxythiophene) poly (styrenesulfonate) coated plastic with top ZnO nanorods. Structural, electrical, and optical properties of these WLEDs were measured and analyzed. Room temperature electroluminescence spectrum reveals a broad emission band covering the range from 420 to 750 nm. In order to distinguish the white light components and contribution of the PFO layer we used a Gaussian function to simulate the experimental data. Color coordinates measurement of the WLED reveals that the emitted light has a white impression. The color rendering index and correlated color temperature of the WLED were calculated to be 68 and 5800 K, respectively.

Zinc oxide nanorods/polymer hybrid heterojunctions for white light emitting diodes

Zinc oxide (ZnO) with its deep level defect emission covering the whole visible spectrum holds promise for the development of intrinsic white lighting sources with no need of using phosphors for light conversion. ZnO nanorods (NRs) grown on flexible plastic as substrate using a low temperature approach (down to 50 °C) were combined with different organic semiconductors to form hybrid junction. White electroluminescence (EL) was observed from these hybrid junctions. The configuration used for the hybrid white light emitting diodes (LEDs) consists of two-layers of polymers on the flexible plastic with ZnO NRs on the top. The inorganic/organic hybrid heterojunction has been fabricated by spin coating the p-type polymer poly (3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT : PSS) for hole injection with an ionization potential of 5.1 eV and poly(9, 9-dioctylfluorene) (PFO) is used as blue emitting material with a bandgap of 3.3 eV. ZnO NRs are grown on top of the organic layers. Two other configurations were also fabricated; these are using a single MEH PPV (red-emitting polymer) instead of the PFO and the third configuration was obtained from a blend of the PFO and the MEH PPV. The white LEDs were characterized by scanning electron microscope, x-ray diffraction (XRD), current–voltage (I–V) characteristics, room temperature photoluminescence (PL) and EL. The EL spectrum reveals a broad emission band covering the range from 420 to 800 nm, and the emissions causing this white luminescence were identified.

Stable White Light Electroluminescence from Highly Flexible Polymer/ZnO Nanorods Hybrid Heterojunction Grown at 50°C

Stable intrinsic white light–emitting diodes were fabricated from c-axially oriented ZnO nanorods (NRs) grown at 50°C via the chemical bath deposition on top of a multi-layered poly(9,9-dioctylfluorene-co–N-(4-butylpheneylamine)diphenylamine)/poly(9,9dioctyl-fluorene) deposited on PEDOT:PSS on highly flexible plastic substrate. The low growth temperature enables the use of a variety of flexible plastic substrates. The fabricated flexible white light–emitting diode (FWLED) demonstrated good electrical properties and a single broad white emission peak extending from 420 nm and up to 800 nm combining the blue light emission of the polyflourene (PFO) polymer layer with the deep level emission (DLEs) of ZnO NRs. The influence of the temperature variations on the FWLED white emissions characteristics was studied and the devices exhibited high operation stability. Our results are promising for the development of white lighting sources using existing lighting glass bulbs, tubes, and armature technologies.

Recent progress on growth and device development of ZnO and CuO nanostructures and graphene nanosheets

Recent progress on the growth of zinc oxide (ZnO), copper oxide (CuO) and graphene nanosheets is presented and discussed. We here restrict the discussion to the hydrothermal low temperature growth regime. In view of this the most critical and important parameters for obtaining nanostructures with desired morphology are discussed and presented. Among all parameters, the temperature and the pH during growth were chosen due to their strong role in affecting the produced nanostructures. The application of this method to non-conventional substrates e.g. paper, is demonstrated. Different devices are fabricated using the grown material and their performance is discussed.

Scale-up synthesis of ZnO nanorods for printing inexpensive ZnO/polymer white light-emitting diode

In this study, possibilities of scaling up the synthesis of zinc oxide (ZnO) nanorods (NRs) by the hydrothermal method have been explored. It was found that batches yielding several grams can easily be made using common and easily available materials. Further, a printable composition was fabricated by mixing the obtained ZnO NRs into a common solvent-based screen printable varnish. Scanning electron microscope, high-resolution transmission electron microscope, X-ray diffraction, UV–vis spectroscopy analysis of the scaled up batch indicated that the ZnO nanostructures were of NRs shape, well crystalline and having less defects. Using the ZnO NRs-based printable composition a device fabrication on a flexible substrate was demonstrated, producing a flexible light-emitting device being highly tolerant to bending.

Influence of the polymer concentration on the electroluminescence of ZnO nanorod/polymer hybrid light emitting diodes

The effects of the polymer concentration on the performance of hybrid light emitting diodes (LEDs) based on zinc oxide nanorods (ZnO NRs) and poly(9,9-dioctylfluorene) (PFO) were investigated. Various characterization techniques were applied to study the performance of the PFO/ZnO NR hybrid LEDs fabricated with various PFO concentrations. The fabricated hybrid LEDs demonstrated stable rectifying diode behavior, and it was observed that the turn-on voltage of the LEDs is concentration dependent. The measured room temperature electroluminescence (EL) showed that the PFO concentration plays a critical role in the emission spectra of the hybrid LEDs. At lower PFO concentrations of 2-6 mg/ml, the EL spectra are dominated by blue emission. However, by increasing the concentration to more than 8 mg/ml, the blue emission was completely suppressed while the green emission was dominant. This EL behavior was explained by a double trap system of excitons that were trapped in the β-phase and/or in the fluorenone defec...

Intrinsic white-light emission from zinc oxide nanorods heterojunctions on large-area substrates

Zinc oxide (ZnO) and especially in the nanostructure form is currently being intensively investigated world wide for the possibility of developing different new photonic devices. We will here present our recent findings on the controlled low temperature chemical growth of ZnO nanorods (NRs) on different large area substrates. Many different heterojunctions of ZnO NRs and p-substrates including those of crystalline e.g. p-GaN, p-SiC or amorphous nature e.g. p-polymer coated plastic and p-polymer coated paper will be shown. Moreover, the effect of the p-electrode of these heterojunctions on tuning the emitted wavelength and changing the light quality will be discussed. An example using ZnO NR/p-GaN will be shown and the electrical and electro-optical characteristics will be analyzed. For these heterojunctions the effect of post growth annealing and its effect on the electroluminescence (EL) spectrum will be shown. Finally, intrinsic white light emitting diodes based on ZnO NRs on foldable and disposable amorphous substrates (plastic and paper) will also be presented.

Nanowires-assembled CuO Interpenetrated-leaf Architecture by ( ) Twinning

High-resolution transmission electron microscopy characterization demonstrates that the petal-like complex three-dimensional (3D) CuO nanomaterial produced by self-assembly in low-temperature wet-chemical synthesis has a unique interpenetrated-leaf structure. The primary leaf consisting of semi-coherent CuO nanocrystallites was formed by bundling, coalescence, and hydrolysis of amorphous Cu (OH)2 nanowires. The petal-like CuO was constructed by growing the secondary leaf on the primary one with a twin relationship ()[010]p//()[]s between them and the twin axis is [101]. The co-axis ⟨010⟩ of leaves is the growth orientation. The 3D complex nanostructure is different from normal low-dimensional nanostructures, e.g. nanorods, nanorings, regarding the formation mechanism and inherent structure.