Eric DeJong

Processing and analysis of Mars Pathfinder science data at the Jet Propulsion Laboratory's Science Data Processing Systems Section

The Mars Pathfinder mission required new capabilities and adaptation of existing capabilities in order to support science analysis and flight operations requirements imposed by the in situ nature of the mission. The Science Data Processing Systems Section of the Jet Propulsion Laboratory was responsible for the design, development, and application of the system required to perform telemetry processing, distribution, and archiving of data from the four primary science instruments, and support of flight operations through production of automatically generated stereo and color mosaics, terrain visualizations, and animations. The system developed for Mars Pathfinder incorporated new capabilities in producing computer-generated color mosaics, for cataloging and distribution of science data, and utilized new display technology to support science analysis and flight operations requirements. This paper describes the data processing performed to support the science and operations payload on the Pathfinder lander and Sojourner rover.

The solar orbiter imager (SoloHI) instrument for the Solar Orbiter mission

The SoloHI instrument for the ESA/NASA Solar Orbiter mission will track density fluctuations in the inner heliosphere, by observing visible sunlight scattered by electrons in the solar wind. Fluctuations are associated with dynamic events such as coronal mass ejections, but also with the “quiescent” solar wind. SoloHI will provide the crucial link between the low corona observations from the Solar Orbiter instruments and the in-situ measurements on Solar Orbiter and the Solar Probe Plus missions. The instrument is a visible-light telescope, based on the SECCHI/Heliospheric Imager (HI) currently flying on the STEREO mission. In this concept, a series of baffles reduce the scattered light from the solar disk and reflections from the spacecraft to levels below the scene brightness, typically by a factor of 1012. The fluctuations are imposed against a much brighter signal produced by light scattered by dust particles (the zodiacal light/F-corona). Multiple images are obtained over a period of several minutes and are summed on-board to increase the signal-to-noise ratio and to reduce the telemetry load. SoloHI is a single telescope with a 40⁰ field of view beginning at 5° from the Sun center. Through a series of Venus gravity assists, the minimum perihelia for Solar Orbiter will be reduced to about 60 Rsun (0.28 AU), and the inclination of the orbital plane will be increased to a maximum of 35° after the 7 year mission. The CMOS/APS detector is a mosaic of four 2048 x 1930 pixel arrays, each 2-side buttable with 11 μm pixels.

Seeing the corona with the solar probe plus mission: the wide-field imager for solar probe+ (WISPR)

The Solar Probe Plus (SPP) mission scheduled for launch in 2018, will orbit between the Sun and Venus with diminishing perihelia reaching as close as 7 million km (9.86 solar radii) from Sun center. In addition to a suite of in-situ probes for the magnetic field, plasma, and energetic particles, SPP will be equipped with an imager. The Wide-field Imager for the Solar PRobe+ (WISPR), with a 95° radial by 58° transverse field of view, will image the fine-scale coronal structure of the corona, derive the 3D structure of the large-scale corona, and determine whether a dust-free zone exists near the Sun. Given the tight mass constrains of the mission, WISPR incorporates an efficient design of two widefield telescopes and their associated focal plane arrays based on novel large-format (2kx2k) APS CMOS detectors into the smallest heliospheric imaging package to date. The flexible control electronics allow WISPR to collect individual images at cadences up to 1 second at perihelion or sum several of them to increase the signal-to-noise during the outbound part of the orbit. The use of two telescopes minimizes the risk of dust damage which may be considerable close to the Sun. The dependency of the Thomson scattering emission of the corona on the imaging geometry dictates that WISPR will be very sensitive to the emission from plasma close to the spacecraft in contrast to the situation for imaging from Earth orbit. WISPR will be the first ‘local’ imager providing a crucial link between the large scale corona and the in-situ measurements.