Claudia Cantoni

Low angle grain boundary transport in YBa2Cu3O7−δ coated conductors

Second generation, high-temperature superconducting wires are based on buffered, metallic tape substrates of near single crystal texture. Strong alignment of adjacent grains was found to be necessary from previous work that suggested large angle, YBa2Cu3O7−δ [001]-tilt boundaries reduce Jc exponentially with increasing misorientation angle (θ). We pursue the low-θ regime by evaluating single grain boundaries (GB) and biaxially aligned polycrystalline films utilizing both the rolling-assisted biaxially textured substrates and ion-beam assisted deposition coated conductor architectures. Analysis concludes that an exponential dependence on Jc is applicable for θ≳4°, where the spacing between the periodic disordered regions along the GB become smaller than a coherence length.

Recent progress in the fabrication of high-Jc tapes by epitaxial deposition of YBCO on RABiTS

Abstract Progress made in the fabrication of rolling assisted biaxially textured substrates (RABiTS) and epitaxial deposition or formation of HTS on such substrates is reported. Significant progress has been made in understanding the role of meso-scale defects such as grain boundaries on long-range current flow of HTS conductors made using the RABiTS approach. Both experimental and theoretical calculations suggest that in well-textured samples these commonly present defects do not provide an intrinsic barrier to current flow in long-length conductors. Significant progress has also been made in the reel-to-reel deposition of oxide buffer layers and in the fabrication of long-length superconductors using the ex situ BaF 2 technique. Finally, non-magnetic, mechanically strengthened, biaxially textured metal templates have been fabricated with high quality oxide buffer layers. Epitaxial formation of YBCO on such substrates yields critical current densities over 1 MA/cm 2 at 77 K, 0 T.

Conducting interfaces between band insulating oxides: The LaGaO3/SrTiO3 heterostructure

We show that the growth of the heterostructure LaGaO3/SrTiO3 yields the formation of a highly conductive interface. Our samples were carefully analyzed by high resolution electron microscopy, in order to assess their crystal perfection and to evaluate the abruptness of the interface. Their carrier density and sheet resistance are compared to the case of LaAlO3/SrTiO3 and a superconducting transition is found. The results open the route to widening the field of polar-nonpolar interfaces, pose some phenomenological constrains to their underlying physics and highlight the chance of tailoring their properties for future applications by adopting suitable polar materials.

Electron Transfer and Ionic Displacements at the Origin of the 2D Electron Gas at the LAO/STO Interface: Direct Measurements with Atomic‐Column Spatial Resolution

Using state-of-the-art, aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy with atomic-scale spatial resolution, experimental evidence for an intrinsic electronic reconstruction at the LAO/STO interface is shown. Simultaneous measurements of interfacial electron density and system polarization are crucial for establishing the highly debated origin of the 2D electron gas.

Enhanced flux pinning by BaZrO3 and (Gd,Y)2O3 nanostructures in metal organic chemical vapor deposited GdYBCO high temperature superconductor tapes

We have formed BaZrO3 nanocolumns and (Gd,Y)2O3 nanoprecipitates in reel-to-reel metal organic chemical vapor deposition (MOCVD) processed (Gd,Y)Ba2Cu3O7−x coated conductors and increased the critical currents (Ic) of the conductors in applied magnetic fields to remarkable levels. A (Gd,Y)Ba2Cu3O7−x tape of 1 m in length with 6.5% Zr-additions and 30% composition rich in both Gd and Y showed Ic values of 813 A/cm width at (self-field, 77 K) and above 186 A/cm width at (1 T, 77 K). The strongly enhanced flux pinning over a wide range of magnetic field orientations can be attributed to the bidirectionally aligned defect structures of BaZrO3 and (Gd,Y)2O3 created by optimized MOCVD conditions.

Enhancement of flux pinning in YBa2Cu3O7−δ thin films embedded with epitaxially grown Y2O3 nanostructures using a multi-layering process

Nanodot arrays of Y2O3 were dispersed in thin films of YBa2Cu3O7−δ (YBCO) by growing alternating layers of these two species using a pulsed laser deposition method. As a result, critical current density Jc both in applied magnetic field and self-field is enhanced by as much as an order of magnitude, along with a significant increase in the irreversibility field Hirr. High-resolution scanning transmission electron microscopy (STEM) and Z -contrast STEM show that the nanoparticles are crystalline and coherent with the YBCO matrix. Whereas in most other studies pinning has been attributed to the strain fields around the nanoparticles, in this case pinning may actually be due to the nanoparticles themselves ,s incethe delineation between the two species is very sharp and STEM reveals no discernible strain fields in the superconducting material around the nanoparticles. (Some figures in this article are in colour only in the electronic version)

Strengthened, biaxially textured Ni substrate with small alloying additions for coated conductor applications

Abstract Fabrication of a biaxially textured, strengthened Ni substrate with small alloying additions of W and Fe is reported. The substrates have significantly improved mechanical properties compared to 99.99% Ni and surface characteristics which are similar to that of 99.99% Ni substrates. High quality oxide buffer layers can be deposited on these substrates without the need for any additional surface modification steps. Grain boundary misorientation distributions obtained from the substrate show a predominant fraction of low-angle grain boundaries. A high critical current density, J c , of 1.9 MA/cm 2 at 77 K, self-field is demonstrated on this substrate using a multilayer configuration of YBCO/CeO 2 /YSZ/Y 2 O 3 / Ni–3at.%W–1.7at.%Fe. This translates to a I c /width of 59 A/cm at 77 K and self-field. J c at 0.5 T is reduced by only 21% indicating strongly-linked grain boundaries in the YBCO film on this substrate.

Superconducting magnesium diboride films with Tc≈24 K grown by pulsed laser deposition with in situ anneal

Abstract Thin superconducting films of magnesium diboride (MgB 2 ) with T c ≈24 K were prepared on various oxide substrates by pulsed laser deposition followed by an in situ anneal. A systematic study of the influence of various in situ annealing parameters shows an optimum temperature of about 600°C in a background of 0.7 atm of Ar/4%H 2 for layers consisting of a mixture of magnesium and boron. Contrary to ex situ approaches (e.g. reacting boron films with magnesium vapor at ≈900°C), these films are processed at a temperature at which MgB 2 does not decompose rapidly even in vacuum. This may prove enabling in the formation of multilayers, junctions, and epitaxial films in future work. Issues related to the improvement of these films and to the possible in situ growth of MgB 2 at elevated temperature are discussed.

Fabrication of long lengths of YBCO coated conductors using a continuous reel-to-reel dip-coating unit

A low-cost, non-vacuum, solution precursor route has been developed to produce epitaxial Gd/sub 2/O/sub 3/ and Eu/sub 2/O/sub 3/ buffer layers and YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// (YBCO) superconductors on biaxially textured metal substrates. On sol-gel Eu/sub 2/O/sub 3/ seed layers with sputtered YSZ and CeO/sub 2/ top layers, a YBCO film with a J/sub c/ of over 1 MA/cm/sup 2/ at 77 K was obtained. On all solution buffer layers (CeO/sub 2//Eu/sub 2/O/sub 3//Ni), YBCO film with a J/sub c/ of 200,000 A/cm/sup 2/ at 77 K was grown using pulsed laser deposition (PLD). Meter lengths of epitaxial and crack-free Gd/sub 2/O/sub 3/ buffer layers were fabricated on cube textured Ni-W (3 at.%) substrates for the first time. High quality YBCO films were deposited on Rolling-Assisted Biaxially Textured Substrates (RABiTS) using a trifluoroacetate (TFA) precursor approach. The precursors were either spin-coated or dip-coated and decomposed in a newly developed fast 3-hour burn-out step followed by post-annealing. In a stationary burn-out route, we have produced 40 cm long crack-free YBCO TFA precursors on RABiTS. On short segments, YBCO films with a J/sub c/ of over 500,000 A/cm/sup 2/ at 77 K were grown on all PLD buffered-Ni substrates (CeO/sub 2//YSZ/CeO/sub 2//Ni).

High critical currents in heavily doped (Gd,Y)Ba2Cu3Ox superconductor tapes

REBa2Cu3Ox ((REBCO), RE = rare earth) superconductor tapes with moderate levels of dopants have been optimized for high critical current density in low magnetic fields at 77 K, but they do not exhibit exemplary performance in conditions of interest for practical applications, i.e., temperatures less than 50 K and fields of 2–30 T. Heavy doping of REBCO tapes has been avoided by researchers thus far due to deterioration in properties. Here, we report achievement of critical current densities (Jc) above 20 MA/cm2 at 30 K, 3 T in heavily doped (25 mol. % Zr-added) (Gd,Y)Ba2Cu3Ox superconductor tapes, which is more than three times higher than the Jc typically obtained in moderately doped tapes. Pinning force levels above 1000 GN/m3 have also been attained at 20 K. A composition map of lift factor in Jc (ratio of Jc at 30 K, 3 T to the Jc at 77 K, 0 T) has been developed which reveals the optimum film composition to obtain lift factors above six, which is thrice the typical value. A highly c-axis aligned BaZr...