Joe Tien

Cells lying on a bed of microneedles: An approach to isolate mechanical force

We describe an approach to manipulate and measure mechanical interactions between cells and their underlying substrates by using microfabricated arrays of elastomeric, microneedle-like posts. By controlling the geometry of the posts, we varied the compliance of the substrate while holding other surface properties constant. Cells attached to, spread across, and deflected multiple posts. The deflections of the posts occurred independently of neighboring posts and, therefore, directly reported the subcellular distribution of traction forces. We report two classes of force-supporting adhesions that exhibit distinct force–size relationships. Force increased with size of adhesions for adhesions larger than 1 μm2, whereas no such correlation existed for smaller adhesions. By controlling cell adhesion on these micromechanical sensors, we showed that cell morphology regulates the magnitude of traction force generated by cells. Cells that were prevented from spreading and flattening against the substrate did not contract in response to stimulation by serum or lysophosphatidic acid, whereas spread cells did. Contractility in the unspread cells was rescued by expression of constitutively active RhoA. Together, these findings demonstrate a coordination of biochemical and mechanical signals to regulate cell adhesion and mechanics, and they introduce the use of arrays of mechanically isolated sensors to manipulate and measure the mechanical interactions of cells.

GEOMETRIC CONTROL OF SWITCHING BETWEEN GROWTH, APOPTOSIS, AND DIFFERENTIATION DURING ANGIOGENESIS USING MICROPATTERNED SUBSTRATES

SummaryPast studies using micropatterned substrates coated with adhesive islands of extracellular matrix revealed that capillary endothelial cells can be geometrically switched between growth and apoptosis. Endothelial cells cultured on single islands larger than 1500 µm2 spread and progressed through the cell cycle, whereas cells restricted to areas less than 500 µm2 failed to extend and underwent apoptosis. The present study addressed whether island geometries that constrained cell spreading to intermediate degrees, neither supporting cell growth nor inducing apoptosis, cause cells to differentiate. Endothelial cells cultured on substrates micropatterned with 10-µm-wide lines of fibronectin formed extensive cell-cell contacts and spread to approximately 1000 µm2. Within 72 h, cells shut off both growth and apoptosis programs and underwent differentiation, resulting in the formation of capillary tube-like structures containing a central lumen. Accumulation of extracellular matrix tendrils containing fibronectin and laminin beneath cells and reorganization of platelet endothelial cell adhesion molecule-positive cell-cell junctions along the lengths of the tubes preceded the formation of these structures. Cells cultured on wider (30-µm) lines also formed cell-cell contacts and aligned their actin cytoskeleton, but these cells spread to larger areas (2200 µm2), proliferated, and did not form tubes. Use of micropatterned substrates revealed that altering the geometry of cell spreading can switch endothelial cells among the three major genetic programs that govern angiogenesis—growth, apoptosis and differentiation. The system presented here provides a well-defined adhesive environment in which to further investigate the steps involved in angiogenesis.

Fabrication of microfluidic hydrogels using molded gelatin as a sacrificial element

This paper describes a general procedure for the formation of hydrogels that contain microfluidic networks. In this procedure, micromolded meshes of gelatin served as sacrificial materials. Encapsulation of gelatin meshes in a hydrogel and subsequent melting and flushing of the gelatin left behind interconnected channels in the hydrogel. The channels were as narrow as approximately 6 microm, and faithfully replicated the features in the original gelatin mesh. Fifty micrometre wide microfluidic networks in collagen and fibrin readily enabled delivery of macromolecules and particles into the channels and transport of macromolecules from channels into the bulk of the gels. Microfluidic gels were also suitable as scaffolds for cell culture, and could be seeded by human microvascular endothelial cells to form rudimentary endothelial networks for potential use in tissue engineering.

Microfluidic models of vascular functions.

In vitro studies of vascular physiology have traditionally relied on cultures of endothelial cells, smooth muscle cells, and pericytes grown on centimeter-scale plates, filters, and flow chambers. The introduction of microfluidic tools has revolutionized the study of vascular physiology by allowing researchers to create physiologically relevant culture models, at the same time greatly reducing the consumption of expensive reagents. By taking advantage of the small dimensions and laminar flow inherent in microfluidic systems, recent studies have created in vitro models that reproduce many features of the in vivo vascular microenvironment with fine spatial and temporal resolution. In this review, we highlight the advantages of microfluidics in four areas: the investigation of hemodynamics on a capillary length scale, the modulation of fluid streams over vascular cells, angiogenesis induced by the exposure of vascular cells to well-defined gradients in growth factors or pressure, and the growth of microvascular networks in biomaterials. Such unique capabilities at the microscale are rapidly advancing the understanding of microcirculatory dynamics, shear responses, and angiogenesis in health and disease as well as the ability to create in vivo-like blood vessels in vitro.

Fabrication of aligned microstructures with a single elastomeric stamp

The fabrication of complex patterns of aligned microstructures has required the use of multiple applications of lithography. Here we describe an approach for microfabrication that encodes the two-dimensional spatial information of several photomasks onto a single elastomeric stamp by mapping each photomask onto distinct heights on the surface of the stamp. Pressing the stamp against a surface collapses the topography of the stamp such that each recessed layer contacts the surface in stepwise sequence; the greater the applied pressure, the larger the area of the stamp that contacts the surface. After contact of each new layer with the surface, we use techniques of soft lithography (microcontact printing, microfluidics, and patterning through membranes) to pattern the surfaces that contact the stamp and those that do not with inorganic, organic, or living materials. Microfabrication through the use of multilevel stamps provides a promising alternative to conventional lithography for the construction of multicomponent, aligned surfaces; these structures may find use as components of microfluidic devices or biological patterns.

Effect of mechanical factors on the function of engineered human blood microvessels in microfluidic collagen gels

This work examines how mechanical signals affect the barrier function and stability of engineered human microvessels in microfluidic type I collagen gels. Constructs that were exposed to chronic low flow displayed high permeabilities to bovine serum albumin and 10 kDa dextran, numerous focal leaks, low size selectivity, and short lifespan of less than one week. Higher flows promoted barrier function and increased longevity; at the highest flows, the barrier function rivaled that observed in vivo, and all vessels survived to day 14. By studying the physiology of microvessels of different geometries, we established that shear stress and transmural pressure were the dominant mechanical signals that regulated barrier function and vascular stability, respectively. In microvessels that were exposed to high flow, elevation of intracellular cyclic AMP further increased the selectivity of the barrier and strongly suppressed cell proliferation. Computational models that incorporated stress dependence successfully predicted vascular phenotype. Our results indicate that the mechanical microenvironment plays a major role in the functionality and stability of engineered human microvessels in microfluidic collagen gels.

The role of cyclic AMP in normalizing the function of engineered human blood microvessels in microfluidic collagen gels

Nearly all engineered tissues must eventually be vascularized to survive. To this end, we and others have recently developed methods to synthesize extracellular matrix-based scaffolds that contain open microfluidic networks. These scaffolds serve as templates for the formation of endothelial tubes that can be perfused; whether such microvascular structures are stable and/or functional is largely unknown. Here, we show that compounds that elevate intracellular concentrations of the second messenger cyclic AMP (cAMP) strongly normalize the phenotype of engineered human microvessels in microfluidic type I collagen gels. Cyclic AMP-elevating agents promoted vascular stability and barrier function, and reduced cellular turnover. Under conditions that induced the highest levels of cAMP, the physiology of engineered microvessels in vitro quantitatively mirrored that of native vessels in vivo. Computational analysis indicated that cAMP stabilized vessels partly via its enhancement of barrier function.

Artificial lymphatic drainage systems for vascularized microfluidic scaffolds.

The formation of a stably perfused microvasculature continues to be a major challenge in tissue engineering. Previous work has suggested the importance of a sufficiently large transmural pressure in maintaining vascular stability and perfusion. Here we show that a system of empty channels that provides a drainage function analogous to that of lymphatic microvasculature in vivo can stabilize vascular adhesion and maintain perfusion rate in dense, hydraulically resistive fibrin scaffolds in vitro. In the absence of drainage, endothelial delamination increased as scaffold density increased from 6 to 30 mg/mL and scaffold hydraulic conductivity decreased by a factor of 20. Single drainage channels exerted only localized vascular stabilization, the extent of which depended on the distance between vessel and drainage as well as scaffold density. Computational modeling of these experiments yielded an estimate of 0.40-1.36 cm H2O for the minimum transmural pressure required for vascular stability. We further designed and constructed fibrin patches (0.8 × 0.9 cm(2)) that were perfused by a parallel array of vessels and drained by an orthogonal array of drainage channels; only with the drainage did the vessels display long-term stability and perfusion. This work underscores the importance of drainage in vascularization, especially when a dense, hydraulically resistive scaffold is used.

Bonding of macromolecular hydrogels using perturbants.

This work describes a method to bond patterned macromolecular gels into monolithic structures using perturbants. Bonding strengths for a variety of solutes follow a Hofmeister ordering; this result and optical measurements indicate that bonding occurs by reversible perturbation of contacting gels. The resulting microfluidic gels are mechanically robust and can serve as scaffolds for cell culture.

Plasma expanders stabilize human microvessels in microfluidic scaffolds

Plasma expanders such as dextran and hydroxyethyl starch (HES) are important components of solutions designed to maintain vascular volume in the clinical setting and to preserve organs ex vivo before transplantation. Here, we show that these polymers also exert stabilizing effects on engineered microvessels in microfluidic type I collagen and fibrin scaffolds. Standard growth media, which did not contain dextran or HES, led to severe leakage, vascular collapse, and catastrophic failure of perfusion. Remarkably, vessels that were provided with 3% dextran or 5% HES had few focal leaks, maintained adhesion to the scaffold, and were typically viable and patent for at least 2 weeks. We found that the junctional marker VE-cadherin localized to a wide band in the presence of plasma expanders, but only at concentrations that also stabilized vessels. In conjunction with a previous computational model (Wong et al., Biomaterials 2010;31:4706-4714), our results suggest that plasma expanders stabilize microvessels via physical mechanisms that enhance VE-cadherin localization at junctions and thereby limit vascular leakiness.