Hualan Zhou

Immobilization and condensation of DNA with 3-aminopropyltriethoxysilane studied by atomic force microscopy

We used different methods to modify a mica surface with 3‐aminopropyltriethoxysilane (APTES), and then used it as substrate to immobilize DNA for atomic force microscopy (AFM) observation. The evaporation method and solution modifying method were investigated and evaluated. The solution modifying method was found to be relatively simple and effective. Using an APTES solution‐modified mica surface, DNA immobilization appeared more reproducible and it could be imaged in liquid. The mixed solution of APTES and DNA was dropped directly onto the mica surface for AFM imaging. We found that DNA can condense in APTES water solutions. Toroids, rods and intermediate structures of condensation were captured by AFM.

AFM studies of DNA structures on mica in the presence of alkaline earth metal ions

As counterions of DNA on mica, Mg(2+), Ca(2+), Sr(2+) and Ba(2+) were used for clarifying whether DNA molecules equilibrate or are trapped on mica surface. End to end distance and contour lengths were determined from statistical analysis of AFM data. It was revealed that DNA molecules can equilibrate on mica when Mg(2+), Ca(2+) and Sr(2+) are counterions. When Ba(2+) is present, significantly crossovered DNA molecules indicate that it is most difficult for DNA to equilibrate on mica and the trapping degree is different under different preparation conditions. In the presence of ethanol, using AFM we have also observed the dependence of B-A conformational transition on counterion identities. The four alkaline earth metal ions cause the B-A transition in different degrees, in which Sr(2+) induces the greatest structural transition.

The structural transition of DNA-Tris(1,10-phenanthroline) cobalt(III) complexes in ethanol-water solution

The interaction of DNA with Tris(1,10-phenanthroline) cobalt(III) was studied by means of atomic force microscopy. Changes in the morphologies of DNA complex in the presence of ethanol may well indicate the crucial role of electrostatic force in causing DNA condensation. With the increase of the concentration of ethanol, electrostatic interaction is enhanced corresponding to a lower dielectric constant. Counterions condense along the sugar phosphate backbone of DNA when epsilon is lowered and the phosphate charge density can thus be neutralized to the level of DNA condensation. Electroanalytical measurement of DNA condensed with Co(phen)(3)(3+) in ethanol solution indicated that intercalating reaction remains existing. According to both the microscopic and spectroscopic results, it can be found that no secondary structure transition occurs upon DNA condensing. B-A conformation transition takes place at more than 60% ethanol solution.

Construction and control of plasmid DNA network.

The influences of different cations on plasmid DNA network structures on a mica substrate were investigated by atomic force microscopy (AFM). Interactions between the DNA strands and mica substrate, and between the DNA strands themselves were more strongly influenced by the complex cations (Fe(phen)3(2+), Ni(phen)3(2+), and Co(phen)3(3+)) than by the simple cations (Mg2+, Mn2+, Ni2+, Ca2+, Co3+). The mesh height of the plasmid DNA network was higher when the complex cations were added to DNA samples. The mesh size decreased with increasing DNA concentration and increased with decreasing DNA concentration in the same cation solution sample. Hence, plasmid DNA network height can be controlled by selecting different cations, and the mesh size can be controlled by adjusting plasmid DNA concentration.

The influence of tip performance on scanning probe lithography

Abstract Scanning probe lithography (SPL), employing the tip of an atomic force microscope to mechanically pattern various materials in nanoscale region has provided a simple but significant method for making nanostructures. We use this technique for the lithography of several kinds of substrate surfaces. The tip performance has been found to be a crucial factor in the lithographic process. Four types of cantilevers are employed in nanolithography, including standard silicon nitride (DNP), tapping mode™ etched silicon (TESP(W)), uncoated silicon cantilever (NSC21/50) and conductive platinum/iridium-coated probe. Results demonstrate that tips with smaller spring constants can not be used for physically scribing and nanomanipulating in our experiment. The possible mechanism of our experiment is discussed.