Brandy Armstrong

Quality assurance testing of acoustic doppler current profiler transform matrices

The U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF) is nationally responsible for the design, testing, evaluation, repair, calibration, warehousing, and distribution of hydrologic instrumentation in use within the USGS Water Mission Area (WMA). The HIFs Hydraulic Laboratory has begun routine quality assurance (QA) testing and documenting the performance of every USGS WMA acoustic Doppler current profiler (ADCP) used for making velocity and discharge measurements. All existing ADCPs are being registered and tracked in a database maintained by the HIF, and called for QA checks in the HIFs Hydraulic Laboratory on a 3- year cycle. All new ADCPs purchased directly from the manufacturer as well as ADCPs sent to the HIF or the manufacturer for repair are being registered and tracked in the database and QA checked in the laboratory before being placed into service. Meters failing the QA check are sent directly to the manufacturer for repairs and rechecked by HIF or removed from service. Although this QA program is specific to the SonTek1 and Teledyne RD Instruments1, ADCPs most commonly used within the WMA, it is the intent of the USGS Office of Surface Water and the HIF to expand this program to include all bottom tracking ADCPs as they become available and more widely used throughout the WMA. As part of the HIF QA process, instruments are inspected for physical damage, the instrument must pass the ADCP diagnostic self-check tests, the temperature probe must be within ± 2 degrees Celsius of a National Institute of Standards and Technology traceable reference thermometer and the distance made good over a fixed distance must meet the manufacturers specifications (+/-0.25% or +/-1% difference). The transform matrix is tested by conducting distance-made-good (DMG) tests comparing the straight-line distance from bottom tracking to the measured tow-track distance. The DMG test is conducted on each instrument twice in the forward and reverse directions (4 tows) at four orientations (16 total tows); with beam 1 orientated 0 degrees to the towing direction; turned 45 degrees to the towing direction; turned 90 degrees to the towing direction; and turned 135 degrees to the towing direction. All QA data files and summary results are archived. This paper documents methodology, participation and preliminary results of WMA ADCP QA testing.

Workgroup for hydraulic laboratory testing and verification of hydroacoustic instrumentation

An international workgroup was recently formed for hydraulic laboratory testing and verification of hydroacoustic instrumentation used for water velocity measurements. The activities of the workgroup have included one face to face meeting, conference calls and an inter-laboratory exchange of two acoustic meters among participating laboratories. Good agreement was found among four laboratories at higher tow speeds and poorer agreement at the lowest tow speed.

Observations of ocean circulation and sediment transport experiment offshore of Fire Island, NY

Researchers from the U.S. Geological Survey (USGS) Woods Hole Coastal and Marine Science Center (WHCMSC), in collaboration with Coastal Carolina University (CCU) and University of South Carolina (USC), conducted a scientific field study to investigate the ocean circulation and sediment transport processes offshore of Fire Island, NY. Although the physical processes along the entire linear extent of Fire Island (~50 km) are of interest to the project, one particular region of focus is at the western end of the island where offshore sand ridges out to depths of 20 m extend across the inner shelf and connect to the near-shore bar system. The primary objective was to measure the physical processes around the sand ridges, including circulation patterns, wave parameters, bottom stress, and suspended sediment. Transects of instrumentation were positioned along and across the crests and troughs of the ridge field. A site at the top of a ridge and a site at the bottom of an adjacent trough were each populated with two tripods designed to provide high-resolution measurements near the sea-bed to record sediment re-suspension events. Measurements at these two sites include near bottom velocity profiles, acoustic Doppler velocimeters, pressure, optical transmission and backscatter at high sampling rates. Other measurements include upward looking velocity profiles, temperature, salinity, sonar images and profiles, and sediment size classes. Five smaller tripods were deployed to complete lines alongshore and across shore over a 5 km area to provide a regional picture. These tripods recorded upward looking velocity profiles and near bottom temperature, pressure and salinity. Surface buoys marked the position of the tripods and collected surface measurements at six of the sites. One buoy gathered meteorological measurements. The sites were occupied from January to April, 2012. This deployment was similar to previous efforts off Cape Hatteras, NC, in 2009, and is part of an ongoing effort to understand regional patterns in circulation and sediment transport and the interaction of inner shelf and near shore processes. New instrumentation for the USGS was introduced, including a variety of current and wave measurement equipment, acquisition and telemetry in near-realtime of the weather data, time series sonar imaging equipment, and anti-fouling wipers. Preliminary results suggest a complex and subtle relationship between wind and across shore current velocity in this region, and a more straightforward relationship between winds and alongshore currents. This paper also includes a preliminary report on the effectiveness of new measurement techniques used during this experiment.