Maysam Ghovanloo

Design and Optimization of Printed Spiral Coils for Efficient Transcutaneous Inductive Power Transmission

The next generation of implantable high-power neuroprosthetic devices such as visual prostheses and brain computer interfaces are going to be powered by transcutaneous inductive power links formed between a pair of printed spiral coils (PSC) that are batch-fabricated using micromachining technology. Optimizing the power efficiency of the wireless link is imperative to minimize the size of the external energy source, heating dissipation in the tissue, and interference with other devices. Previous design methodologies for coils made of 1-D filaments are not comprehensive and accurate enough to consider all geometrical aspects of PSCs with planar 3-D conductors as well as design constraints imposed by implantable device application and fabrication technology. We have outlined the theoretical foundation of optimal power transmission efficiency in an inductive link, and combined it with semi-empirical models to predict parasitic components in PSCs. We have used this foundation to devise an iterative PSC design methodology that starts with a set of realistic design constraints and ends with the optimal PSC pair geometries. We have executed this procedure on two design examples at 1 and 5 MHz achieving power transmission efficiencies of 41.2% and 85.8%, respectively, at 10-mm spacing. All results are verified with simulations using a commercial field solver (HFSS) as well as measurements using PSCs fabricated on printed circuit boards.

Design and Optimization of a 3-Coil Inductive Link for Efficient Wireless Power Transmission

Inductive power transmission is widely used to energize implantable microelectronic devices (IMDs), recharge batteries, and energy harvesters. Power transfer efficiency (PTE) and power delivered to the load (PDL) are two key parameters in wireless links, which affect the energy source specifications, heat dissipation, power transmission range, and interference with other devices. To improve the PTE, a 4-coil inductive link has been recently proposed. Through a comprehensive circuit-based analysis that can guide a design and optimization scheme, we have shown that despite achieving high PTE at larger coil separations, the 4-coil inductive links fail to achieve a high PDL. Instead, we have proposed a 3-coil inductive power transfer link with comparable PTE over its 4-coil counterpart at large coupling distances, which can also achieve high PDL. We have also devised an iterative design methodology that provides the optimal coil geometries in a 3-coil inductive power transfer link. Design examples of 2-, 3-, and 4-coil inductive links have been presented, and optimized for a 13.56-MHz carrier frequency and 12-cm coupling distance, showing PTEs of 15%, 37%, and 35%, respectively. At this distance, the PDL of the proposed 3-coil inductive link is 1.5 and 59 times higher than its equivalent 2- and 4-coil links, respectively. For short coupling distances, however, 2-coil links remain the optimal choice when a high PDL is required, while 4-coil links are preferred when the driver has large output resistance or small power is needed. These results have been verified through simulations and measurements.

Fully integrated wideband high-current rectifiers for inductively powered devices

This paper describes the design and implementation of fully integrated rectifiers in BiCMOS and standard CMOS technologies for rectifying an externally generated RF carrier signal in inductively powered wireless devices, such as biomedical implants, radio-frequency identification (RFID) tags, and smartcards to generate an on-chip dc supply. Various full-wave rectifier topologies and low-power circuit design techniques are employed to decrease substrate leakage current and parasitic components, reduce the possibility of latch-up, and improve power transmission efficiency and high-frequency performance of the rectifier block. These circuits are used in wireless neural stimulating microsystems, fabricated in two processes: the University of Michigans 3-/spl mu/m 1M/2P N-epi BiCMOS, and the AMI 1.5-/spl mu/m 2M/2P N-well standard CMOS. The rectifier areas are 0.12-0.48 mm/sup 2/ in the above processes and they are capable of delivering >25mW from a receiver coil to the implant circuitry. The performance of these integrated rectifiers has been tested and compared, using carrier signals in 0.1-10-MHz range.

The Circuit Theory Behind Coupled-Mode Magnetic Resonance-Based Wireless Power Transmission

Inductive coupling is a viable scheme to wirelessly energize devices with a wide range of power requirements from nanowatts in radio frequency identification tags to milliwatts in implantable microelectronic devices, watts in mobile electronics, and kilowatts in electric cars. Several analytical methods for estimating the power transfer efficiency (PTE) across inductive power transmission links have been devised based on circuit and electromagnetic theories by electrical engineers and physicists, respectively. However, a direct side-by-side comparison between these two approaches is lacking. Here, we have analyzed the PTE of a pair of capacitively loaded inductors via reflected load theory (RLT) and compared it with a method known as coupled-mode theory (CMT). We have also derived PTE equations for multiple capacitively loaded inductors based on both RLT and CMT. We have proven that both methods basically result in the same set of equations in steady state and either method can be applied for short- or midrange coupling conditions. We have verified the accuracy of both methods through measurements, and also analyzed the transient response of a pair of capacitively loaded inductors. Our analysis shows that the CMT is only applicable to coils with high quality factor (Q) and large coupling distance. It simplifies the analysis by reducing the order of the differential equations by half compared to the circuit theory.

Dual-task motor performance with a tongue-operated assistive technology compared with hand operations.

BackgroundTo provide an alternative motor modality for control, navigation, and communication in individuals suffering from impairment or disability in hand functions, a Tongue Drive System (TDS) has been developed that allows for real time tracking of tongue motion in an unobtrusive, wireless, and wearable device that utilizes the magnetic field generated by a miniature disk shaped magnetic tracer attached to the tip of the tongue. The purpose of the study was to compare the influence of a concurrent motor or cognitive task on various aspects of simple movement control between hand and tongue using the TDS technology.MethodsThirteen young able-bodied adults performed rapid and slow goal-directed movements of hand and tongue (with TDS) with and without a concurrent motor (hand or tongue) or cognitive (arithmetic and memory) task. Changes in reaction time, completion time, speed, correctness, accuracy, variability of displacement, and variability of time due to the addition of a concurrent task were compared between hand and tongue.ResultsThe influence of an additional concurrent task on motor performance was similar between the hand and tongue for slow movement in controlling their displacement. In rapid movement with a concurrent motor task, most aspects of motor performance were degraded in hand, while tongue speed during rapid continuous task was maintained. With a concurrent cognitive task, most aspects of motor performance were degraded in tongue, while hand accuracy during the rapid discrete task and hand speed during the rapid continuous task were maintained.ConclusionRapid goal-directed hand and tongue movements were more consistently susceptible to interference from concurrent motor and cognitive tasks, respectively, compared with the other movement.

A wideband frequency-shift keying wireless link for inductively powered biomedical implants

A high data-rate frequency-shift keying (FSK) modulation protocol, a wideband inductive link, and three demodulator circuits have been developed with a data-rate-to-carrier-frequency ratio of up to 67%. The primary application of this novel FSK modulation/demodulation technique is to send data to inductively powered wireless biomedical implants at data rates in excess of 1 Mbps, using comparable carrier frequencies. This method can also be used in other applications such as radio-frequency identification tags and contactless smartcards by adding a back telemetry link. The inductive link utilizes a series-parallel inductive-capacitance tank combination on the transmitter side to provide more than 5 MHz of bandwidth. The demodulator circuits detect data bits by directly measuring the duration of each received FSK carrier cycle, as well as derive a constant frequency clock, which is used to sample the data bits. One of the demodulator circuits, digital FSK, occupies 0.29 mm/sup 2/ in the AMI 1.5-/spl mu/m, 2M/2P, standard CMOS process, and consumes 0.38 mW at 5 V. This circuit is simulated up to 4 Mbps, and experimentally tested up to 2.5 Mbps with a bit error rate of 10/sup -5/, while receiving a 5/10-MHz FSK carrier signal. It is also used in a wireless implantable neural microstimulation system.

A Wide-Band Power-Efficient Inductive Wireless Link for Implantable Microelectronic Devices Using Multiple Carriers

This paper presents a novel inductive link for wireless transmission of power and data to biomedical implantable microelectronic devices using multiple carrier signals. Achieving higher data bandwidth without compromising the power efficiency is the driving force behind using multiple separate carriers. Two separate pairs of coils have been utilized for inductive power and forward data transmission, plus a pair of miniature antennas for back telemetry. One major challenge, however, is to minimize the interference among these carriers especially on the implantable side, where size and power are highly limited. Planar power coils with spiral shape are optimized in geometry to provide maximum coupling coefficient k. The data coils are designed rectangular in shape and wound across the power coils diameter to be oriented perpendicular to the power coil planes. The goal is to maximize data coils direct coupling, while minimize their cross-coupling with the power coils. The effects of coils geometry, orientation, relative distance, and misalignments on the coupling coefficients have been modeled and experimentally evaluated.

An inductively powered scalable 32-channel wireless neural recording system-on-a-chip for neuroscience applications

There has been considerable effort devoted to developing technology for interfacing with the central nervous system in laboratory animals and humans [1–2]. Even though these efforts have led to marvelous technological advancements in circuits and systems, some of the resulting devices may find little use in their application domain, because the specifics of the targeted applications or the realistic needs of the end users may not be taken into account.

A modular 32-site wireless neural stimulation microsystem

This paper presents Interestim-2B, a modular 32-site wireless microstimulating ASIC for neural prosthesis applications, to alleviate disorders such as blindness, deafness, and severe epilepsy. Implanted just below the skull along with a high-density intracortical microelectrode array, the chip enables leadless operation of the resulting microsystem, accepting power and data through an inductive link from the outside world and inserting information into the nervous system in the form of stimulating currents. Each module contains eight current drivers, generating stimulus currents up to /spl plusmn/270 /spl mu/A with 5-b resolution, /spl sim/100M/spl Omega/ output impedance, and a dynamic range (headroom voltage) that extends within 150 mV of the 5 V supply rail, and 250 mV of the ground level. As many as 64 modules can be used in parallel, to drive multiprobe arrays of up to 2048 sites, with only a pair of connections to a common inductive-capacitive (LC) tank circuit, while receiving power (8.25 mW/module) and data (2.5 Mb/s) from a 5/10-MHz frequency shift keyed carrier. Every 4.6 mm /spl times/ 4.6 mm chip fabricated in a 1.5-/spl mu/m, 2M/2P standard CMOS process through MOSIS, houses two modules and generates up to 65 800 stimulus pulses/s.

Modeling and Optimization of Printed Spiral Coils in Air, Saline, and Muscle Tissue Environments

Printed spiral coils (PSCs) are viable candidates for near-field wireless power transmission to the next generation of high-performance neuroprosthetic devices with extreme size constraints, which will target intraocular and intracranial spaces. Optimizing the PSC geometries to maximize the power transfer efficiency of the wireless link is imperative to reduce the size of the external energy source, heating of the tissue, and interference with other devices. Implantable devices need to be hermetically sealed in biocompatible materials and placed in a conductive environment with high permittivity (tissue), which can affect the PSC characteristics. We have constructed a detailed model that includes the effects of the surrounding environment on the PSC parasitic components and eventually on the power transfer efficiency. We have combined this model with an iterative design method that starts with a set of realistic design constraints and ends with the optimal PSC geometries. We applied our design methodology to optimize the wireless link of a 1-cm 2 implantable device example, operating at 13.56 MHz. Measurement results showed that optimized PSC pairs, coated with 0.3 mm of silicone, achieved 72.2%, 51.8%, and 30.8% efficiencies at a face-to-face relative distance of 10 mm in air, saline, and muscle, respectively. The PSC, which was optimized for air, could only bear 40.8% and 21.8% efficiencies in saline and muscle, respectively, showing that by including the PSC tissue environment in the design process the result can be more than a 9% improvement in the power transfer efficiency.