J. Muratore

Test Results of the First 3.7 m Long Nb3Sn Quadrupole by LARP and Future Plans

In December 2009 during its first cold test, LQS01, the first Long Nb3Sn Quadrupole made by LARP (LHC Accelerator Research Program, a collaboration of BNL, FNAL, LBNL and SLAC), reached its target field gradient of 200 T/m. This target was set in 2005 by the US Department of Energy, CERN and LARP, as a significant milestone toward the development of Nb3Sn quadrupoles for possible use in LHC luminosity upgrades. LQS01 is a 90 mm aperture, 3.7 m long quadrupole using Nb3Sn coils. The coil layout is equal to the layout used in the LARP Technological Quadrupoles (TQC and TQS models). Pre-stress and support are provided by a segmented aluminum shell pre-loaded using bladders and keys, similarly to the TQS models. After the first test the magnet was disassembled, reassembled with an optimized pre-stress, and reached 222 T/m at 4.5 K. In this paper we present the results of both tests and the next steps of the Long Quadrupole R&D.

About the mechanics of SSC dipole magnet prototypes

During the last two years, nine 4‐cm aperture, 17‐m‐long dipole magnet prototypes were produced by Brookhaven National Laboratory (BNL) under contact with the Superconducting Super Collider (SSC) Laboratory. These prototypes are the last phase of a half‐decade‐long R&D program, carried out in collaboration with Fermi National Accelerator Laboratory and Lawrence Berkeley Laboratory, and aimed at demonstrating the feasibility of the SSC main‐ring dipole magnets. They also lay the groundwork for the 5‐cm‐aperture dipole magnet program now underway. After reviewing the design features of the BNL 4‐cm‐aperture, 17‐m‐long dipole magnets, we describe in detail the various steps of their fabrication. For each step, we discuss the paramaters that need to be mastered, and we compare the values that were achieved for the nine most recent prototypes. The data appear coherent and reproducible, demonstrating that the assembly process is under control. We then analyze the mechanical behavior of these magnets during cool...

Quench antenna for superconducting particle accelerator magnets

We report on the design, fabrication, and test of an assembly of stationary pickup coils which can be used to localize quench origins. After describing the pickup coils configuration, we develop a simple model of current redistribution which allows interpretation of the measured voltages and determination of the turn of the magnet coil in which the quench started. The technique is illustrated by analyzing the data from a quench of a 5-cm-aperture, 15-m-long SSC dipole magnet prototype. >

Superconducting magnet system at the 50 GeV proton beam line for the J-PARC neutrino experiment

A neutrino oscillation experiment using the J-PARC 50 GeV 0.75 MW proton beam is planned as a successor to the K2K project currently being operated at KEK. A superconducting magnet system is required for the arc section of the primary proton beam line to be within the space available at the site. A system with 28 combined function magnets is proposed to simplify the system and optimize the cost. The required fields for the magnets are 2.6 T dipole and 19 T/m quadrupole. The magnets are also required to have a large aperture, 173.4 mm diameter, to accommodate the large beam emittance. The magnets will be protected by cold diodes and cooled by forced flow supercritical helium produced by a 4.5 K, 2/spl sim/2.5 kW refrigerator. This paper reports the system overview and the design status.

Design of

The LHC Accelerator Research Program (LARP) has a primary goal to develop, assemble, and test full size Nb3Sn quadrupole magnet models for a luminosity upgrade of the Large Hadron Collider (LHC). A major milestone in this development is to assemble and test, by the end of 2009, two 4 m-long quadrupole cold masses, which will be the first Nb3Sn accelerator magnet models approaching the length of real accelerator magnets. The design is based on the LARP Technological Quadrupoles (TQ), under development at FNAL and LBNL, with gradient higher than 200 T/m and aperture of 90 mm. The mechanical design will be chosen between two designs presently explored for the TQs: traditional collars and Al-shell based design (preloaded by bladders and keys). The fabrication of the first long quadrupole model is expected to start in the last quarter of 2007. Meanwhile the fabrication of 4 m-long racetrack coils started this year at BNL. These coils will be tested in an Al-shell based supporting structure developed at LBNL. Several challenges have to be addressed for the successful fabrication of long Nb3Sn coils. This paper presents these challenges with comments and solutions adopted or under study for these magnets. The coil design of these magnets, including conductor and insulation features, and quench protection studies are also presented.

{\hbox{Nb}}_{3}{\hbox{Sn}}

The test of the first LARP (LHC Accelerator Research Program) Long Quadrupole is a significant milestone toward the development of Nb3Sn quadrupoles for LHC (Large Hadron Collider) Luminosity Upgrades. These 3.7-m long magnets, scaled from the 1-m long Technological Quadrupoles, are used to develop our capabilities to fabricate and assemble Nb3Sn coils and structures with lengths comparable to accelerator magnet dimensions. The long quadruples have a target gradient of 200 T/m in a 90-mm aperture. Pre-stress and support are provided by an Al-shell-based structure pre-loaded using bladders and keys. The coils were fabricated at BNL and FNAL, the shell-based structure was designed and assembled at LBNL, the test is performed at FNAL. In this paper we present the final steps of the development of the first model (LQS01), several upgrades to the test facility, the test results of witness cables, and the short sample limit.

Coils for LARP Long Magnets

The new heavy ion synchrotron facility proposed by GSI will have two superconducting magnet rings in the same tunnel, with rigidities of 300 T /spl middot/ m and 100 T /spl middot/ m. Fast ramp times are needed. These can cause problems of ac loss and field distortion in the magnets. For the high-energy ring, a 1-m model dipole magnet has been built, based on the RHIC dipole design. This magnet was tested under boiling liquid helium in a vertical dewar. The quench current showed very little dependence on ramp rate. The ac losses, measured by an electrical method, were fitted to straight-line plots of loss/cycle versus ramp rate, thereby separating the eddy current and hysteresis components. These results were compared with calculated values, using parameters which had previously been measured on short samples of cable. Reasonably good agreement between theory and experiment was found, although the measured hysteresis loss is higher than expected in ramps to the highest field levels.

Final Development and Test Preparation of the First 3.7 m Long Nb3Sn Quadrupole by LARP

Following success of a prototype R&D, construction of a superconducting magnet system for J-PARC neutrino beam line has been carried out since 2005. A new conceptual beam line with the superconducting combined function magnets demonstrated the successful beam transport to the neutrino production target.

Measured and calculated losses in model dipole for GSI's heavy ion synchrotron

Brookhaven National Laboratory (BNL) has completed production of the superconducting multi-function magnets that are now installed as part of the HERA luminosity upgrade at DESY. The magnets, cryostats, and lead assemblies were designed and built at BNL. To fit inside the existing detectors, the coils plus cryostat structure had to meet a challenging radial budget (e.g., 39 mm horizontally). Two types of magnets were needed and three of each type were built. Each magnet contained normal and skew quadrupole, normal and skew dipole, and sextupole coils. The magnets operate in the /spl sim/1.5 T solenoid field of a detector. The quadrupole coils produce gradients up to 13 T/m. The dipole coils generate fields up to 0.3 T. Coils were wound under computer control using either seven-strand round cable or a single strand. To simultaneously avoid excessive synchrotron radiation background scattered from the beam pipe and yet have a small cryostat, one type of magnet used a tapered coil structure. The cryogenic system incorporates cooling with both 40 K helium and supercritical helium. All of the coils were tested in liquid helium in a vertical dewar. Quench test results have been excellent. The field quality of the magnets has met the stringent requirements imposed on interaction region magnets. One magnet of each type was tested at BNL as a completed assembly to verify the performance of the leads and cryostats. Two of each type were tested at DESY and then installed in the Zeus and H1 experiments. The remaining magnets are spares. Final results of quench testing, field quality measurements and cryogenic performance are reported.

Construction of Superconducting Magnet System for the J-PARC Neutrino Beam Line

The production run of superconducting magnets for the Relativistic Heavy Ion Collider (RHIC) project at Brookhaven National Laboratory (BNL) is well underway. Of the 288 arc dipoles needed for the collider, more than 120 have been delivered. More than 150 arc quadrupoles have been delivered. All of these magnets have been accepted for RHIC. This paper reports the construction and performance of these magnets. Novel features of design and test, introduced to enhance technical performance and control costs, are also discussed.