Bartłomiej Wysocki

Post Processing and Biological Evaluation of the Titanium Scaffolds for Bone Tissue Engineering

Nowadays, post-surgical or post-accidental bone loss can be substituted by custom-made scaffolds fabricated by additive manufacturing (AM) methods from metallic powders. However, the partially melted powder particles must be removed in a post-process chemical treatment. The aim of this study was to investigate the effect of the chemical polishing with various acid baths on novel scaffolds’ morphology, porosity and mechanical properties. In the first stage, Magics software (Materialise NV, Leuven, Belgium) was used to design a porous scaffolds with pore size equal to (A) 200 µm, (B) 500 µm and (C) 200 + 500 µm, and diamond cell structure. The scaffolds were fabricated from commercially pure titanium powder (CP Ti) using a SLM50 3D printing machine (Realizer GmbH, Borchen, Germany). The selective laser melting (SLM) process was optimized and the laser beam energy density in range of 91–151 J/mm3 was applied to receive 3D structures with fully dense struts. To remove not fully melted titanium particles the scaffolds were chemically polished using various HF and HF-HNO3 acid solutions. Based on scaffolds mass loss and scanning electron (SEM) observations, baths which provided most uniform surface cleaning were proposed for each porosity. The pore and strut size after chemical treatments was calculated based on the micro-computed tomography (µ-CT) and SEM images. The mechanical tests showed that the treated scaffolds had Young’s modulus close to that of compact bone. Additionally, the effect of pore size of chemically polished scaffolds on cell retention, proliferation and differentiation was studied using human mesenchymal stem cells. Small pores yielded higher cell retention within the scaffolds, which then affected their growth. This shows that in vitro cell performance can be controlled to certain extent by varying pore sizes.

The Influence of Selective Laser Melting (SLM) Process Parameters on In-Vitro Cell Response

The use of laser 3D printers is very perspective in the fabrication of solid and porous implants made of various polymers, metals, and its alloys. The Selective Laser Melting (SLM) process, in which consolidated powders are fully melted on each layer, gives the possibility of fabrication personalized implants based on the Computer Aid Design (CAD) model. During SLM fabrication on a 3D printer, depending on the system applied, there is a possibility for setting the amount of energy density (J/mm3) transferred to the consolidated powders, thus controlling its porosity, contact angle and roughness. In this study, we have controlled energy density in a range 8–45 J/mm3 delivered to titanium powder by setting various levels of laser power (25–45 W), exposure time (20–80 µs) and distance between exposure points (20–60 µm). The growing energy density within studied range increased from 63 to 90% and decreased from 31 to 13 µm samples density and Ra parameter, respectively. The surface energy 55–466 mN/m was achieved with contact angles in range 72–128° and 53–105° for water and formamide, respectively. The human mesenchymal stem cells (hMSCs) adhesion after 4 h decreased with increasing energy density delivered during processing within each parameter group. The differences in cells proliferation were clearly seen after a 7-day incubation. We have observed that proliferation was decreasing with increasing density of energy delivered to the samples. This phenomenon was explained by chemical composition of oxide layers affecting surface energy and internal stresses. We have noticed that TiO2, which is the main oxide of raw titanium powder, disintegrated during selective laser melting process and oxygen was transferred into metallic titanium. The typical for 3D printed parts post-processing methods such as chemical polishing in hydrofluoric (HF) or hydrofluoric/nitric (HF/HNO3) acid solutions and thermal treatments were used to restore surface chemistry of raw powders and improve surface.

The influence of chemical polishing of titanium scaffolds on their mechanical strength and in-vitro cell response

Selective Laser Melting (SLM) is a powder-bed-based additive manufacturing method, using a laser beam, which can be used to produce metallic scaffolds for bone regeneration. However, this process also has a few disadvantages. One of its drawbacks is the necessity of post-processing in order to improve the surface finish. Another drawback lies in the removal of unmelted powder particles from the build. In this study, the influence of chemical polishing of SLM fabricated titanium scaffolds on their mechanical strength and in vitro cellular response was investigated. Scaffolds with bimodal pore size (200 μm core and 500 μm shell) were fabricated by SLM from commercially pure titanium powder and then chemically treated in HF/HNO3 solutions to remove unmelted powder particles. The cell viability and mechanical strength were compared between as-made and chemically-treated scaffolds. The chemical treatment was successful in the removal of unmelted powder particles from the titanium scaffold. The Youngs modulus of the fabricated cellular structures was of 42.7 and 13.3 GPa for as-made and chemically-treated scaffolds respectively. These values are very similar to the Youngs modulus of living human bone. Chemical treatment did not affect negatively cell proliferation and differentiation. Additionally, the chemically-treated scaffolds had a twofold increase in colonization of osteoblast cells migrating out of multicellular spheroids. Furthermore, X-ray computed microtomography confirmed that chemically-treated scaffolds met the dimensions originally set in the CAD models. Therefore, chemical-treatment can be used as a tool to cancel the discrepancies between the designed and fabricated objects, thus enabling fabrication of finer structures with regular struts and high resolution.