Jon Luecke

Diesel particle filter and fuel effects on heavy-duty diesel engine emissions.

The impacts of biodiesel and a continuously regenerated (catalyzed) diesel particle filter (DPF) on the emissions of volatile unburned hydrocarbons, carbonyls, and particle associated polycyclic aromatic hydrocarbons (PAH) and nitro-PAH, were investigated. Experiments were conducted on a 5.9 L Cummins ISB, heavy-duty diesel engine using certification ultra-low-sulfur diesel (ULSD, S ≤ 15 ppm), soy biodiesel (B100), and a 20% blend thereof (B20). Against the ULSD baseline, B20 and B100 reduced engine-out emissions of measured unburned volatile hydrocarbons and PM associated PAH and nitro-PAH by significant percentages (40% or more for B20 and higher percentage for B100). However, emissions of benzene were unaffected by the presence of biodiesel and emissions of naphthalene actually increased for B100. This suggests that the unsaturated FAME in soy-biodiesel can react to form aromatic rings in the diesel combustion environment. Methyl acrylate and methyl 3-butanoate were observed as significant species in the exhaust for B20 and B100 and may serve as markers of the presence of biodiesel in the fuel. The DPF was highly effective at converting gaseous hydrocarbons and PM associated PAH and total nitro-PAH. However, conversion of 1-nitropyrene by the DPF was less than 50% for all fuels. Blending of biodiesel caused a slight reduction in engine-out emissions of acrolein, but otherwise had little effect on carbonyl emissions. The DPF was highly effective for conversion of carbonyls, with the exception of formaldehyde. Formaldehyde emissions were increased by the DPF for ULSD and B20.

Impacts of Biodiesel Fuel Blends Oil Dilution on Light-Duty Diesel Engine Operation

Assesses oil dilution impacts on a diesel engine operating with a diesel particle filter, NOx storage, a selective catalytic reduction emission control system, and a soy-based 20% biodiesel fuel blend.

Impact of adaptation on flex-fuel vehicle emissions when fueled with E40.

Nine flex-fuel vehicles meeting Tier 1, light duty vehicle-low emission vehicle (LDV-LEV), light duty truck 2-LEV (LDT2-LEV), and Tier 2 emission standards were tested over hot-start and cold-start three-phase LA92 cycles for nonmethane organic gases, ethanol, acetaldehyde, formaldehyde, acetone, nitrous oxide, nitrogen oxides (NO(x)), carbon monoxide (CO), and carbon dioxide (CO(2)), as well as fuel economy. Emissions were measured immediately after refueling with E40. The vehicles had previously been adapted to either E10 or E76. An overall comparison of emissions and fuel economy behavior of vehicles running on E40 showed results generally consistent with adaptation to the blend after the length of the three-phase hot-start LA92 test procedure (1735 s, 11 miles). However, the single LDT2-LEV vehicle, a Dodge Caravan, continued to exhibit statistically significant differences in emissions for most pollutants when tested on E40 depending on whether the vehicle had been previously adapted to E10 or E76. The results were consistent with an overestimate of the amount of ethanol in the fuel when E40 was added immediately after the use of E76. Increasing ethanol concentration in fuel led to reductions in fuel economy, NO(x), CO, CO(2), and acetone emissions as well as increases in emissions of ethanol, acetaldehyde, and formaldehyde.

Impact of Higher Alcohols Blended in Gasoline on Light-Duty Vehicle Exhaust Emissions

Certification gasoline was splash blended with alcohols to produce four blends: ethanol (16 vol%), n-butanol (17 vol%), i-butanol (21 vol%), and an i-butanol (12 vol%)/ethanol (7 vol%) mixture; these fuels were tested in a 2009 Honda Odyssey (a Tier 2 Bin 5 vehicle) over triplicate LA92 cycles. Emissions of oxides of nitrogen, carbon monoxide, non-methane organic gases (NMOG), unburned alcohols, carbonyls, and C1-C8 hydrocarbons (particularly 1,3-butadiene and benzene) were determined. Large, statistically significant fuel effects on regulated emissions were a 29% reduction in CO from E16 and a 60% increase in formaldehyde emissions from i-butanol, compared to certification gasoline. Ethanol produced the highest unburned alcohol emissions of 1.38 mg/mile ethanol, while butanols produced much lower unburned alcohol emissions (0.17 mg/mile n-butanol, and 0.30 mg/mile i-butanol); these reductions were offset by higher emissions of carbonyls. Formaldehyde, acetaldehyde, and butyraldehyde were the most significant carbonyls from the n-butanol blend, while formaldehyde, acetone, and 2-methylpropanal were the most significant from the i-butanol blend. The 12% i-butanol/7% ethanol blend was designed to produce no increase in gasoline vapor pressure. This fuels exhaust emissions contained the lowest total oxygenates among the alcohol blends and the lowest NMOG of all fuels tested.

Fuels for Advanced Combustion Engines Research Diesel Fuels: Analysis of Physical and Chemical Properties

The CRC Fuels for Advanced Combustion Engines working group has worked to identify a matrix of research diesel fuels for use in advanced combustion research applications. Nine fuels were specified and formulated to investigate the effects of cetane number aromatic content and 90% distillation fraction. Standard ASTM analyses were performed on the fuels as well as GC/MS and /u1H//u1/u3C NMR analyses and thermodynamic characterizations. Details of the actual results of the fuel formulations compared with the design values are presented, as well as results from standard analyses, such as heating value, viscosity and density. Cetane number characterizations were accomplished by using both the engine method and the Ignition Quality Tester (IQT/sT) apparatus.

The Impacts of Mid-Level Alcohol Content in Gasoline on SIDI Engine-Out and Tailpipe Emissions

The influences of ethanol and iso-butanol on gasoline engine performance, engine-out and tailpipe emissions were studied using a General Motors (GM) 2.0L turbocharged gasoline spark ignition direct injection (SIDI) engine. U.S. federal certification gasoline (E0), two ethanol-blended fuels (E10 and E20), and 11.7% iso-butanol blended fuels were tested. Fourier-Transform Infrared (FTIR) spectroscopy was used to measure non-regulated species including methane, ethylene, acetylene, formaldehyde, acetaldehyde, isobutylene, 1,3-butadiene, n-pentane, and iso-octane. A Fast Mobility Particle Sizer (FMPS) spectrometer was used to measure the particle number (PN) size distribution in the range from 5.6 to 560 nm. The regulated emissions total hydrocarbon (THC), carbon monoxide (CO), and oxides of nitrogen (NOx ) were also measured. Both engine-out and tailpipe emissions results are presented as functions of alcohol content. In general, the alcohols tested reduced total PN emissions, with iso-butanol demonstrating the greatest reduction. Increasing ethanol content and iso-butanol increased formaldehyde emissions, with iso-butanol exhibiting the highest increase. Iso-butanol increased iso-butylene emission; however, it reduced emissions of 1,3-butadiene. Within the context of this study, the alcohols did not significantly change the other regulated emissions.© 2010 ASME