Jorge Regueiro

Ultrasound-assisted emulsification–microextraction of emergent contaminants and pesticides in environmental waters

The analytical use of ultrasound-generated emulsions has recently found a growing interest to improve efficiency in liquid-liquid extraction since they increase the speed of the mass transfer between the two immiscible phases implied. Thus, dispersed droplets can act as efficient liquid-liquid microextractors in the continuous phase, and later they can be readily separated by centrifugation. A novel method based on ultrasound-assisted emulsification-microextraction (USAEME) and gas chromatography coupled to mass spectrometry (GC/MS) has been developed for the analysis of synthetic musk fragrances, phthalate esters and lindane in water samples. Extraction conditions were optimized using a multivariate approach. Compounds were extracted during 10 min in an acoustically emulsified media formed by 100 microL chloroform and 10 mL sample (enrichment factor=100). The method performance was studied in terms of accuracy (recovery=78-114%), linearity (R2> or =0.9990) and repeatability (RSD< or =14%). Limits of detection (LODs) were at the pg mL(-1) level for most of compounds, and at the sub-ng mL(-1) level for the most ubiquitous phthalate esters. USAEME is proposed as an efficient, fast, simple and non-expensive alternative to other extraction techniques such as SPE, SPME and LPME for the analysis of environmental waters including bottled, tap, river, municipal swimming pool, sewage and seaport water samples. Since no matrix effect has been found for any of the water types analyzed, quantification could be carried out by using conventional external calibration, thus allowing a higher throughput of the analysis in comparison with other microextraction techniques based on equilibrium such as solid-phase microextraction.

Trace analysis of parabens, triclosan and related chlorophenols in water by headspace solid-phase microextraction with in situ derivatization and gas chromatography-tandem mass spectrometry.

An in situ derivatization solid-phase microextraction method has been developed for the determination of parabens, triclosan and related chlorophenols in water. Acetylated derivatives are selectively determined using gas chromatography with tandem mass spectrometry. Parameters affecting both derivatization and SPME procedures, such as fiber coating, extraction mode, temperature, volume of derivatizating reagent and ionic strength, are studied and optimized through a multifactorial experimental design. The performance of the method is studied in terms of accuracy, linearity, precision and limits of detection. Quantitative recoveries (> or =82%) and satisfactory precision (RSD< or =12%) are obtained. Limits of detection at the low picogram per millilitre level are achieved for all target compounds. Linearity is studied in a wide range of concentrations and an analysis of variance with a lack-of-fit test is run to validate the calibration data. Extraction time profiles are also obtained. Finally, the applicability of the proposed method is demonstrated for several real samples including river water, wastewaters and swimming pool water. Since no matrix effects are observed, quantification can readily be carried out by external calibration with ultrapure water standards.

Ultrasound-assisted emulsification-microextraction of phenolic preservatives in water.

Simultaneous ultrasound-assisted emulsification-microextraction (USAEME) and derivatization combined with gas chromatography-tandem mass spectrometry (GC-MS/MS) is proposed for the first time for the analysis of parabens, triclosan and related phenols in water samples. In situ acetylation was successfully applied for the derivatization of target compounds with high efficiency using non-expensive reagents. The proposed method exhibits many advantages such as simplicity, efficiency, low cost, and minimum solvent consumption. In addition, the whole analytical process, including sample preparation and determination, is performed in only 20 min. A multifactorial experimental design was employed to study and optimize the main variables potentially affecting the microextraction and derivatization processes (extraction solvent, phase ratio, sodium chloride concentration, extraction time, and acetic anhydride volume). The performance of the method was studied in terms of accuracy, linearity, precision, and enrichment factor. Quantitative recoveries (>or=85%) were obtained for all target compounds, and method precision was also satisfactory (RSD<or=13%) even for complex samples. Enrichment factors ranging from 100 to 200 were obtained, allowing achieving limits of detection at the low picogram per millilitre for most of the target compounds. Several real samples, including wastewaters, river waters and swimming pool water, were analyzed. Since matrix effects were not observed, quantification can easily be performed using external calibration with acetylated standards, allowing a high sample throughput.

Analysis of industrial contaminants in indoor air: Part 1. Volatile organic compounds, carbonyl compounds, polycyclic aromatic hydrocarbons and polychlorinated biphenyls.

This article reviews recent literature on the analysis of industrial contaminants in indoor air in the framework of the REACH project, which is mainly intended to improve protection of human health and the environment from the risks of more than 34 millions of chemical substances. Industrial pollutants that can be found in indoor air may be of very different types and origin, belonging to the volatile organic compounds (VOCs) and semivolatile organic compounds (SVOCs) categories. Several compounds have been classified into the priority organic pollutants (POPs) class such as polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins and furans (PCDD/PCDFs) and related polychlorinated compounds, and polycyclic aromatic hydrocarbons (PAHs). Many of these compounds are partially associated to the air gas phase, but also to the suspended particulate matter. Furthermore, settled dust can act as a concentrator for the less volatile pollutants and has become a matrix of great concern for indoors contamination. Main literature considered in this review are papers from the last 10 years reporting analytical developments and applications regarding VOCs, aldehydes and other carbonyls, PCBs, PCDDs, PCDFs, and PAHs in the indoor environment. Sample collection and pretreatment, analyte extraction, clean-up procedures, determination techniques, performance results, as well as compound concentrations in indoor samples, are summarized and discussed. Emergent contaminants and pesticides related to the industrial development that can be found in indoor air are reviewed in a second part in this volume.

Analysis of industrial contaminants in indoor air. Part 2. Emergent contaminants and pesticides

This article reviews recent literature on the analysis of several contaminants related to the industrial development in indoor air in the framework of the REACH project. In this second part, the attention is focused on emergent contaminants and biocides. Among these chemicals, phthalates, polybrominated and phosphate flame retardants, fragrances, pesticides, as well as other emerging pollutants, are increasing their environmental and health concern and are extensively found in indoor air. Some of them are suspected to behave as priority organic pollutants (POPs) and/or endocrine disrupting compounds (EDC), and can be found both in air and associated to the suspended particulate matter (PM) and settled dust. Main literature considered for this review is from the last ten years, reporting analytical developments and applications regarding the considered contaminants in the indoor environment. Sample collection and pretreatment, analyte extraction or desorption, clean-up procedures, determination techniques, and performance results are summarized and discussed.

Development of a method based on sorbent trapping followed by solid-phase microextraction for the determination of synthetic musks in indoor air

Synthetic musks are extensively used as fragrance components in a wide range of consumer and personal care products such as detergents, shampoos, perfumes and other cosmetic products. Amongst them, galaxolide and tonalide have become ubiquitous pollutants due to their continuous releasing into the environment. Because of their nature as artificial fragrances, inhalation should be considered as an important exposure pathway, especially in indoor environments. However, up to now very few studies have been carried out to determine these emergent pollutants indoors. In this work, a simple and highly sensitive methodology for the analysis of synthetic musk fragrances in indoor air samples is presented. The proposed methodology combines solid-phase extraction (SPE) and solid-phase microextraction (SPME), followed by gas chromatography-mass spectrometry (GC/MS). To the best of our knowledge, this is the first method based on SPME for the analysis of musks in air. By active sampling, musks present in air were adsorbed onto 25mg Tenax and then transferred to a SPME fiber in the headspace mode (HS). An experimental design strategy was used to optimize main factors potentially affecting the microextraction process such as fiber coating, temperature and the addition of a microvolume of organic solvent to the solid sorbent prior to SPME. Breakthrough of the SPE sorbent was studied from 1 to 10m(3) without significant losses. Recovery studies were performed at two concentration levels (2 and 20ngm(-3)), obtaining quantitative recoveries (>/=85%) by external calibration. A comprehensive study was performed in order to estimate the limits of detection taking into account the contamination risks and laboratory blanks. Values at the sub ngm(-3) level were achieved for all the target compounds sampling 5m(3) air. External calibration, not requiring the complete sampling process, demonstrated to be suitable for the quantification of all musk compounds. Finally, several indoor environments were analyzed using the proposed method.

Determination of bisphenols in beverages by mixed-mode solid-phase extraction and liquid chromatography coupled to tandem mass spectrometry

Facing growing restrictions on the use of bisphenol A in food contact materials, several bisphenol analogs are arising as major alternatives to replace this chemical in most of its applications. This work reports a simple and robust method based on mixed-mode solid-phase extraction and stable-isotope dilution liquid chromatography-tandem mass spectrometry for the analysis of bisphenol A and its main analogs - bisphenol S, 4,4-sulfonylbis(2-methylphenol), bisphenol F, bisphenol E, bisphenol B, bisphenol Z, bisphenol AF, bisphenol AP, tetrabromobisphenol A and bisphenol P - in alcoholic and non-alcoholic beverages. Mixed-mode solid-phase extraction, combining cationic exchange and reversed-phase mechanisms, was optimized to provide a selective extraction and purification of the target analytes. Derivatization of bisphenols with pyridine-3-sulfonyl chloride allowed increasing their ionization efficiency by electrospray ionization. Validation of the proposed method was performed in terms of selectivity, matrix effects, linearity, precision, measurement uncertainty, trueness and limits of detection. Satisfactory repeatability and intermediate precision were obtained; the related relative standard deviations were ≤9% and ≤12%, respectively. The relative expanded uncertainty (k=2) was below 20% for all bisphenol analogs and the trueness of the method was demonstrated by recovery experiments. Limits of detection (LOD) ranged from 1.6ngL(-1) to 27.9ngL(-1) for all compounds. Finally, several canned and non-canned beverages were analyzed to demonstrate the applicability of the method. Only bisphenol A and three bisphenol F isomers were detected in any of the samples. Bisphenol A concentration ranged from <LOD to 1.26±0.09μgL(-1), whereas 4,4-bisphenol F varied from <LOD to 1.00±0.08μgL(-1). To the best of our knowledge, 2,2-bisphenol F and 2,4-bisphenol F were reported for the first time in beverages, at concentration levels up to 0.12 and 0.51μgL(-1), respectively.

Development and validation of a stable-isotope dilution liquid chromatography–tandem mass spectrometry method for the determination of bisphenols in ready-made meals ☆

Due to their growing consumption, ready-made meals are a major dietary component for many people in todays society, representing an important potential route of human exposure to several food contaminants. The recent restrictions in the use of bisphenol A have led the plastic industry to look for alternative chemicals, most of them belonging to the same family of p,p-bisphenols. The aim of the current work was to develop and validate a method based on stable-isotope dilution liquid chromatography-tandem mass spectrometry for the analysis of bisphenol A and its main analogs - bisphenol S, 4,4-sulfonylbis(2-methylphenol), bisphenol F, bisphenol E, bisphenol B, bisphenol Z, bisphenol AF, bisphenol AP, tetrabromobisphenol A and bisphenol P - in solid foodstuffs, and particularly in ready-made meals. Extraction was carried out by ultrasound-assisted extraction after sample disruption with sand. A selective solid-phase extraction procedure was then applied to reduce potential matrix interferences. Derivatization of bisphenols with pyridine-3-sulfonyl chloride increased their ionization efficiency by electrospray ionization. Validation of the proposed method was performed in terms of selectivity, matrix effects, linearity, precision, measurement uncertainty, trueness and limits of detection. Satisfactory repeatability and intermediate precision were obtained; the related relative standard deviations were ≤7.8% and ≤10%, respectively. The relative expanded uncertainty (k=2) was below 17% for all bisphenol analogs and the trueness of the method was demonstrated by spike recovery experiments. Low limits of detection, in the range from 0.025μgkg(-1) to 0.140μgkg(-1), were obtained for all compounds. To demonstrate the applicability of the proposed method, it was eventually applied to several ready-made meals purchased from different supermarkets in Belgium.

Development of a solid-phase microextraction-gas chromatography-tandem mass spectrometry method for the analysis of chlorinated toluenes in environmental waters.

In the present work, a simple and fast methodology has been developed for the analysis of chlorotoluenes in water samples using solid-phase microextraction (SPME) coupled to gas chromatography-tandem mass spectrometry (GC/MS/MS). A multifactorial experimental design strategy was used for studying the influence on extraction yield of factors such as fiber coating, extraction mode, temperature, and addition of sodium chloride. Quantitative recoveries (>/=84%) and satisfactory precision (relative standard deviations (RSD)</=12%) have been obtained. Limits of detection (LODs) in the sub-picogram per litre level from 0.030 to 0.330 were achieved for all analyzed compounds. Linearity was studied in a wide range of concentrations and an analysis of variance with a lack-of-fit test was run to validate the calibration data. Extraction time profiles were also studied, showing that most of chlorotoluenes reached the equilibrium or were close to it. Finally, the applicability of the proposed method has been demonstrated for real samples including river and sewage water samples. Since no matrix effects were observed, quantification could readily be carried out by external calibration with ultrapure water standards.

Determination of dimethyl fumarate and other potential allergens in desiccant and antimould sachets

A method for the determination of dimethyl fumarate (DMF), benzothiazole (BT) and tert-butylphenol (TBP) in desiccant and antimould agents employed for protecting consumer products from humidity and mould has been developed. The method is based on ultrasound-assisted extraction (UAE) followed by GC-MS analysis. Parameters that could affect the extraction of the compounds have been optimised using a multivariate approach. In the final conditions, the extraction is performed using only 0.5 or 1xa0mL ethyl acetate and applying ultrasound energy for 5xa0min. Simultaneous extractions could also be carried out in 5xa0min without losing efficiency. The method was validated showing good linearity (R2 >0.995). Both intra- and inter-day precisions were studied at several concentration levels, being satisfactory in all cases (RSD <10%). Recovery was evaluated in four real desiccant samples at different compound concentrations, ranging between 87% and 109%. Limits of detection and quantification were in the low nanogramme per gramme level, thus allowing the determination of DMF at concentrations well below the limit established by the recent EU Directive (0.1xa0μg/g). The proposed procedure was applied to the determination of the target compounds in several desiccant and antimould samples. Although most of them were simply labelled as “silica gel”, more than 70% of the tested samples contained high amounts of DMF, many of them at the high microgram per gramme level. Many samples also showed the presence of the other two potential allergens. These results demonstrate that the content of the “desiccant” sachets and tablets in consumer products does not usually belong with the label of the desiccant, and hence, the high risk of exposition to the powerful allergen DMF and other potentially harmful chemicals through consumer goods should be a matter of concern.