Emanuel M. Fernandes

Cork: properties, capabilities and applications

Abstract Cork is a natural, renewable, sustainable raw material that has been used for many centuries. As a result of this very long term interest, the scientific literature on cork is extensive. The present review focuses on the chemical composition, physical and mechanical properties of cork and on its products and sub-products. The substantial efforts to fully characterise cork, as well as new developments and evolving research, are reviewed, beginning with its histology, growth and morphology (at macro- and microscales). The chemical structure is analysed in detail, covering both the materials that form the wall structure and the low molecular weight, extractable components. The unique properties of cork are discussed and correlated with current knowledge on morphology and chemical structure. Finally, the important industrial applications of cork are reviewed, in the context of research to provide cork with novel, high added-value applications.

Bioactive macro/micro porous silk fibroin/Nano-sized calcium phosphate scaffolds with potential for bone tissue engineering applications

AIM The development of novel silk/nano-sized calcium phosphate (silk/nano-CaP) scaffolds with highly dispersed CaP nanoparticles in the silk fibroin (SF) matrix for bone tissue engineering. MATERIALS & METHODS Nano-CaP was incorporated in a concentrated aqueous SF solution (16 wt.%) by using an in situ synthesis method. The silk/nano-CaP scaffolds were then prepared through a combination of salt-leaching/lyophilization approaches. RESULTS The CaP particles presented good affinity to SF and their size was inferior to 200 nm when theoretical CaP/silk ratios were between 4 and 16 wt.%, as determined by scanning electron microscopy. The CaP particles displayed a uniform distribution in the scaffolds at both microscopic and macroscopic scales as observed by backscattered scanning electron microscopy and micro-computed tomography, respectively. The prepared scaffolds presented self-mineralization capability and no cytotoxicity confirmed by in vitro bioactivity tests and cell viability assays, respectively. CONCLUSION These results indicated that the produced silk/nano-CaP scaffolds could be suitable candidates for bone-tissue-engineering applications.

New biotextiles for tissue engineering: Development, characterization and in vitro cellular viability

This work proposes biodegradable textile-based structures for tissue engineering applications. We describe the use of two polymers, polybutylene succinate (PBS) proposed as a viable multifilamentand silk fibroin (SF), to produce fibre-based finely tuned porous architectures by weft knitting. PBS is here proposed as a viable extruded multifilament fibre to be processed by a textile-based technology. A comparative study was undertaken using a SF fibre with a similar linear density. The knitted constructs obtained are described in terms of their morphology, mechanical properties, swelling capability, degradation behaviour and cytotoxicity. The weft knitting technology used offers superior control over the scaffold design (e.g. size, shape, porosity and fibre alignment), manufacturing and reproducibility. The presented fibres allow the processing of a very reproducible intra-architectural scaffold geometry which is fully interconnected, thus providing a high surface area for cell attachment and tissue in-growth. The two types of polymer fibre allow the generation of constructs with distinct characteristics in terms of the surface physico-chemistry, mechanical performance and degradation capability, which has an impact on the resulting cell behaviour at the surface of the respective biotextiles. Preliminary cytotoxicity screening showed that both materials can support cell adhesion and proliferation. These results constitute a first validation of the two biotextiles as viable matrices for tissue engineering prior to the development of more complex systems. Given the processing efficacy and versatility of the knitting technology and the interesting structural and surface properties of the proposed polymer fibres it is foreseen that the developed systems could be attractive for the functional engineering of tissues such as skin, ligament, bone or cartilage.

Gradual pore formation in natural origin scaffolds throughout subcutaneous implantation

This study used a rat subcutaneous implantation model to investigate gradual in situ pore formation in a self-regulating degradable chitosan-based material, which comprises lysozyme incorporated into biomimetic calcium phosphate (CaP) coatings at the surface to control the scaffold degradation and subsequent pore formation. Specifically, the in vivo degradation of the scaffolds, the in situ pore formation, and the tissue response were investigated. Chitosan or chitosan/starch scaffolds were studied with and without a CaP coating in the presence or absence of lysozyme for a total of six experimental groups. Twenty-four scaffolds per group were implanted, and eight scaffolds were retrieved at each of three time points (3, 6, and 12 weeks). Harvested samples were analyzed for weight loss, microcomputed tomography, and histological analysis. All scaffolds showed pronounced weight loss and pore formation as a function of time. The highest weight loss was 29.8% ± 1.5%, obtained at week 12 for CaP chitosan/starch scaffolds with lysozyme incorporated. Moreover, all experimental groups showed a significant increase in porosity after 12 weeks. At all time points no adverse tissue reaction was observed, and as degradation increased, histological analysis showed cellular ingrowth throughout the implants. Using this innovative methodology, the ability to gradually generate pores in situ was clearly demonstrated in vivo.

Structural monitoring and modeling of the mechanical deformation of three-dimensional printed poly(ε-caprolactone) scaffolds

Three-dimensional (3D) printed poly(ε-caprolactone) (PCL) based scaffolds have being proposed for different tissue engineering applications. This study addresses the design and fabrication of 3D PCL constructs with different struts alignments at 90°, 45° and 90° with offset. The morphology and the mechanical behavior under uniaxial compressive load were assessed at different strain percentages. The combination of a new compressionCT device and micro computed tomography (micro-CT) allowed understanding the influence of pore geometry under controlled compressive strain in the mechanical and structural behavior of PCL constructs. Finite element analysis (FEA) was applied using the micro-CT data to modulate the mechanical response and compare with the conventional uniaxial compression tests. Scanning electron microscopic analysis showed a very high level of reproducibility and a low error comparing with the theoretical values, confirming that the alignment and the dimensional features of the printed struts are reliable. The mechanical tests showed that the 90° architecture presented the highest stiffness. With the compressionCT device was observed that the 90° and 90° with offset architectures presented similar values of porosity at same strain and similar pore size, contrary to the 45° architecture. Thus, pore geometric configurations affected significantly the deformability of the all PCL scaffolds under compression. The prediction of the FEA showed a good agreement to the conventional mechanical tests revealing the areas more affected under compression load. The methodology proposed in this study using 3D printed scaffolds with compressionCT device and FEA is a framework that offers great potential in understanding the mechanical and structural behavior of soft systems for different applications, including for the biomedical engineering field.

Marine Collagen/Apatite Composite Scaffolds Envisaging Hard Tissue Applications

The high prevalence of bone defects has become a worldwide problem. Despite the significant amount of research on the subject, the available therapeutic solutions lack efficiency. Autografts, the most commonly used approaches to treat bone defects, have limitations such as donor site morbidity, pain and lack of donor site. Marine resources emerge as an attractive alternative to extract bioactive compounds for further use in bone tissue-engineering approaches. On one hand they can be isolated from by-products, at low cost, creating value from products that are considered waste for the fish transformation industry. One the other hand, religious constraints will be avoided. We isolated two marine origin materials, collagen from shark skin (Prionace glauca) and calcium phosphates from the teeth of two different shark species (Prionace glauca and Isurus oxyrinchus), and further proposed to mix them to produce 3D composite structures for hard tissue applications. Two crosslinking agents, 1-[3-(dimethylamino)propyl]-3-ethylcarbodiimide hydrochloride/N-Hydroxysuccinimide (EDC/NHS) and hexamethylene diisocyanate (HMDI), were tested to enhance the scaffolds’ properties, with EDC/NHS resulting in better properties. The characterization of the structures showed that the developed composites could support attachment and proliferation of osteoblast-like cells. A promising scaffold for the engineering of bone tissue is thus proposed, based on a strategy of marine by-products valorisation.

Fish sarcoplasmic proteins as a high value marine material for wound dressing applications

Fish sarcoplasmic proteins (FSP) constitute around 25-30% of the total fish muscle protein. As the FSP are water soluble, FSP were isolated from fresh cod (Gadus morhua) by centrifugation. By SDS-PAGE, it was possible to determine the composition of FSP extracts (FSP-E). The FSP-E undergo denaturation at 44.12 ± 2.34° C, as characterized by differential scanning calorimetry thermograms (DSC). The secondary structure of FSP-E is mainly composed by α-helix structure, as determined by circular dichroism. The cytocompatibility of FSP-E, at concentrations ranging from 5 to 20 mg/mL, was investigated. Concentrations lower than 10 mg/mL have no cytotoxicity cultures of fibroblasts over 72 h. Further on, FSP membranes (FSP-M) were produced by spin coating to evaluate its properties. FSP-M shown having uniform surface as analyzed by Scanning Electron Microscopy (SEM). The relative amount of α-helix structures is higher when compared with the FSP-E. The FSP-M have higher temperature stability than the FSP-E, since they presented a denaturation temperature of 58.88 ± 3.36° C, according to the DSC analysis. FSP-M shown distinctive mechanical properties, with a stiffness of 16.57 ± 3.95 MPa and a yield strength of 23.85 ± 5.97 MPa. Human lung fibroblasts cell lines (MRC-5) were cultured in direct contact with FSP-M, demonstrating its cytocompatibility for 48 h. Based on these results, FSP can be considered a potential biomaterial recovered from nature, for wound dressing applications.

2.11 Polymers of Biological Origin

Recent advances in tissue engineering and regenerative medicine have shown that combining biomaterials, cells, and bioactive molecules are important to promote the regeneration of damaged tissues or as therapeutic systems. Natural origin polymers have been used as matrices in such applications due to their biocompatibility and biodegradability. This article provides an up-to-date review on the most promising natural biopolymers, focused on polysaccharides and proteins, their properties and applications. Membranes, micro/nanoparticles, scaffolds, and hydrogels as biomimetic strategies for tissue engineering and processing are described, along with the use of bioactive molecules and growth factors to improve the tissue regeneration potential. Finally, current biomedical applications are also presented.