Carolina Assaf Branco

Radiodensity of base, liner and luting dental materials

The aim of this study was to determine the radiodensity of base, liner and luting dental materials and to compare them with human enamel and dentin. Four classes of materials were examined: conventional glass ionomers (CG)—Vitro Cem, Ketac Bond, Vidrion F, Vidrion C; resin-modified glass ionomers (RMGI)—Fuji II LC, Vitrebond; resinous cement (RC)—Rely-X ARC; and zinc phosphate cement (ZP)—Cimento LS. Five 2-mm-thick standard samples of each material and five 2-mm-thick enamel and dentin samples were produced. An aluminum step wedge served as control. Samples were positioned over a phosphor plate of Digora digital system, exposed to X-ray, and the radiodensity obtained in the software Digora for Windows 2.0. Data were submitted to Kruskal–Wallis and Dunnett multiple comparisons test (α=0.05). According to statistical analysis, the following sequence in degree of radiodensity could be seen among the groups: Cimento LS (ZP) > Vitro Cem (CG) = Fuji II LC (RMGI) = Rely-X ARC (RC) = Vitrebond (RMGI) > Ketac Bond (CG) > enamel = Vidrion F (CG) > Vidrion C (CG) = dentin. The presence of radiopaque fillers such as zinc, strontium, zirconium, barium, and lanthanium rather than material type seems to be the most important factor when analyzing material radiodensity. Almost all investigated materials presented an accepted radiodensity.

Influence of powder/liquid ratio on the radiodensity and diametral tensile strength of glass ionomer cements

Objective To determine the influence of P/L ratio on the radiodensity and diametral tensile strength (DTS) of glass ionomer cements. Material and Methods There were 2 factors under study: P/L ratio (manufacturers recommended P/L ratio and a 50% reduced P/L ratio), and materials (Vitro Molar, Vitro Fil, Vitro Cem conventional GICs and Vitro Fil LC, Ortho Glass LC RMGICs). Five 1-mm-thick samples of each material-P/L ratio were produced for radiodensity evaluation. Samples were x-ray exposed onto Digora phosphor plate and radiodensity was obtained using the software Digora for Windows 2.5 Rev 0. For DTS, five (4.0x8.0 mm) cylinder samples of each material were tested (0.5 mm/min). Data were subjected to one- and two-way ANOVA (5x2) followed by Tukeys HSD test, or Kruskal-Wallis and Dunns method. For paired comparisons, t-test or Mann-Whitney test were used (a=0.05). Results There was a significant interaction (P=0.001) for the studied factors (materials vs. P/L ratio). Reduced P/L ratio resulted in significantly lower DTS for the RMGICs, but radiodensity was affected for all materials (P<0.05). Conclusions Reduced P/L ratio affected properties of the tested glass ionomer cements. RMGICs were more susceptible to lower values of DTS, but radiodensity decreased for all materials following P/L ratio reduction.

Dental wear caused by association between bruxism and gastroesophageal reflux disease: a rehabilitation report

Bruxism is a pathological activity of the stomatognathic system that involves tooth grinding and clenching during parafunctional jaw movements. Clinical signs of bruxism are mostly related to dental wear and muscular and joint discomforts, but a large number of etiological factors can be listed, as local, systemic, psychological and hereditary factors. The association between bruxism, feeding and smoking habits and digestive disorders may lead to serious consequences to dental and related structures, involving dental alterations (wear, fractures and cracks), periodontal signs (gingival recession and tooth mobility) and muscle-joint sensitivity, demanding a multidisciplinary treatment plan. This paper presents a case report in which bruxism associated with acid feeding, smoking habit and episodes of gastric reflow caused severe tooth wear and great muscular discomfort with daily headache episodes. From the diagnosis, a multidisciplinary treatment plan was established. The initial treatment approach consisted of medical follow up with counseling on diet and smoking habits and management of the gastric disorders. This was followed by the installation of an interocclusal acrylic device in centric relation of occlusion (CRO) for reestablishment of the occlusal stability, vertical dimension of occlusion, anterior guides and return to normal muscle activity (90-day use approximately). After remission of initial symptoms, oral rehabilitation was implemented in CRO by means of full resin composite restorations and new interocclusal device for protection of restorations. Satisfactory esthetics, improved function and occlusal stability were obtained after oral rehabilitation. The patient has attended annual follow-ups for the past 2 years. The multidisciplinary treatment seems to be the key for a successful rehabilitation of severe cases of dental wear involving the association of different health disorders.

Perception of the signs and symptoms of temporomandibular disorder in females by using the ProTMDMulti protocol and the visual analog scale before and after acupuncture treatment

OBJECTIVE To evaluate the perceptions of patients with TMD in relation to the signs and symptoms before and after acupuncture treatment, according to the ProTMDMulti and the VAS. METHOD 68 patients were divided into groups: muscle TMD treated with acupuncture at local points (MUS-LP), muscle TMD with acupuncture at distant points (MUS-DP), joint and muscle treated with LP (JOI-LP) and joint and muscle treated with DP (JOI-DP). The evaluations were performed at four times: initial, control, final and follow-up. RESULTS The best results were seen in the JOI-LP and the MUS-DP groups, in which the perceptions of the signs and symptoms were statistically lower in the final assessment than in the initial (P<0.05). In all groups, the final and the follow-up evaluations were similar. CONCLUSIONS For TMDs with joint components, the best acupuncture treatment involves local points and for the TMDs with muscle components, points at a distance.Objective: To evaluate the perceptions of patients with TMD in relation to the signs and symptoms before and after acupuncture treatment, according to the ProTMDMulti and the VAS. Method: 68 patients were divided into groups: muscle TMD treated with acupuncture at local points (MUS-LP), muscle TMD with acupuncture at distant points (MUS-DP), joint and muscle treated with LP (JOI-LP) and joint and muscle treated with DP (JOI-DP). The evaluations were performed at four times: initial, control, final and follow-up. Results: The best results were seen in the JOI-LP and the MUS-DP groups, in which the perceptions of the signs and symptoms were statistically lower in the final assessment than in the initial (P<0.05). In all groups, the final and the follow-up evaluations were similar. Conclusions: For TMDs with joint components, the best acupuncture treatment involves local points and for the TMDs with muscle components, points at a distance.