Eugene Tam

Uniformity of postprocessing of dense nanotube arrays by neutral and ion fluxes

The advantages of using low-temperature plasma environments for postprocessing of dense nanotube arrays are shown by means of multiscale hybrid numerical simulations. By controlling plasma-extracted ion fluxes and varying the plasma and sheath parameters, one can selectively coat, dope, or functionalize different areas on nanotube surfaces. Conditions of uniform deposition of ion fluxes over the entire nanotube surfaces are obtained for different array densities. The plasma route enables a uniform processing of lateral nanotube surfaces in very dense (with a step-to-height ratio of 1:4) arrays, impossible via the neutral gas process wherein radical penetration into the internanotube gaps is poor.

Growth kinetics of carbon nanowall-like structures in low-temperature plasmas

The results of a hybrid numerical simulation of the growth kinetics of carbon nanowall-like nanostructures in the plasma and neutral gas synthesis processes are presented. The low-temperature plasma-based process was found to have a significant advantage over the purely neutral flux deposition in providing the uniform size distribution of the nanostructures. It is shown that the nanowall width uniformity is the best (square deviations not exceeding 1.05) in high-density plasmas of 3.0× 1018 m-3, worsens in lower-density plasmas (up to 1.5 in 1.0× 1017 m-3 plasmas), and is the worst (up to 1.9) in the neutral gas-based process. This effect has been attributed to the focusing of ion fluxes by irregular electric field in the vicinity of plasma-grown nanostructures on substrate biased with -20 V potential, and differences in the two-dimensional adatom diffusion fluxes in the plasma and neutral gas-based processes. The results of our numerical simulations are consistent with the available experimental reports on the effect of the plasma process parameters on the sizes and shapes of relevant nanostructures.

Controlled synthesis of a large fraction of metallic single-walled carbon nanotube and semiconducting carbon nanowire networks

Controlled synthesis of both single-walled carbon nanotube and carbon nanowire networks using the same CVD reactor and Fe/Al(2)O(3) catalyst by slightly altering the hydrogenation and temperature conditions is demonstrated. Structural, bonding and electrical characterization using SEM, TEM, Raman spectroscopy, and temperature-dependent resistivity measurements suggest that the nanotubes are of a high quality and a large fraction (well above the common 33% and possibly up to 75%) of them are metallic. On the other hand, the carbon nanowires are amorphous and semiconducting and feature a controlled sp(2)/sp(3) ratio. The growth mechanism which is based on the catalyst nanoisland analysis by AFM and takes into account the hydrogenation and temperature control effects explains the observed switch-over of the nanostructure growth modes. These results are important to achieve the ultimate control of chirality, structure, and conductivity of one-dimensional all-carbon networks.

Thermodynamic properties and transport coefficients of arc lamp plasmas: argon, krypton and xenon

Calculated values of the density, specific heat, enthalpy, viscosity, thermal conductivity and electrical conductivity of thermal plasmas formed from three gases used in arc lamps, krypton, argon and xenon, are presented. The calculations, which assume local thermodynamic equilibrium, were performed for pressures from 1 to 100?atm and for the temperature range 300?30?000?K. The results were compared with those of previously published studies. Some discrepancies were found for krypton and xenon; these are attributed to the improved values of the collision integrals used here in calculating the transport coefficients.

Plasma-controlled adatom delivery and (re)distribution: Enabling uninterrupted, low-temperature growth of ultralong vertically aligned single walled carbon nanotubes

Large-scale (∼109 atoms) numerical simulations reveal that plasma-controlled dynamic delivery and redistribution of carbon atoms between the substrate and nanotube surfaces enable the growth of ultralong single walled carbon nanotubes (SWCNTs) and explain the common experimental observation of slower growth at advanced stages. It is shown that the plasma-based processes feature up to two orders of magnitude higher growth rates than equivalent neutral-gas systems and are better suited for the SWCNT synthesis at low nanodevice friendly temperatures.Large-scale (∼109 atoms) numerical simulations reveal that plasma-controlled dynamic delivery and redistribution of carbon atoms between the substrate and nanotube surfaces enable the growth of ultralong single walled carbon nanotubes (SWCNTs) and explain the common experimental observation of slower growth at advanced stages. It is shown that the plasma-based processes feature up to two orders of magnitude higher growth rates than equivalent neutral-gas systems and are better suited for the SWCNT synthesis at low nanodevice friendly temperatures.

Different Nanostructures From Different Plasmas: Nanoflowers and Nanotrees on Silicon

Using the advanced radio-frequency plasma-assisted magnetron deposition system, various nanostructures such as nanoflowers of carbon nanotubes, ZnO nanobelts, and silicon nanotrees were successfully synthesized. In this paper, we present the photographs of ICP and magnetron discharges, the photograph of a complex plasma structure, and the SEM images of various nanostructures synthesized in the system with magnetron and ICP sources operating simultaneously.

Graphene and Carbon Nanotubes From Arc Plasmas: Experiment and Plasma Modeling

Graphene and carbon nanotubes are the most promising nanomaterials for application in various modern nanodevices. The successful production of the nanotubes and graphene in a single process was achieved by using a magnetically enhanced arc discharge in helium atmosphere between carbon and metal electrodes. A 3-D fluid model has been used to investigate the discharge parameters.

Modelling Lightning Initiation and Attachment to Aircraft

We present initial calculations of the formation of streamers on an aircraft. A two-dimensional model has been used to determine electric field strengths and charge densities around solids of various geometries and electrical conductivities. The calculations take into account the distortion of the background electric fields by the solid material and the production and motion of charged species. Detailed time-dependent visualizations of the streamer initiation and propagation are presented. The effects of size and aspect ratio of the gross features of the aircraft on the development of the streamers is discussed.