Byunghun Lee

A Triple-Loop Inductive Power Transmission System for Biomedical Applications

A triple-loop wireless power transmission (WPT) system equipped with closed-loop global power control, adaptive transmitter (Tx) resonance compensation (TRC), and automatic receiver (Rx) resonance tuning (ART) is presented. This system not only opposes coupling and load variations but also compensates for changes in the environment surrounding the inductive link to enhance power transfer efficiency (PTE) in applications such as implantable medical devices (IMDs). The Tx was built around a commercial off-the-shelf (COTS) radio-frequency identification (RFID) reader, operating at 13.56 MHz. A local Tx loop finds the optimal capacitance in parallel with the Tx coil by adjusting a varactor. A global power control loop maintains the received power at a desired level in the presence of changes in coupling distance, coil misalignments, and loading. Moreover, a local Rx loop is implemented inside a power management integrated circuit (PMIC) to avoid PTE degradation due to the Rx coil surrounding environment and process variations. The PMIC was fabricated in a 0.35- μm 4M2P standard CMOS process with 2.54 mm2 active area. Measurement results show that the proposed triple-loop system improves the overall PTE by up to 10.5% and 4.7% compared to a similar open- and single closed-loop system, respectively, at nominal coil distance of 2 cm. The added TRC and ART loops contribute 2.3% and 1.4% to the overall PTE of 13.5%, respectively. This is the first WPT system to include three loops to dynamically compensate for environment and circuit variations and improve the overall power efficiency all the way from the driver output in Tx to the load in Rx.

A Q-Modulation Technique for Efficient Inductive Power Transmission

A fully integrated power management ASIC for efficient inductive power transmission has been presented capable of automatic load transformation using a method, called Q-modulation. Q-modulation is an adaptive scheme that offers load matching against a wide range of loading (RL) and coupling distance (d23) variations in inductive links to maintain high power transfer efficiency (PTE). It is suitable for inductive powering implantable microelectronic devices (IMDs), recharging mobile electronics, and electric vehicles. In Q-modulation, the zero-crossings of the induced current in the receiver (Rx) LC-tank are detected and a low-loss switch chops the Rx LC-tank for part of the power carrier cycle to form a high-Q LC-tank and store the maximum energy, which is then transferred to RL by opening the switch. By adjusting the duty cycle (D), the loaded-Q of the Rx LC-tank can be dynamically modulated to compensate for variations in RL. A Q-modulation power management (QMPM) prototype chip was fabricated in a 0.35 μm standard CMOS process, occupying 4.8 mm 2. In a 1.45 W wireless power transfer setup, using a class-E power amplifier (PA) operating at 2 MHz, the QMPM successfully increased the inductive link PTE and the overall power efficiency by 98.5% and 120.7% at d23 = 8 cm, respectively, by compensating for 150 Ω variation in RL at D = 45%.

A Smart Wirelessly Powered Homecage for Long-Term High-Throughput Behavioral Experiments

A wirelessly powered homecage system, called the EnerCage-HC, that is equipped with multicoil wireless power transfer, closed-loop power control, optical behavioral tracking, and a graphic user interface is presented for longitudinal electrophysiology and behavioral neuroscience experiments. The EnerCage-HC system can wirelessly power a mobile unit attached to a small animal subject and also track its behavior in real-time as it is housed inside a standard homecage. The EnerCage-HC system is equipped with one central and four overlapping slanted wire-wound coils with optimal geometries to form threeand four-coil power transmission links while operating at 13.56 MHz. Utilizing multicoil links increases the power transfer efficiency (PTE) compared with conventional two-coil links and also reduces the number of power amplifiers to only one, which significantly reduces the system complexity, cost, and heat dissipation. A Microsoft Kinect installed 90 cm above the homecage localizes the animal position and orientation with 1.6-cm accuracy. Moreover, a power management ASIC, including a high efficiency active rectifier and automatic coil resonance tuning, was fabricated in a 0.35-μm 4M2P standard CMOS process for the mobile unit. The EnerCage-HC achieves a max/min PTE of 36.3%/16.1% at the nominal height of 7 cm. In vivo experiments were conducted on freely behaving rats by continuously delivering 24 mW to the mobile unit for >7 h inside a standard homecage.

12.7 A power-management ASIC with Q-modulation capability for efficient inductive power transmission

A wide variety of applications can benefit from near-field wireless power transfer using coupled inductive links, such as wireless sensors and implantable microelectronic devices. The use of inductive power transmission is expected to see an explosive growth over the next decade as engineers try to cut the last cord from mobile electronics, small home appliances, and even electric vehicles [1]. The inductive link power transfer efficiency (PTE) is highly dependent of the loading of the receiver (Rx) coil, referred to as RL. As shown in Fig. 12.7.1a, magnetic resonance-based power transmission in the form of a 3-coil link has been proposed to maximize PTE for any given RL by transforming it to an optimal load, using k34 variable [2,3]. Alternatively, an off-chip matching circuit has been used to transform RL [4]. However, these methods need either an additional coil or a network of off-chip capacitors and inductors, which add to the size/cost of Rx. Moreover, in the above applications, RL can change drastically during operation and there is a need for Rx to dynamically compensate for a wide range of RL to maintain high PTE.

An Inductively-Powered Wireless Neural Recording System With a Charge Sampling Analog Front-End

An inductively-powered wireless integrated neural recording system (WINeR-7) is presented for wireless and battery-less neural recording from freely-behaving animal subjects inside a wirelessly powered standard homecage. The WINeR-7 system employs a novel wide-swing dual slope charge sampling (DSCS) analog front-end (AFE) architecture, which performs amplification, filtering, sampling, and analog-to-time conversion with minimal interference and small amount of power. The output of the DSCS-AFE produces a pseudodigital pulsewidth modulated (PWM) signal. A circular shift register timedivision multiplexes (TDM) the PWM pulses to create a TDMPWM signal, which is fed into an on-chip 915-MHz transmitter (Tx). The AFE and Tx are supplied at 1.8 and 4.2 V, respectively, by a power management block, which includes a high efficiency active rectifier and automatic resonance tuning, operating at 13.56 MHz. The eight-channel system-on-a-chip was fabricated in a 0.35-μm CMOS process, occupying 5×2.5 mm2 and consumed 51.4 mW. For each channel, the sampling rate is 21.48 kHz and the power consumption is 19.3 μW. In vivo experiments were conducted on freely-behaving rats in an energized homecage by continuously delivering 51.4 mW to the WINeR-7 system in a closed-loop fashion and recording local field potentials.

Three-Phase Time-Multiplexed Planar Power Transmission to Distributed Implants

A platform has been presented for wireless powering of receivers (Rxs) that are arbitrarily distributed over a large area. A potential application could be powering of small Rx implants, distributed over large areas of the brain. The transmitter (Tx) consists of three overlapping layers of hexagonal planar spiral coils (hex-PSC) that are horizontally shifted to provide the strongest and most homogeneous electromagnetic flux coverage. The three-layer hex-PSC array is driven by a three-phase time-division-multiplexed power Tx that takes the advantage of the carrier phase shift, coil geometries, and Rx time constant to homogeneously power the arbitrarily distributed Rxs regardless of their misalignments. The functionality of the proposed three-phase power transmission concept has been verified in a detailed scaled-up high-frequency structure simulator Advanced Design System simulation model and measurement setup, and compared with a conventional Tx. The new Tx delivers 5.4 mW to each Rx and achieves, on average, 5.8% power transfer efficiency to the Rx at the worst case 90° angular misalignment, compared with 1.4% by the conventional Tx.

A dual slope charge sampling analog front-end for a wireless neural recording system

This paper presents a novel dual slope charge sampling (DSCS) analog front-end (AFE) architecture, which amplifies neural signals by taking advantage of the charge sampling concept for analog signal conditioning, such as amplification and filtering. The presented DSCS-AFE achieves amplification, filtering, and sampling in a simultaneous fashion, while consuming very small amount of power. The output of the DSCS-AFE produces a pulse width modulated (PWM) signal that is proportional to the input voltage amplitude. A circular shift register (CSR) utilizes time division multiplexing (TDM) of the PWM pulses to create a pseudo-digital TDM-PWM signal that can feed a wireless transmitter. The 8-channel system-on-a-chip was fabricated in a 0.35-μm CMOS process, occupying 2.4 × 2.1 mm2 and consuming 255 μW from a 1.8V supply. Measured input-referred noise for the entire system, including the FPGA in order to recover PWM signal is 6.50 μVrms in the 288 Hz~10 kHz range. For each channel, sampling rate is 31.25 kHz, and power consumption is 31.8 μW.

A Multicycle Q-Modulation for Dynamic Optimization of Inductive Links

This paper presents a new method, called multicycle Q-modulation,to modulate the quality factor (Q) of the receiver (Rx) coil and dynamically optimize the load impedance to maximize the power transfer efficiency (PTE) in two-coil links. A key advantage of the proposed method is that it can be easily implemented using off-the-shelf components without requiring fast switching at or above the carrier frequency, which is more suitable for integrated circuit design. Moreover, the proposed technique does not need any sophisticated synchronization between the power carrier and Q-modulation switching pulses. The multicycle Q-modulation is analyzed theoretically by a lumped circuit model, and verified in simulation and measurement using an off-the-shelf prototype. Automatic resonance tuning in the Rx, combined with multicycle Q-modulation helped maximizing PTE of the inductive link dynamically in the presence of environmental and loading variations, which can otherwise significantly degrade the PTE in multicoil settings. In the prototype conventional two-coil link, the proposed method increased the power amplifier plus inductive-link efficiency from 4.8% to 16.5% at (RL = 1 kW, d23 = 3 cm), and from 23% to 28.2% at (RL = 100 Ω, d23 = 3 cm) after 11% change in the resonance capacitance, while delivering 168.1 mW to the load (PDL).

A smart homecage system with 3D tracking for long-term behavioral experiments

A wirelessly-powered homecage system, called the EnerCage-HC, that is equipped with multi-coil wireless power transfer, closed-loop power control, optical behavioral tracking, and a graphic user interface (GUI) is presented for long-term electrophysiology experiments. The EnerCage-HC system can wirelessly power a mobile unit attached to a small animal subject and also track its behavior in real-time as it is housed inside a standard homecage. The EnerCage-HC system is equipped with one central and four overlapping slanted wire-wound coils (WWCs) with optimal geometries to form 3-and 4-coil power transmission links while operating at 13.56 MHz. Utilizing multi-coil links increases the power transfer efficiency (PTE) compared to conventional 2-coil links and also reduces the number of power amplifiers (PAs) to only one, which significantly reduces the system complexity, cost, and dissipated heat. A Microsoft Kinect installed 90 cm above the homecage localizes the animal position and orientation with 1.6 cm accuracy. An in vivo experiment was conducted on a freely behaving rat by continuously delivering 24 mW to the mobile unit for > 7 hours inside a standard homecage.

Toward a distributed free-floating wireless implantable neural recording system

To understand the complex correlations between neural networks across different regions in the brain and their functions at high spatiotemporal resolution, a tool is needed for obtaining long-term single unit activity (SUA) across the entire brain area. The concept and preliminary design of a distributed free-floating wireless implantable neural recording (FF-WINeR) system are presented, which can enabling SUA acquisition by dispersedly implanting tens to hundreds of untethered 1 mm3 neural recording probes, floating with the brain and operating wirelessly across the cortical surface. For powering FF-WINeR probes, a 3-coil link with an intermediate high-Q resonator provides a minimum S21 of -22.22 dB (in the body medium) and -21.23 dB (in air) at 2.8 cm coil separation, which translates to 0.76%/759 μW and 0.6%/604 μW of power transfer efficiency (PTE) / power delivered to a 9 kΩ load (PDL), in body and air, respectively. A mock-up FF-WINeR is implemented to explore microassembly method of the 1×1 mm2 micromachined silicon die with a bonding wire-wound coil and a tungsten micro-wire electrode. Circuit design methods to fit the active circuitry in only 0.96 mm2 of die area in a 130 nm standard CMOS process, and satisfy the strict power and performance requirements (in simulations) are discussed.